- Research Article
5
- 10.1016/j.cageo.2022.105124
Adaptive ground-roll attenuation using local nonlinear filtering
- May 09, 2022
- Computers & Geosciences
- Yijun Yuan + 3 more +3
Adaptive ground-roll attenuation using local nonlinear filtering
At present, a primary challenge of seismic data processing is the ability to recognize and identify first-break seismic signals with low signal-to-noise ratio (SNR) in mountainous areas. Correlation-based supervirtual interferometry (SVI) can improve the SNR of refractions and diffractions to achieve high-quality results in velocity model construction and diffraction imaging from low SNR data. However, SVI is susceptible to coherent Gaussian noise and is limited to 2-D cases. This paper develops the cumulant-based coherent integration (CCI) method to enhance the first-break signals by using cumulant functions and multiple convolutions for both 2-D and 3-D land seismic data. The 2-D synthetic data example demonstrates that CCI can suppress coherent Gaussian noise and obtain results with higher SNR than SVI. The 3-D synthetic data example demonstrates the effectiveness of the 3-D CCI. Its application to 3-D field exploration seismic data measured in the mountainous areas of western China illustrates that the SNR of the first-break signals is much higher than that obtained by bandpass filtering, which is commonly employed in commercial software today.
Adaptive ground-roll attenuation using local nonlinear filtering
Adaptive ground-roll attenuation using local nonlinear filtering
A stable and self-adaptive approach for inverse Q-filter
A stable and self-adaptive approach for inverse Q-filter
Seismic Spectral Inversion Based on a Compressed Sensing Algorithm
Summary The seismic data spectral inversion method, arisen in recent years, can improve the resolution of seismic data for obtaining reservoir characteristics. It does not rely on prior information such as well-logging data. By using partial spectrum information from the input seismic trace data, a sparse reflectivity series can be inverted. The inverted reflectivity series can be used to improve the resolution and impedance inversion for thin layer reservoir prediction. In this paper, we implement seismic spectral inversion based on a compressed sensing algorithm, which can solve the ill-posed problem of the inversion process. In the process of inversion, we introduce a quadratic spectrum method to calculate the spectrum of seismic wavelet in the frequency domain, which can stabilize the inversion and handle real field data. Synthetic and real field seismic data examples show that the proposed spectral inversion based on compressed sensing algorithm is stable and effective. Moreover, the real field data inversion results show a good signal-to-noise ratio (SNR) and lateral continuity.
Read moreSeismic edge-preserving smoothing based on Morlet wavelet transform
Seismic edge-preserving smoothing (EPS) can suppress noise while preserving edges of important geologic natures. Edge detection is the key prerequisite for EPS. Edges are usually estimated from seismic data with full frequency, but noise often contaminates such estimate. In a recently-published paper, edges are estimated from the dominant frequency data because they have high Signal Noise Ratio (SNR), but it will bring a mismatch between the estimated edges and the real edges of different frequency data. The seismic data of different frequency has different SNR. The higher SNR data can provide higher accuracy of edge estimating. Morlet wavelet has good local performance and is suitable for decomposing non-stationary seismic signal, so it is selected to divide seismic data into several division frequency data based on multiple frequency. For the seismic data with not too low SNR, at least 2~3 division frequency data have higher SNR. When these high-SNR division frequency data are scanned, their edge information can be obtained. Then the division frequency data of that frequency and similar frequency are smoothed on the basis of the acquired edge information. To ensure the stability of the filtering algorithm, different smoothing methods are used according to whether there is an edge. The ultimate noise-removed seismic data is the combination of the smoothed division data with different frequencies. Application to synthetic model and field data shows the method can effectively reduce noise, preserve edges and preserve trackable events.
Read moreKarhunen Loeve Transform with adaptive dictionary learning for coherent and random noise attenuation in seismic data
Seismic reflection data are used by geologists to identify the best site for oil and gas explorations. The raw seismic image cannot be directly used for explorations because the noises may hinder the primary reflections and result in misinterpretations. In the proposed research work, the denoising method with adaptive dictionary learning is attempted to attenuate the coherent and random noises which affect the seismic reflections. In this method, Karhunen Loeve Transform (KLT) is combined with K-means Singular Value Decomposition (KSVD) to improve the Signal to Noise Ratio (SNR) of the seismic data. The combination of fixed transform using KLT and learning-based dictionary using KSVD remove the redundant data while retaining the necessary data for further interpretations. KLT is applied on the whole seismic image to decorrelate the coefficients and retain the primary reflections. The horizontal events in the seismic image are preserved as they represent the eigen images with large energy. The KSVD is applied to the KLT resultant data, which denoises the patch of data while simultaneously updating the dictionary. The noise is eliminated using local sparsity of the image where mutually overlapping small image blocks are learned to yield the self-adaptive redundant dictionary. It is then used to obtain the sparse representation of the image blocks by eliminating noise. The algorithm is tested for both synthetic and field seismic images, and the results indicate a better reduction of random and coherent noise with the acceptable execution time compared to other denoising algorithms used. The KLT combined with KSVD method decorrelate the seismic data from noise by preserving the primary reflections and discarding the redundant noise.
Read moreEnhancing the detection of small coal structures by seismic diffraction imaging
Enhancing the detection of small coal structures by seismic diffraction imaging
Refraction traveltime tomography based on damped wave equation for irregular topographic model
Refraction traveltime tomography based on damped wave equation for irregular topographic model
Toward an Understanding and Suppression of Coherent Noise
Despite numerous significant advances in marine streamer design, seismic data often are plagued by coherent noise with linear move out across stacked sections. Such noise is most common where the water bottom is shallow and hard. In order to suppress the noise and recover signal, it is imperative to understand the characteristics of the noise that distinguish it from signal. With that understanding, we can decide which techniques to use and at what stages to apply them in acquisition and processing. Three general categories of noise mechanisms that might produce linear noise patterns on stacked sections are examined -- direct and trapped waves that propagate outward from the seismic source, cable motion caused by the jerking action of the boat and tail buoy, and scattered energy from irregularities in the water bottom and sub bottom. Depending on the mechanism, the noise patterns as observed on shot profiles and CDP trace gathers can be entirely different from one another, and thus can be diagnostic of the dominant mechanism. Properties of field data from Alaskan waters suggest, perhaps surprisingly, that the dominant noise is from waves scattered in the shallow subsurface. This type of noise, while not dominant on the shot records, is actually enhanced by CDP stacking. The likelihood is that this type of noise is also dominant or at least competitive with surface wave noise on land seismic data. Of the many possible tools for attacking the noise, move out filtering is perhaps best for suppressing the noise while preserving signal. Our data example demonstrates that although it is more costly, the application of such filtering on the shot records is most effective because it conditions the data for the critical data-dependent processing steps of predictive disconsolation and velocity analysis. Introduction Coherent noise with linear move out across stacked sections is a frequent problem in many locations around the world. A representative section, from Alaskan waters, is shown in Figure 1. The problem as observed in marine data is, unsurprisingly, most common in areas where the water bottom is shallow and hard. In such areas, primary signal is particularly weak and contaminated by a variety of strong noises. Our goal, of course, is to suppress the noise and to recover the signal as best we can. Today's technology provides a range of tools that might be applied for the suppression. Which techniques to apply and at what stages to apply them in acquisition and processing depend on factors that we shall discuss later. Foremost in this decision is an understanding of the characteristics of the noise that distinguish it from signal. In this paper, we consider three genera categories of noise mechanisms that might produce the somewhat linear noise patterns in Figure 1. We shall demonstrate that, depending on the mechanism, the patterns as observed on shot records and on common datum- point (CDP) trace gathers can be entirely different from one another. Hence, the patterns in field data can be diagnostic of the type of noise problem present in the data.
Read moreSimultaneous Seismic Data Interpolation and Denoising Based on Nonsubsampled Contourlet Transform Integrating With Two-Step Iterative Log Thresholding Algorithm
Seismic data interpolation and denoising play vital roles in obtaining complete and clean data in seismic data processing. Seismic data usually misses along various spatial axes and always mix with random noise. In order to obtain complete and clean seismic data, reconstruction technology can interpolate missing data and attenuate random noise. Nonsubsampled contourlet transform is an effective transform to obtain multi-scale and multi-direction sparse domain data for compression sensing interpolation and denoising. However, conventional iterative shrinkage/thresholding cannot handle ill-posed and ill-conditioned equations for solving linear inverse problem. We present a two-step iterative log thresholding method to overcome ill-posed and ill-conditioned problems and improve the convergence rate and solution accuracy, which can interpolate and denoise seismic data simultaneously in the nonsubsampled contourlet transform framework. First, we use nonsubsampled contourlet transform to convert the seismic missing data with random noise to sparse domain. Then, we apply two-step iterative log thresholding algorithm to interpolate and denoise data in sparse domain. The result of each iteration is based on the results of the previous two iterations, which can accelerate convergence rate. In addition, log thresholding can further improve convergence rate and solution accuracy. Finally, we use inverse nonsubsampled contourlet transform to obtain the interpolated and denoised seismic data. The new method can reconstruct the irregularly missing data and attenuate random noise to obtain complete and clean seismic data with high accuracy, which is crucial for seismic imaging and inversion. We demonstrate the applicability and effectiveness of this simultaneous interpolation and denoising technique with successful applications to both synthetic and field data examples.
Read moreMultiscale frequency-domain seismic inversion for fracture weakness
Multiscale frequency-domain seismic inversion for fracture weakness
Decision letter: Neural markers of predictive coding under perceptual uncertainty revealed with Hierarchical Frequency Tagging
Decision letter: Neural markers of predictive coding under perceptual uncertainty revealed with Hierarchical Frequency Tagging
Read moreStatistics-Guided Dictionary Learning for Automatic Coherent Noise Suppression
Coherent seismic noise is usually difficult to attenuate due to the similar morphological patterns between noise and useful signals. To attenuate coherent noise, special preknowledge should be utilized in a state-of-the-art approach, which causes significant inconvenience. Here, we develop an automatic method to attenuate coherent noise based on the adaptive dictionary learning algorithm. The adaptive dictionary algorithm can learn the features of both signals and coherent noise and leave obvious morphological differences in the dictionary atoms. These differences in the dictionary atoms can be transformed into statistical differences, which can be measured and then used to distinguish between signal and noise atoms. We evaluate several statistical metrics in characterizing the dictionary atoms and their feasibilities in distinguishing between signal and noise atoms. We find that the kurtosis metric can best represent the differences between signal and noise atoms, and then we design a kurtosis-based filter to reject those high-kurtosis atoms and their corresponding coefficient vectors for suppressing the coherent noise. Synthetic and real data examples demonstrate the performance of the proposed algorithm.
Read moreCorrelation-Based Interferometry Method to Enhance Near-Surface Reflection Signals in Surface Active Seismic Exploration
In surface active seismic exploration, the near-surface imaging based on reflection signals provides valuable information for mineral exploration and deeper resources. However, the strong noises at near surface and stretching effects at nonzero offsets with conventional seismic data processing method severely damage the seismic reflection signals with low fold at near surface. The innovative method for the enhancement of seismic signals is the seismic interferometry method. However, due to the one-sided illumination, the seismic interferometry is still not suitable for the retrieval of reflection signals in most practical situations. In this article, we present the correlation-based interferometry (CI) method to enhance the reflection signals for near-surface imaging using the first cross correlation to construct virtual reflection signals and the second cross correlation to achieve the interferometric normal move-out (INMO) correction of the seismic reflection events with no stretching, which keeps the high resolution of near-surface reflection signals. Meanwhile, because of constructive interference stack, the CI method can significantly improve the signal-to-noise ratio (SNR) of reflection signals. The synthetic and field seismic data examples illustrate that the data-driven CI method performs better than the conventional stack (CS) method based on the velocity model for the near-surface reflection imaging.
Read moreCurvelet domain denoising based on kurtosis characteristics
Curvelet transform can be effective in eliminating seismic noise by properly setting a threshold to the curvelet coefficients. However, when the signal-to-noise ratio (SNR) of data is low, it is difficult to select a suitable threshold to remove data noise, because the curvelet coefficients are similar between signals and noise. In this paper, we propose to incorporate the kurtosis statistic representing non-Gaussian characteristics of signals into an adaptive threshold-setting scheme. Curvelet transform decomposes noisy seismic data into curvelets with different scales and directions. The kurtosis estimated from the coefficient matrix at each scale and direction is then used to weight the threshold. Therefore, the threshold difference between signals and noise is enlarged and signals will be better preserved in seismic reconstruction. Synthetic and real data examples demonstrate that curvelet selection based on the kurtosis statistic removes data noise effectively, and thus is a credible method for denoising and signal preserving of seismic data with low SNR.
Read moreVelocity-independent estimation of kinematic attributes in vertical transverse isotropy media using local slopes and predictive painting
Agood seismic velocity model is required for many routine seismic imaging techniques. Velocity model building from seismic data is often labor intensive and time consuming. The process becomes more complicated by taking nonhyperbolic traveltime estimations into account. An alternative to the conventional time-domain imaging algorithms is to use techniques based on the local event slopes, which contain sufficient information about the traveltime moveout for velocity estimation and characterization of the subsurface geologic structures. Given the local slopes, there is no need for a prior knowledge of a velocity model. That is why the term “velocity independent” is commonly used for such techniques. We improved upon and simplified the previous versions of velocity-independent nonhyperbolic approximations for horizontally layered vertical transverse isotropy (VTI) media by removing one order of differentiation with respect to offset from the imaging kinematic attributes. These kinematic attributes are derived in terms of the local event slopes and zero-offset two-way traveltime (TWTT). We proposed the use of predictive painting, which keeps all the attributes curvature independent, to estimate the zero-offset TWTT. The theoretical contents and performance of the proposed approach were evaluated on synthetic and field data examples. We also studied the accuracy of moveout attributes for shifted hyperbola, rational, three-parameter, and acceleration approximations on a synthetic example. Our results show that regardless of the approximation types, NMO velocity estimate has higher accuracy than the nonhyperbolicity attribute. Computational time and accuracy of the inversion of kinematic attributes in VTI media using our approach were compared with routine/conventional multiparameter semblance inversion and with the previous velocity-independent inversion techniques.
Read more