The chemostat reactor: A stability analysis and model predictive control

In this paper, a learning-based predictive control (LPC) scheme is proposed for adaptive optimal control of discrete-time nonlinear systems under stochastic disturbances. The proposed LPC scheme is different from conventional model predictive control (MPC), which uses open-loop optimization or simplified closed-loop optimal control techniques in each horizon. In LPC, the control task in each horizon is formulated as a closed-loop nonlinear optimal control problem and a finite-horizon iterative reinforcement learning (RL) algorithm is developed to obtain the closed-loop optimal/suboptimal solutions. Therefore, in LPC, RL and adaptive dynamic programming (ADP) are used as a new class of closed-loop learning-based optimization techniques for nonlinear predictive control with stochastic disturbances. Moreover, LPC also decomposes the infinite-horizon optimal control problem in previous RL and ADP methods into a series of finite horizon problems, so that the computational costs are reduced and the learning efficiency can be improved. Convergence of the finite-horizon iterative RL algorithm in each prediction horizon and the Lyapunov stability of the closed-loop control system are proved. Moreover, by using successive policy updates between adjoint time horizons, LPC also has lower computational costs than conventional MPC which has independent optimization procedures between two different prediction horizons. Simulation results illustrate that compared with conventional nonlinear MPC as well as ADP, the proposed LPC scheme can obtain a better performance both in terms of policy optimality and computational efficiency.

Model predictive control (MPC) is used in the CO2 removal process in the Subang field to improve its control performance. MPC is used to maintain the CO2 concentration at the sweet gas output by controlling the feed gas pressure (PIC-1101), makeup water flow rate (FIC-1102), and amine flow rate (FIC-1103). The empirical model applied to MPC to represent the process model is the auto-regressive exogenous (ARX) model. The ARX model is compared with the first order plus dead time (FOPDT) model based on the root mean square error (RMSE) between the model and the actual process, then MPC parameters are tuned which include sampling time (T), prediction horizon (P) and control horizon (M) to control for the three variables. Improved control performance is measured based on the integral square error (ISE). The results show that the ARX model is the best model for the CO2 removal process with an RMSE value of 35%-91% smaller than the FOPDT model. The optimal control parameters Prediction Horizon (P), Control Horizon (M) and Sampling Time (T) in the CO2 removal process are 75, 25 and 1 on PIC-1101, 25, 10 and 1 on FIC-1102, and 30, 25 and 1 on FIC-1103. The MPC-ARX (MPC using ARX model) can improve the control performance of 33% in the servo control and 6-56% on the regulatory control. However, not all of them showed an increase in control performance improvement from previous studies even though they had used the best model (ARX). This is due to the MPC parameter setting that is not yet appropriate, so it needs to be retuning.

Linear switched reluctance motor (LSRM) has the advantages of simple structure, strong robustness, high efficiency, low cost, and low maintenance. They are used in many fields. This paper mainly studies the position tracking control of linear switched reluctance motor and its model predictive controller design. First, the physical system of the linear switched reluctance motor is analyzed and a discrete equation of its state space model is constructed. In order to better eliminate the static error of the motor during position tracking, the increment form of the state equation of the linear switched reluctance motor is further given. By constructing the prediction equation of the motor and predicting the system output in a given time domain. The problem of solving the optimal control sequence online at each sampling time is further transformed into a standard quadratic programming problem. So the optimal control sequence with state constraints and control quantity constraints can be further obtained. To further optimize the design of the model predictive controller, the effects are compared among different prediction horizon, control horizon, weighting factors, and sampling time on the control performance of the model predictive controller to achieve the optimal control effect. Finally, simulation results prove that the model predictive controller has a good control effect on the position tracking of the linear switched reluctance motor.

This paper proposes a solution method for the discrete-time long-term dynamic portfolio optimization problem with state and asset allocation constraints. We use the ideas of Model Predictive Control (MPC) to solve the constrained stochastic control problem. MPC is a solution technique which was developed to solve constrained optimal control problems for deterministic control applications. MPC solves the optimal control problem with a receding horizon where a series of consecutive open-loop optimal control problems is solved. The aim of this paper is to develop an MPC approach to the problem of long-term portfolio optimization when the expected returns of the risky assets are modeled using a factor model based on stochastic Gaussian processes. We prove that MPC is a suboptimal control strategy for stochastic systems which uses the new information advantageously and thus is better than the pure optimal open-loop control. For the open-loop optimal control optimization, we derive the conditional portfolio distribution and the corresponding conditional portfolio mean and variance. The mean and the variance depend on future decision about the asset allocation. For the dynamic portfolio optimization problem, we consider constraints on the asset allocation as well as probabilistic constraints on the attainable values of the portfolio wealth. We discuss two different objectives, a classical mean–variance objective and the objective to maximize the probability of exceeding a predetermined value of the portfolio. The dynamic portfolio optimization problem is stated, and the solution via MPC is explained in detail. The results are then illustrated in a case study.

Multi-vector model predictive control of permanent magnet synchronous motor can effectively overcome the shortcomings of conventional single-vector model predictive control such as large motor current ripples and limited control accuracy, but its control performance is more susceptible to the influence of motor parameter perturbation. To improve the robustness of the multi-vector predictive control algorithm under the motor parameter perturbation, a novel nonparametric three-vector model predictive current control method for permanent magnet synchronous motors is proposed in this paper. Through constructing an ultra-local predictive current model based on the input and output signals of the permanent magnet synchronous motor, the influence of motor parameter perturbation on current prediction is avoided, and a disturbance observer is designed to estimate the non-modeled and perturbed parts of the ultra-local model. In addition, the direct calculation method of vector duty cycles based on current error is introduced to suppress the influence of motor parameter uncertainty on the duty cycle calculation link, which further improves the system robustness. Finally, simulations and experiments of the proposed method are demonstrated to compare with the conventional parametric three-vector model predictive current control, and the results show that the proposed control strategy can effectively suppress the disturbances caused by the motor parameters and ensure the steady-state performance during motor operation.

In this paper, we consider nonlinear partial integro-differential equations (PIDEs) with gradient-independent Lipschitz continuous nonlinearities and prove that deep neural networks with ReLU activation function can approximate solutions of such semilinear PIDEs without curse of dimensionality in the sense that the required number of parameters in the deep neural networks increases at most polynomially in both the dimension [Formula: see text] of the corresponding PIDE and the reciprocal of the prescribed accuracy [Formula: see text].

Model predictive control (MPC) as a nonlinear control method, is being studied for a wide variety of power electronics applications targeting various power ranges. The fast dynamic response, robustness under different load conditions, multi-objective control, and simplicity of implementation are the main features of MPC. However, the implementation of finite control set MPC (FCS-MPC) or direct MPC in its basic form for multilevel converters (MLCs) demonstrates the inability to generate the staircase multilevel output voltage waveform in a voltage sourced inverter (VSI) application. Adding a reference evaluation block to the basic FCS-MPC method can significantly improve its multilevel voltage generation capability. In this paper, an enhanced model predictive nearest level control (EMP-NLC) is proposed and implemented on a 5-Level flying capacitor multilevel converter (FCMC). The proposed method is simulated under different load conditions, while a comparison against existing MPC techniques is also presented. Experimental results verified the efficacy of the proposed controller.

Model predictive control (MPC) presents important advantages in the control of the power converter and drives such as, fast dynamic response and capability to include nonlinear constrains. These have positioned MPC as a powerful and realistic control strategy, however, it also has disadvantages such as variable switching frequency and parameter sensitivity. This paper applied a modulated model predictive speed control that guarantees a fix switching frequency and, thanks to disturbance compensation, robustness to parameters variation. The strategy is validated and compared to finite set model predictive speed control through simulation results.

Fil: Giovanini, Leonardo Luis. Consejo Nacional de Investigaciones Cientificas y Tecnicas. Centro Cientifico Tecnologico Conicet - Santa Fe. Instituto de Investigacion en Senales, Sistemas e Inteligencia Computacional. Universidad Nacional del Litoral. Facultad de Ingenieria y Ciencias Hidricas. Instituto de Investigacion en Senales, Sistemas e Inteligencia Computacional; Argentina

The need for cost-effective fuel economy improvements has driven the introduction of automatic transmissions with an increasing number of gear ratios. Incorporation of interlocking dog clutches in these transmissions decreases package space and increases efficiency, as compared to conventional dry or wet clutches. Unlike friction based clutches, interlocking dog clutches require very precise rotational speed matching prior to engagement. Precise engine speed control is therefore critical to maintaining high shift quality. This research focuses on controlling the engine speed during a gearshift period by manipulating throttle position and combustion phasing. Model predictive control (MPC) is advantageous in this application since the speed profile of a future prediction horizon is known with relatively high confidence. The MPC can find the optimal control actions to achieve the designated speed target without invoking unnecessary actuator manipulation and violating hardware and combustion constraints. This research utilizes linear parameter varying (LPV) MPC to control the engine speed during the gearshift period. Combustion stability constraints are considered with a control oriented covariance of indicated mean effective pressure model (COV of IMEP). The proposed MPC engine speed controller is validated with a high-fidelity 0-dimensional engine model with crank angle resolution. Four case studies, based on simulation, investigate the impact of different MPC design parameters. They also demonstrate that the proposed MPC engine controller successfully achieves the speed reference tracking objective while considering combustion variation constraints.

Fifty-seven per cent of all water supply systems in the Netherlands are controlled by model predictive flow control; the other 43% are controlled by conventional level-based flow control. The differences between conventional level-based flow control and model predictive control were investigated in experiments at five full-scale water supply systems in the first half of 2011. Quality parameters of the drinking water and energy consumption of the treatment and distribution processes were measured and analysed. The experiments showed that the turbidity values are 12–28% lower, and particle volume values 12–42% lower for the systems which are controlled by model predictive flow control. The overall energy consumption of water supply systems controlled by predictive flow control is 1.0–5.3% lower than conventional level-based flow controlled systems, and the overall energy costs are 1.7–7.4% lower.

Under unbalanced dc links, the control of a three-phase Vienna rectifier is challenging. To deal with the unbalanced dc links, the optimal switching sequence model predictive control (MPC) regulates the neutral-point (NP) voltage through preselecting a redundant vector and grid current by reconstructing duty cycles of the optimal switching sequence. However, its one-redundant-vector-per-control-interval characteristic leads to large NP voltage ripple. To solve this problem, in this article, a model predictive duty cycle control method is proposed for three-phase Vienna rectifiers under unbalanced dc links. First, we study the impacts of duty cycles on the variations of instantaneous current, and then, the three-phase duty cycles are derived by predefined objective function minimization. Second, considering both the operational characteristics and unbalanced dc links of the Vienna rectifier, a new modification method for duty cycles is presented. This method ensures the grid current quality and decouples the control of grid current and NP voltage. Finally, an MPC-based NP voltage control strategy is proposed to reduce the NP voltage ripple. Experimental results demonstrate that the presented method can effectively reduce the NP voltage ripple.

Model predictive control (MPC) is an efficient and growing approach to power converter control. This paper proposes an improved and simplified model predictive current control (MPCC) technique for a four-level nested neutral point clamped (4L-NNPC) converter. Conventional MPCC exhibits better performances as compared to the conventional linear control system such as fast dynamic response, consideration of the system constraints, and nonlinearities. However, the application of the conventional model predictive current control (MPCC) approach on complex systems provokes a significant number of calculations, which is the main hurdle to its practical implementation. To fix this flaw, this paper proposes an effective algorithm to shorten the execution time of the conventional MPCC. In this proposed technique, 216 current predictions of the conventional MPCC are skipped and converted into one required voltage vector (RVV) prediction. With this equivalent reference voltage transformation, the calculation burden of MPCC is significantly reduced, while the output performance is not influenced. The results of the simplified MPCC for the 4L-NNPC converter are analyzed and compared with the conventional MPCC. The computational time is reduced by 19.56% using the simplified MPCC, while keeping an approximately similar error of output currents. The switching frequency and total harmonic distortion (THD) of the proposed method are reduced by 8.16% and 0.07%, respectively, as compared to the conventional technique. These results demonstrate the fact that that the performance of a conventional MPCC is enhanced with the proposed MPCC. The proposed algorithm can be applied to several inverter topologies.

Nowadays, a model predictive control has gained a lot of attractions for power converter. To overcome the defects of the conventional model predictive control and achieve better performance, this article presents a multivector model predictive power control (MV-MPPC) with low computational burden for the grid-tied quasi-Z-source inverter (qZSI). Compared with the conventional model predictive power control (MPPC) that adopts only one vector in one control period, the proposed MV-MPPC applies several vectors including two active vectors, one null vector, and one shoot-through (ST) vector to fulfill the expected performance for the grid-tied qZSI. By calculating the optimal duty ratios of the ST vector, the inductor current ripple can be greatly reduced. To eliminate the weighting factor, a modified sliding-mode control method for simultaneously controlling the capacitor voltage and the inductor current to their setting points is proposed. Furthermore, a quick and effective optimal sector selection method is given, which chooses the optimal sector through a look-up table instead of a bunch of complex calculations. Hence, the computational burden of the proposed MV-MPPC is decreased with significance. Both simulation and experimental results are shown to validate the effectiveness and the advantages of the proposed method.

The research object of this paper is single-phase PWM rectifier, the purpose is to reduce the total harmonic distortion (THD) of the grid-side current. A model predictive current control (MPCC) with fixed switching frequency and dead-time compensation is proposed. First, a combination of an effective vector and two zero vectors is used to fix the switching frequency, and a current prediction equation based on the effective vector’s optimal action time is derived. The optimal action time is resolved from the cost function. Furthermore, in order to perfect the established prediction model and suppress the current waveform distortion as a consequence of the dead-time effect, the dead-time’s influence on the switching vector’s action time is analyzed, and the current prediction equation is revised. According to the experimental results, the conclusion is that, firstly, compared with finite-control-set model predictive control, proportional-integral-based instantaneous current control (PI-ICC) scheme and model predictive direct power control (MP-DPC), the proposed MPCC has the lowest current THD. In addition, the proposed MPCC has a shorter execution time than MP-DPC and has fewer adjusted parameters than PI-ICC. In addition, the dead-time compensation scheme successfully suppresses the zero-current clamping effects, and reduce the current THD.