The modeling of a two-diode photovoltaic module for power system simulations

Long term supporting schemes for photovoltaic (PV) system installation have led to accommodating large numbers of PV systems within load pockets in distribution grids. High penetrations of PV systems can cause new technical challenges, such as voltage rise due to reverse power flow during light load and high PV generation conditions. Therefore, new strategies are required to address the associated challenges. Moreover, due to these changes in distribution grids, a different response behavior of the distribution grid on the transmission side can be expected. Hence, a new equivalent model of distribution grids with high penetration of PV systems is needed to be addressed for future power system studies. The thesis contributions lie in three parts. The first part of the thesis copes with the PV modelling. A non-proprietary PV model of a three-phase, single stage PV system is developed in PSCAD/EMTDC and PowerFactory. Three different reactive power regulation strategies are incorporated into the models and their behavior are investigated in both simulation platforms using a distribution system with PV systems. In the second part of the thesis, the voltage rise problem is remedied by use of reactive power. On the other hand, considering large numbers of PV systems in grids, unnecessary reactive power consumption by PV systems first increases total line losses, and second it may also jeopardize the stability of the network in the case of contingencies in conventional power plants, which supply reactive power. Thus, this thesis investigates and develops the novel schemes to reduce reactive power flows while still keeping voltage within designated limits via three different approaches: 1. decentralized voltage control to the pre-defined set-points 2. developing a coordinated active power dependent (APD) voltage regulation Q(P) using local signals 3. developing a multi-objective coordinated droop-based voltage (DBV) regulation Q(V) using local signals In the third part of the thesis, furthermore, a gray-box load modeling is used to develop a new static equivalent model of a complex distribution grid with large numbers of PV systems embedded with voltage support schemes. In the proposed model, variations of voltage at the connection point simulate variations of the model’s active and reactive power. This model can simply be integrated into load-flow programs and replace the complex distribution grid, while still keeping the overall accuracy high. The thesis results, in conclusion, demonstrate: i) using rms-based simulations in PowerFactory can provide us with quite similar results using the time domain instantaneous values in PSCAD platform; ii) decentralized voltage control to specific setpoints through the PV systems in the distribution grid is fundamentally impossible due to the high level voltage control interaction and directionality among the PV systems; iii) the proposed APD method can regulate the voltage under the steady-state voltage limit and consume less total reactive power in contrast to the standard characteristic Cosf (P) proposed by German Grid Codes; iv) the proposed optimized DBV method can directly address voltage and successfully regulate it to the upper steady-state voltage limit by causing minimum reactive power consumption as well as line losses; v) it is beneficial to address PV systems as a separate entity in the equivalencing of distribution grids with high density of PV systems.

Solar ship, which integrates the solar photovoltaic (PV) system into its own ship power system, is becoming one kinds of most promising and fastest developing green ship. Since the electric energy transformed by PV system is provided to the power load through the ship's distribution system, the output power of synchronous generator will be reduced in proportion. Especially, if the matching relationship among solar PV system, energy storage system and the power load requirement is precisely analyzed and the operation characteristics and reliability of solar inverter have already meet the strict test standards for marine equipment, the design capacity of synchronous generators could also be reduced. The off-grid mode and grid mode are the main way of integrated application of solar power photovoltaic system of ship. And the solar PV system is a kind of inverter power supply, which is essentially based on the electronic inverted technology, so PV system can be regarded as a ‘fragile power source’ with ‘zero inertia’. Therefore, the influence of solar photovoltaic grid-connected system to the power flow and power quality of the ship power system cannot be ignored. And the effect of photovoltaic system on the power quality of transient and steady-state and flow calculation remains to be studied. This paper mainly research the changes of power load flow calculation(PLFC) on the system, using the toolbox PSAT of MATLAB Simulink. This paper research the PLFC on the system of different solar photovoltaic systems access points, and analysis the experimental results. The results show that, under the premise of the normal operation of the ship electric power system, the improvement of the capacity of solar photovoltaic system in ship , and different access modes of photovoltaic grid-connected system, have slight impact on the power flow of power system, indicating that the photovoltaic grid-connected system in ship is stable, an appropriate increase in the capacity of PV system is feasible. The results is of certain significance of secure application of grid connected photovoltaic system in this paper.

Photovoltaic (PV) array which is composed of modules is considered as the fundamental power conversion unit of a PV generator system. The PV array has nonlinear characteristics and it is quite expensive and takes much time to get the operating curves of PV array under varying operating conditions. In order to overcome these obstacles, common and simple models of solar panel have been developed and integrated to many engineering software including Matlab/Simulink. However, these models are not adequate for application involving hybrid energy system since they need a flexible tuning of some parameters in the system and not easily understandable for readers to use by themselves. Therefore, this paper presents a step-by-step procedure for the simulation of PV cells/modules/arrays with Tag tools in Matlab/Simulink. A DS-100M solar panel is used as reference model. The operation characteristics of PV array are also investigated at a wide range of operating conditions and physical parameters. The output characteristics curves of the model match the characteristics of DS-100M solar panel. The output power, current and voltage decreases when the solar irradiation reduces from 1000 to 100 W/m2. When the temperature decreases, the output power and voltage increases marginally whereas the output current almost keeps constant. Shunt resistance has significant effect on the operating curves of solar PV array as low power output is recorded if the value of shunt resistance varies from 1000 ohms to 0.1 ohms. The proposed procedure provides an accurate, reliable and easy-to-tune model of photovoltaic array. Furthermore, it also robust advantageous in investigating the solar PV array operation from different physical parameters (series, shunt resistance, ideality factor, etc.) and working condition ( varying temperature, irradiation and especially partial shadow effect) aspects.

The contribution of solar power in electric power systems has been increasing rapidly due to its environmentally friendly nature. Photovoltaic (PV) systems contain solar cell panels, power electronic converters, high power switching and often transformers. These components collectively play an important role in shaping the reliability of PV systems. Moreover, the power output of PV systems is variable, so it cannot be controlled as easily as conventional generation due to the unpredictable nature of weather conditions. Therefore, solar power has a different influence on generating system reliability compared to conventional power sources. Recently, different PV system designs have been constructed to maximize the output power of PV systems. These different designs are commonly adopted based on the scale of a PV system. Large-scale grid-connected PV systems are generally connected in a centralized or a string structure. Central and string PV schemes are different in terms of connecting the inverter to PV arrays. Micro-inverter systems are recognized as a third PV system topology. It is therefore important to evaluate the reliability contribution of PV systems under these topologies. This work utilizes a probabilistic technique to develop a power output model for a PV generation system. A reliability model is then developed for a PV integrated power system in order to assess the reliability and energy contribution of the solar system to meet overall system demand. The developed model is applied to a small isolated power unit to evaluate system adequacy and capacity level of a PV system considering the three topologies.

Review on hybrid geothermal and solar power systems

Partial shading conditions (PSCs) can significantly reduce the output energy produced by photovoltaic (PV) systems. Moreover, when such conditions occur, conventional and advanced maximum power point tracking (MPPT) systems fail to operate the PV system at its peak because the bypassing diodes may cause the PV system to become trapped at a low power point when they are in conduction mode. The PV system can be operated at the global maximum power point (MPP) with the help of global peak searching tools. However, the frequent use of these tools will reduce the output of PV systems since they force the PV system to operate outside its power region while scanning the I-V curve in order to determine the global MPP. Thus, the global peak searching tools should be deployed only when a PSC occurs. In this paper, a simple and accurate method is proposed for detecting PSCs by means of monitoring the sign of voltage changes (positive or negative). The method predicts a PSC if the sign of successive voltage changes is the same for a certain number of successive changes. The proposed method was tested on two types of PV array configurations (series and series–parallel) with several shading patterns emulated on-site. The proposed method correctly and timely identified all emulated shading patterns. It can be used to trigger the global MPP searching techniques for improving the PV system’s output under PSCs; furthermore, it can be used to notify the PV system’s operator of the occurrence of PSCs.

The analysis presented in this paper focuses on the energetic aspects of the use of photovoltaic (PV) systems in office buildings. Energy generation from PV system has been simulated on an hourly time scale and compared with the energy demand of two office buildings located in Krakow (southern Poland). The buildings’ annual load exceeded 1 GWh in both cases. The analysis dealt with estimating how much energy generated by a PV system can be utilized on-site (self-consumption) and how big the energy surpluses will be (energy generation greater than demand). Capacities of PV systems ranging from 0.1 to 1.0 MW have been considered. Also, the impact of PV generation on the residual load parameters and changes in the maximal monthly and hourly energy demand were investigated. The results show that although the building energy demand is similar (in terms of annual volume of energy consumed) the potential of PV systems to cover it is different. The 100-kW PV system can reduce the observed hourly peak energy demand by 1% in December but by over 30% in June (respectively, from 171 kWh to 169 kWh, and from 333 kWh to 255 kWh). Considering the annual patterns of the office buildings’ energy demand and PV generation (both have their respective peaks in summer), the application of a PV system changes the office building energy demand pattern significantly from the perspective of the power system operator. After installing 500 kW PV in an office building consuming 1 GWh annually, the months with highest demand are no longer in summer but in winter.

Fault identification and detection are important to the safety, reliability, and efficiency of photovoltaic (PV) systems. Although PV systems do not have any moving parts, they are highly susceptible to harsh environmental factors and undergo degradation that increase the risk for faults. PV systems are difficult to shut down because they are always energized when exposed to any level of solar irradiation. Therefore, in the event of a fault, PV systems are dangerous to handle and have an increased risk for injury.This dissertation reviews the challenges, limitations, and improved solutions specifically for arc faults on the DC-side of the PV system. Arc faults are a subset of PV faults which occur between an air gap that may have formed from the loose connectors, junction box terminals, compromised wires, faulty soldering, and other PV degradation factors and have a large risk of causing fires in PV systems. Traditional detection methods require a priori knowledge of the PV system, utilize only a narrowband of the arcing frequencies for detection, or require large training datasets for machine learning techniques. To increase the robustness of the arc fault detection device and avoid false alarms from unwanted tripping conditions, a detailed DC arc fault model characterizing the different arc fault states as it burns in the air and a modified pink noise model corresponding to the physical arc fault states in the time-domain is proposed for detailed simulations. The unique operating point behavior of arc faults in PV systems is discussed and new current demodulation algorithm is proposed to filter the current waveform of other external noise without a priori knowledge of the PV system. An autocorrelation coefficient analysis technique is proposed which observes the entire arcing frequency band for detection analysis and simple threshold violation criteria are developed for the detection of the arc fault. The dissertation demonstrates the effectiveness of the new arc fault feature extraction methods and detection in both simulation and experimental results.--Author's abstract

Solar photovoltaic (PV) technology has the versatility and flexibility for developing off-grid electricity system for different regions, especially in remote rural areas. While conventionally straight forward designs were used to set up off-grid PV-based system in many areas for wide range of applications, it is now possible to adapt a smart design approach for the off-grid solar PV hybrid system. A range of off-grid system configurations are possible, depending upon load requirements and their electrical properties as well as on site-specific available energy resources. The overall goal of the off-gird system design should be such that it should provide maximum efficiency, reliability and flexibility at an affordable price. In this chapter, three basic PV systems, i.e. stand-alone, grid-connected and hybrid systems, are briefly described. These systems consider different load profiles and available solar radiations. A systematic approach has then been presented regarding sizing and designing of these systems. Guidelines for selection of PV components and system sizing are provided. Battery energy storage is the important component in the off-grid solar PV system. Due to load and PV output variations, battery energy storage is going to have frequent charging and discharging. So the type of battery used in a PV system is not the same as in an automobile application. Detailed guidelines for selection of battery are therefore also provided. At present, most of the world-wide PV systems are operating at maximum power points and not contributing effectively towards the energy management in the network. Unless properly managed and controlled, large-scale deployment of PV generators in off-grid system may create problems such as voltage fluctuations, frequency deviations, power quality problems in the network, changes in fault currents and protections settings, and congestion in the network. A possible solution to these problems is the concept of active generator. The active generator will be very flexible and able to manage the power delivery as in a conventional generator system. This active generator includes the PV array with combination of energy storage technologies with proper power conditioning devices. The PV array output is weather dependent, and therefore the PV power output predictability is important for operational planning of the off-grid system. Many manufacturers of PV system power condition devices are designing and developing new type of inverters, which can work for delivering the power from PV system in coordination with energy storage batteries as conventional power plant.

A comprehensive state-space model of two-stage grid-connected PV systems in transient network analysis

The effect of ambient temperature on the performance of a roof mounted Cu (In, Ga) Se2 [CIGS] photovoltaic (PV) system, which is installed in the suburb residential area of Miyazaki city, Japan, has been analyzed for the period of 2012-2017. The research work has been carried out by monitoring the variation of the performance of the PV array and PV system. The PV array and PV system with a higher ambient temperature period experience a lower performance. High ambient temperatures determine a decrease of output power performances in the same conditions of solar insolation. The results show that there is a fair negative linear relationship between ambient temperature and the performances of the PV array and PV system. A statistical analysis has also been done and the results indicate that the linear relationship between the ambient temperature and performance ratio is able to be reasonably applied, and the slope of the approximated straight lines are between -0.00230 [1/deg-C] and −0.00760 [1/deg-C]. In short, the elevating of ambient temperature contributed to the negative impact on the output performances of the PV array and PV system.

Photovoltaic (PV) generation system is an important way to promote energy transformation and to cope with environmental challenges, firstly, based on the steady-state power flow equations of the PV system AC side connected to weak grid, the influence of power grid structure parameters on their maximum transmission power is studied, which provides a theoretical basis for the design of subsequent virtual impedance; secondly, a time-domain small-signal model for PV system connected to weak grid is established, and based on the proposed small-signal model, eigenvalue analysis is employed to study the stability of PV system connected to weak grid within different grid strength. The results show that: in the case of a given SCR, the smaller the impedance angle is, the greater the maximum transmission power of the system is; when the output power of PV system is rated, the smaller grid impedance angle makes the PV system can operate under the weaker grid conditions; with the decreasing of the grid strength, the PV system prone to power oscillation Finally a virtual resistance control strategy is proposed to improve the operation stability of PV system The validity of the theoretical analysis and the feasibility of the control strategy are verified by time domain simulation.

In this paper the influence of photovoltaic (PV) power system connection on power flows and voltage stability using the DIgSILENT Power Factory software package are presented. If PV system is well dimensioned, it could improve voltage in a distribution node, but it also could have many negative impacts to the power system. There are three basic criteria for connecting a PV system to a distribution network: rapid voltage changes, high harmonic generations and flickers. The analysis was performed on a part of the real distribution system. The system consists of transformer stations 35/10 kV and 10/0.4 kV, consumers connected to low voltage level (0.4 kV), cables and overhead lines. Four cases were examined: normal conditions, connection of 10 kW PV power system, 20 kW PV power system and connection of 6 PV power systems with total power of 100 kW.

Because of the effect of weather and environment on photovoltaic (PV) array, it is hard to perform all round tests on equipment of pv generation system with the real PV array as test. So a novel pv array emulator system based on Zero-Voltage Zero-current Full-bridge converter with two diodes in series with lagging leg is put forward and a mathematical model of PV array, which use a linear model formed by the two lines, been adopted to make the control of the emulator simple convenient and reliable. In order to confirm the effectiveness of the system, the model of emulator system was established by Matlab Simulink. The result show the pv array emulator system realize to behave electrically similar to real PV array.

Photovoltaic (PV) systems incorporated with sun-tracking technology have been proposed and verified to effectively increase the power harvest. However, the actual power generated from a PV module has not been investigated and compared with that analyzed from theoretical models of the PV material. This study proposes a novel method for estimating the power benefit harvested by a two-axis sun-tracking type (STT) PV system. The method is based on semiconductor theory and the dynamic characteristics, including maximum power point tracking of PV modules that can be integrated with the database of annual solar incidences to predict the power harvested by any STT PV system. The increment of annual energy provided by an STT PV system installed at any arbitrary latitude, compared with that by a fixed-type system, can be accurately estimated using the proposed method. To verify the feasibility and precision performance of this method, a fixed-type and a two-axis STT PV system were installed at 24.92° north latitude in northern Taiwan and tested through long-term experiments. The experimental results show that the energy increments estimated by the theoretical model and actual measurement are 19.39% and 16.74%, respectively. The results demonstrate that the proposed method is capable of predicting the power benefit harvested by an STT PV system with high accuracy. Using our method, a PV system installer can evaluate beforehand the economic benefits of different types of PV systems while taking different construction locations into consideration, thereby obtaining a better installation strategy for PV systems. Copyright © 2012 John Wiley & Sons, Ltd.