Time and frequency transfer using a WAAS satellite with L1 and L5 code and carrier

Both National Institute of Standards and Technology (NIST) and United States Naval Observatory (USNO) now operate a commercial 12-channel common-view receiver. The receiver tracks the GPS (Global Positioning System) satellites and the GLONASS (Global Navigation Satellite System) satellites. In this paper, we evaluate the receiver's performance using the common-clock, common-view calibration data. We also study the performance of multichannel GPS/GLONASS common-view between NIST and USNO. The common-clock, common-views using multichannel GLONASS C/A (Coarse/Acquisition) code and single-channel GLONASS P-code (precise code) contained very little transfer noise. A diurnal effect was noticed in the multi-channel GPS C/A code common-clock, common-view calibration. For the common-view comparison between NIST and USNO, the increased number of daily common-view tracks and the more precise measurements with GLONASS P-code reduced the transfer noise in short term. The multi-channel GPS/GLONASS common-view was influenced by some periodic systematic errors in long term.

A three-cornered hat analysis has been performed on three independent time transfer systems between the United States Naval Observatory (USNO) and the National Institute of Standards and Technology (NIST). These include (1) a direct Two-Way Satellite Time and Frequency Transfer (TWSTFT) link provided by the USNO, (2) an indirect TWSTFT link, and (3) GPS carrier phase (GPSCP) links. Time transfer instabilities for individual links, as quantified with the time deviation and TOTAL time deviation, have been measured for the first time for averaging periods between 2 h and 85 days. Time transfer instabilities beyond one day are roughly flicker phase in nature and generally range between 40 ps and 120 ps. Frequency transfer instabilities, as quantified by the modified Allan deviation, are observed to be as low as 1 × 10−16 for a 20 day comparison and into the mid 10−17 range at longer comparison times.

The National Institute of Standards and Technology (NIST) timescale produces a real-time realization of UTC(NIST) in the form of a pulse-per-second (PPS) time signal and a 5 MHz frequency reference. UTC(NIST) contributes to UTC (Coordinate Universal Time) using TWSTFT (Two-Way Satellite Time and Frequency Transfer) and common-view GPS (Global Positioning System) techniques. The NIST timing signal is also disseminated to the international and domestic communities using various other techniques: NIST Automated Computer Time Service (ACTS), Internet Time Service (ITS) and NIST Time Measurement and Analysis Service (TMAS). The accuracy of NIST contribution to UTC and of the dissemination of the NIST PPS time signal depends upon the quality of the calibration of the time delay between each user and the UTC(NIST) reference point. Hardware constraints, spatial constraints, and in some cases simple convenience, require that the physical input to the transfer and dissemination equipment be distributed throughout the NIST campus. A robust on-campus timing distribution and calibration system is required to ensure the accuracy and stability of these signals: for example, the current error budget for a typical time transfer calibration requires local delays to be known to an uncertainty of less than 200 ps. We utilize a clock trip calibration protocol to measure the delays introduced by the local time distribution system at NIST: a clock trip involves measuring the time difference between the UTC(NIST) reference point and a travelling clock, then transporting the travelling clock to a secondary reference point where another measurement of the time difference is performed. Clock trips are advantageous as they are a nonintrusive measurement of the full system delay. To achieve calibrations with an accuracy on the order 100 ps, we have developed a means to transport a cesium clock between remote locations on site with minimal vibration and an analysis protocol to maximize the information acquired by each clock trip. We will introduce the system used to distribute time signals at NIST, the hardware and protocol we have developed to calibrate secondary timing reference points, and data we have collected based on their implementation.

Three years ago, FAA started on an ambitious program to perform research, development and implementation of satellite navigation based on the approval and use of the DoD's Global Positioning System (GPS). One of the research and development (R&D) projects was to determine the capabilities and requirements for a GPS Wide-Area Augmentation System (WAAS), a ground-based GPS augmentation. The FAA's WAAS will consist of up to about 30 ground reference stations that will combine data to estimate separate corrections for clock and ephemeris for each monitored satellite, and also generate a correction term for ionospheric delays at lattice points on a grid formed by the intersection of lines of constant latitude and longitude. The corrections are relayed through geostationary satellites in order to reach all users in a wide geographic area. Since WAAS is expected to support Category I (CAT I) precision approaches, stringent integrity monitoring requirements will have to be satisfied. Existing single location navigation sources, such as ILSs, are monitored at a single location, whereas WAAS must be monitored at many locations and the information combined to produce a single integrity broadcast message suitable for a wide geographic area. In addition, the WAAS message includes separate differential correction components that can be individually monitored, but the integrity information must be correlated with an aircraft position error. The authors develop integrity monitoring requirements, starting with the instrument landing system (ILS), and extrapolating them for WAAS.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

We report preparations underway at the National Institute of Standards and Technology (NIST) in the United States and at the National Research Council (NRC) in Canada to support the redefinition of the international system of units (SI) and the development of a Mise en pratique for the unit of mass. NIST and the NRC possess two of the world's most precise moving coil watt balances and are developing a collaborative plan to reconcile differences between the respective measurement platforms by testing their ability to mutually realize the kilogram from the Planck constant. The important role to be played by mass metrology and new facilities, such as the NIST magnetic levitation balance and the NRC vacuum comparator, to establish the necessary link between a mass as measured in vacuum and its value in air will be considered.

Standards provide critical benefits across a wide variety of contexts, including safety and health, environmental protection, and quality of products and services. However, while these benefits are generally acknowledged, estimating the social and economic value of standards and determining how specific entities and activities influence their development require careful analysis. In October of 2018, the National Institute of Standards and Technology (NIST) asked the RAND Corporation to estimate the benefit of NIST’s research contributing to particular fire safety standards. The original objectives of the project were to (1) document the role of the NIST in the standards development process, (2) estimate the value these standards provide to society, and (3) thereby inform the economic value of NIST’s contribution to these standards. This report presents results for the first two objectives. Given that NIST’s contribution is one of several inputs combining to create these standards, NIST’s share of the credit for their value could not be quantified. Our analysis focused on case studies in standards for home smoke alarms and for protecting structures at the wildland-urban interface (WUI). Our analysis draws on a wide variety of qualitative and quantitative methods to holistically describe the impacts of these standards and NIST’s role in their development. The intended audience of this report includes those who work on fire safety research, fire safety standards, building codes, and technology transfer. The conclusions presented here may also be of interest for broader resource allocation and federal budget justification purposes. Finally, this report was written to be accessible to any interested members of the general public.

The Clean Air Mercury Rule (CAMR) which was published in the Federal Register on May 18, 2005, requires that calibration of mercury continuous emissions monitors (CEMs) be performed with NIST-traceable standards. Western Research Institute (WRI) is working closely with the Electric Power Research Institute (EPRI), the National Institute of Standards and Technology (NIST), and the Environmental Protection Agency (EPA) to facilitate the development of the experimental criteria for a NIST traceability protocol for dynamic elemental mercury vapor generators. The traceability protocol will be written by EPA. Traceability will be based on the actual analysis of the output of each calibration unit at several concentration levels ranging from about 2-40 ug/m{sup 3}, and this analysis will be directly traceable to analyses by NIST using isotope dilution inductively coupled plasma/mass spectrometry (ID ICP/MS) through a chain of analyses linking the calibration unit in the power plant to the NIST ID ICP/MS. Prior to this project, NIST did not provide a recommended mercury vapor pressure equation or list mercury vapor pressure in its vapor pressure database. The NIST Physical and Chemical Properties Division in Boulder, Colorado was subcontracted under this project to study the issue in detail and to recommend a mercury vapormore » pressure equation that the vendors of mercury vapor pressure calibration units can use to calculate the elemental mercury vapor concentration in an equilibrium chamber at a particular temperature. As part of this study, a preliminary evaluation of calibration units from five vendors was made. The work was performed by NIST in Gaithersburg, MD and Joe Rovani from WRI who traveled to NIST as a Visiting Scientist.« less

A Look at its Past Decade and a Gaze towards its Future. As the National Metrology Institute (NMI) for the United States, the National Institute of Standards and Technology (NIST), formerly the National Bureau of Standards, has provided measurement services, both calibrations and reference materials, for more than 100 years. Through these services, our customers have benefitted from our measurement capabilities and expertise in many areas, including amount of substance; dimensional metrology; electricity and magnetism; ionizing radiation; mass and related quantities; photometry and radiometry; thermodynamics; and time and frequency. NIST’s customers have also had access to some of the lowest measurement uncertainties available and a dependable way to establish traceability to the International System of Units (SI) [http://www.nist.gov/pml/wmd/metric/si-units.cfm].In response to the signing of the International Committee for Weights and Measures (CIPM) Mutual Recognition Arrangement (MRA), NIST first established an institution-wide quality system for the measurement services 10 years ago [http://www.bipm.org/en/cipm-mra/objectives.html]. NIST’s Quality System for Measurement Services has advanced the quality of service and measurements we provide our customers by fostering an environment in which NIST management and staff work towards continual improvement in the development and delivery of NIST measurement services. This paper describes NIST’s Quality System for the Measurement Services and its relevance to international standards of quality, such as the International Organization for Standardization and the International Electrotechnical Commission (ISO/IEC) 17025 standard and ISO Guide 34 [http://www.nist.gov/nistqs/]. It also provides a history of this quality system and a glimpse of future goals for improving its implementation.

An experiment to measure equatorial amplitude scintillations on the geostationary Wide Area Augmentation System (WAAS) Satellite Based Augmentation System (SBAS) signal was conducted in Cachoeira Paulista (22.70°S, 45.01°W geographic coordinates; −17.74°N, 21.74°E geomagnetic coordinates), Brazil from December 2003 through February 2004. The purpose of this paper is to estimate the scattering height of the irregularities using the WAAS signal scintillations as compared to nearby Global Positioning System (GPS) signal scintillations. Estimating the scattering height is important because the calculated zonal drift velocity of the irregularities using the measured scintillation pattern velocity on the ground is height dependent. Accurate height estimation is also required if one wishes to develop phase screen scintillation models. The difference in the pattern velocities is due to the different signal puncture point velocities with respect to the ionospheric drift. Two east‐west receivers are used to measure the scintillation pattern drift velocity and to compare the results of the geostationary WAAS satellite signal to that of a GPS satellite signal, which has a nonzero ionospheric signal puncture point velocity. By varying the assumed scattering height for the measurements from the nearby GPS signal, the zonal velocity measurements from the GPS scintillations can be matched to those of the WAAS scintillations, and a scattering height estimate can be made. When the puncture points have minimal separation, the inferred ionospheric irregularity zonal velocities should be equal. On the two nights for which data are available, scattering height estimates of 669 ± 209 km for the first night and 388 ± 139 km for the second night were obtained. On the second night, the reported mean hmF2 as calculated using a collocated Digisonde was 385 ± 17 km over the same period as the GPS/WAAS scattering height estimate. The geometry of this experiment was not optimal, but analysis demonstrates that future experiments could be substantially more accurate.

We report the results of a comparison of quantum-based AC Josephson Voltage Standards (ACJVS) between the National Institute of Standards and Technology (NIST), and the National Research Council, Canada (NRC), using a thermal transfer standard as the traveling standard. Excellent agreement was obtained between NIST and NRC from measurements on the lowest voltage ranges of the thermal transfer standard, indicating that the two ACJVS systems are consistent. This work confirms that the use of the ACJVS as a reference for ac voltage measurements is viable, and these systems can form the basis for ac voltage metrology in the future. This intercomparison was performed as part of SIM Bilateral Comparison SIM.EM-S11, AC-DC Voltage Transfer Difference at Low Voltages using an AC Josephson Voltage Standard.

As cybersecurity issues surge, it highlights the pressing need for increased awareness. In our digitally interconnected world, where information technology underpins the lives of individuals, businesses, and even national security, the threat of cyberattacks looms large. To enhance national cybersecurity preparedness, there is a critical call to action: we must promote public awareness of cybersecurity issues and bolster the ranks of trained cybersecurity professionals. This research introduces a novel cybersecurity awareness model based on the National Institute of Standards and Technology (NIST). Its primary goal is to make NIST accessible to secondary school students pursuing ICT courses and their invaluable resource, the school counselling units. The model aims to instil cybersecurity awareness in secondary school students and guide them in choosing the most suitable higher education paths, particularly in the ICT and cybersecurity fields. The study comprises three phases. In the first phase, a systematic literature review (SLR) examines globally applicable cybersecurity education models. The second phase investigates the implementation of cybersecurity education for secondary school students in Malaysia. This includes interviews with school counselling units responsible for guiding students toward higher education and surveys of students in grades four and five enrolled in ICT courses. The third and pivotal phase focuses on developing the proposed model. It involves analysing and implementing the results of the SLR, mapping them to the NIST framework, and incorporating themes from interviews and surveys. As a tangible representation of the model, a mobile application prototype has been developed. The Cybersecurity Awareness Model empowers school counselling units to seamlessly integrate career exploration with career decision-making for secondary students at any stage of their development. Moreover, it offers a means to create strategies for after-school programs, particularly in the dynamic field of cybersecurity. This model is expected to guide students in exploring academic majors and careers, preparing for higher education post-high school, initiating internships or job searches, and adapting to a world in constant flux. In doing so, it not only empowers individuals but also strengthens the nation's resilience in the face of cybersecurity challenges.

In the fall of 2019, the National Institute of Standards and Technology (NIST) funded threes studies to better understand equity and inclusivity. This report documents phase two of a three phased sequential, exploratory mixed methods study designed to provide an in-depth look at the population of NIST federal employees to identify factors, attitudes, and processes that might result in gender- specific barriers at NIST. Phase 1 analyzed human resources demographic data, compensation data, and performance data of NIST federal employees from 2011 to 2019 to determine any relevant trends. Phase 1 informed the development of an in-depth interview protocol designed to identify the differences, if any, in the ways in which men and women experience work at NIST. A total of 40 (36 female and 4 male) participants were interviewed. Three interconnected themes emerged in the data: 1) a culture at NIST that creates a Chilly Climate for women; 2) gendered experiences that contribute to and are outcomes of that chilly climate; and 3) gendered outcomes that influence women s experiences in the organization. The culture has evolved from NIST s scientific roots, scientific excellence, a strong belief in meritocracy, and as a Federal agency. Each of these characteristics contribute to a gendered social structure and the perception that change is not needed. This backdrop sets the stage for the characterizations of NIST from the interviews as a Boys Club and an Elitist environment. The radically different perspectives of men and women based in the culture result in experiences and outcomes that provide advantages and opportunities for men while erecting barriers to survival for women, including isolation and possibly exclusion. These barriers result in consequences of discrimination as well as lack of trust and resignation. Participant quotes are used as exemplars to provide details related to each of these themes. Overall, the interviews demonstrate that women and men experience a very different NIST.

The National Institute of Standards and Technology (NIST), formerly the National Bureau of Standards, was established by the U.S. Congress in 1901 and charged with establishing a measurement foundation to facilitate U.S. and international commerce. NIST provides reference materials and reference instruments that are used to ensure the accuracy, metrological traceability, and comparability of measurement results in many diverse fields of science, industry, and technology. This document provides and explains the vocabulary used at NIST to describe the reference materials and reference instruments available to NIST s customers. This document also describes the methods used in developing NIST reference materials. The definitions and descriptions provided supersede those used in the original versions of this publication, NIST SP260-136 and SP260-136-2020.

This paper presents a summary of the strategies and activities underway at the National Institute of Standards and Technology (NIST) in electronics packaging, interconnection and assembly (P/I/A). In addition, a sampling of collaborations involving these works is included. The overall NIST effort in P/I/A is composed of targeted programs conducted by the NIST laboratories and by the NIST Advanced Technology Program (ATP). A dominant aspect of the laboratory-based P/I/A program focuses on the metrology and data needed to support the product technologies envisioned within industry roadmaps. A significant aspect of the work includes efforts in metrology, materials, complex material assemblies, and microelectronic components and circuits. In parallel, the NIST ATP is supporting on a cost-share basis a variety of industry-based development projects of high-risk enabling technologies for new or improved products, manufacturing, and processes in P/I/A.

On September 5–8, 2023, the National Institute of Standards and Technology (NIST) held the second Standards and Performance Metrics for On‐Road Automated Vehicles Workshop. This four‐day virtual event provided updates on NIST’s recent work in automated vehicles (AVs) and gave stakeholders an opportunity to provide feedback and input on current and future NIST research. The workshop included high‐level keynote presentations, a series of industry keynote presentations, and NIST presentations on its current AV activities. The industry keynotes and NIST presentations were paired with breakout sessions that discussed NIST’s progress, community challenges, and stakeholder research needs in six key areas: systems interaction, perception, cybersecurity, communications, artificial intelligence, and digital infrastructure. There was general agreement that developing standards allows for better comparisons and evaluations of emerging technologies. Other key themes included: 1) Digital technologies for automation and related security/privacy concerns, including artificial intelligence, machine learning, and smart communication technologies (i.e., vehicle‐to‐vehicle (V2V), vehicle‐to‐infrastructure (V2I), and vehicle‐to‐everything (V2X)), 2) Need for standardized or common language to improve information sharing, 3) Open data sets to support and validate technical advances and standardization across system components and areas (i.e., standards evolving in parallel with technology), and 4) Pivotal role for NIST as a convener to bring diverse stakeholders together for knowledge exchange and cross‐industry dialogue.