TR-MAC

In this paper, we propose a detailed energy survey of the physical, data link, and network layer by analytical techniques. We also show the impact of regular sleep periods on node energy consumption and present a comparison analysis of single-hop vs. multi-hop communications in the energy realm. A detailed energy expenditure analysis of not only the physical layer but also the link and network layer provides a basis for developing new energy efficient wireless sensor networks. Regular, coordinated sleeping extends the lifetime of sensor nodes, but systems can only benefit from sleeping in terms of transmitted packets if the data arrival rate to the system is low. Energy efficiency is the driving motivation for it can be considered the most important factor for wireless sensor networks because of the power constraints set by battery operation. Radio solutions in the lower ISM bands are attractive because of their relatively easy implementation and low power consumption. However, the data rates of these commercial radios are also relatively low, limiting transmittable frame sizes to a few tens of octets along with strict duty cycle requirements. From the analysis we extract key parameters of selected MAC protocols and show that some traditional mechanisms, such as binary exponential backoff, have some inherent problems. We also argue that single-hop communications has up todo% lower energy consumption than multi-hop forwarding within the feasible transmission distances of an ISM radio. Index Terms-Energy efficiency, Wireless sensor net- works, Medium access control (MAC) protocols, multi-hop communications a duty cycIe (Z), (3), which is normally 10% for the 434MHz band and 1% for the 868MHz band. The duty cycle is defined as the ratio, expressed as a percentage, of the maximum transmitter on-time, relative to a one hour period. When a sensor network is expected to work continuously, this duty cycle has to be taken into account and it can affect the energy efficiency of a network. In this paper we perform cross-layer analysis by pre- senting topology, medium access control (MAC) and ra- dio transceiver energy consumption models that work in unison. The hear topology model represents a common network after network layer route discovery has been accomplished. We use an energy consumption model for the transmission and reception of MAC frames originally presented in (4), develop a coordinated sleep group energy consumption model, and analytically investigate the effect of sleep on sensor networks using three MAC protocols. From the analysis we show that although in an ideal scenario multi-hop communications perform better than single-hop communications, realistic energy models and especially the MAC protocol design have a significant impact. We propose a multi-group sleep model for our nanoMAC protocol, and show that reg- ular sleep periods have a significant, energy reducing impact on node energy consumption with low traf!fic rates. The radio transceiver energy model takes into account several important radio parameters and we use the RFM TRlOOO and RFM radio designers guide (5) for realistic transceiver parameters. The main metric used is absolute energy, consumption per useful transmitted bit. This means only the MAC or thc network protocol data unit (PDU) will be considered and all the other communicated bits, headers, control frames, preambles, etc. are considered as overhead. The rest of the paper is organized as follows. Some related work is discussed in Section IT and in Section 111 we look at the radio propagation energy model. Section TV presents the network topology and energy

Over the past few years, mobile networks have emerged as a promising approach for future mobile IP applications. With limited frequency resources, designing an effective MAC (Medium Access Control) protocol is a hot challenge. IEEE 802.11b/g/a/n networks are currently the most popular wireless LAN products on the market [1]. The conventional IEEE 802.11b and 802.11g/a specification provide up to 11 and 54 Mbps data rates, respectively. However, the MAC protocol that they are based upon is the same and employs a CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) protocol with binary exponential back-off. IEEE 802.11 DCF (Distributed Coordination Function) is the de facto MAC protocol for wireless LAN because of its simplicity and robustness [2,3]. Therefore, considerable research efforts have been put on the investigation of the DCF performance over wireless LAN [2]. With the successful deployment of IEEE 802.11a/b/g wireless LAN and the increasing demand for real-time applications over wireless, the IEEE 802.11n Working Group standardized a new MAC and PHY (Physical) layer specification to increase the bit rate to be up to 600 Mbps [3]. The throughput performance at the MAC layer can be improved by aggregating several frames before transmission [3]. Frame aggregation not only reduces the transmission time for preamble and frame headers, but also reduces the waiting time during CSMA/CA random backoff period for successive frame transmissions. The frame aggregation can be performed within different sub-layers. In 802.11n, frame aggregation can be performed either by A-MPDU (MAC Protocol Data Unit Aggregation) or A-MSDU (MAC Service Data Unit Aggregation). Although frame aggregation can increase the throughput at the MAC layer under ideal channel conditions, a larger aggregated frame will cause each station to wait longer before its next chance for channel access. Under errorprone channels, corrupting a large aggregated frame may waste a long period of channel time and lead to a lower MAC efficiency [4]. On the other hand, wireless LAN mobile stations that are defined as the stations that access the LAN while in motion are considered in this chapter. The previous paper analyzed the IEEE 802.11b/g/n MAC performance for wireless LAN with fixed stations, not for wireless LAN with mobile stations [5, 6, 7, 8, 9, 10]. On the contrary, Xi Yong [11] and Ha Cheol Lee [12] analyzed the MAC performance for IEEE 802.11 wireless LAN with mobile stations, but considered only IEEE 802.11 and 802.11g/a wireless LAN specification. So, this chapter summarizes all the reference papers and analyzes the IEEE 802.11b/g/a/n MAC performance for wireless LAN with fixed and mobile stations. In other words, we will present the analytical evaluation of saturation

Medium Access Control (MAC) protocol is one of the key network protocols that ensure Wireless Sensor Networks (WSNs) maintain high performance during communication. MAC protocol design plays an important role in improving the performances of the whole network. First, Wireless Passive Sensor Networks (WPSNs) and MAC protocols are introduced in this paper. Second, some existing MAC protocols are introduced. Sensor MAC (S-MAC) protocol is analyzed and existing improved backoff algorithms are introduced. A new MAC protocol called Improved Sensor MAC (IS-MAC) is then proposed to solve the problem that the contention window (CW) during carrier sense is fixed in S-MAC protocol. IS-MAC protocol is able to adjust CW in terms of network load, so energy consumption can be decreased. Finally, according to the simulation results on NS2, the proposed protocol has better performance in terms of throughput and energy consumption.

In this paper we propose a simple relay enabled medium access (SRMAC) protocol that enables cooperative relay transmissions. Due to the wireless signal power attenuation with distance, using a relay in a wireless network can make wireless networking more bandwidth efficient at the expense of requiring multiple transmissions for a single packet. Standard MAC protocols such as the IEEE 802.11 MAC protocol, while useable with relaying, however are not designed explicitly for relay communication. When IEEE 802.11 MAC protocol is used for cooperative communication such a relaying, each packet transmission would need to separately contend for the channel via a channel access procedure which can use significant resources (both energy and bandwidth). Because using a single relay requires two transmissions, an efficient medium access control (MAC) protocol that supports two hop transmission is needed. We introduce a protocol, SRMAC, which is a simple cooperative MAC protocol that utilizes information from the physical layer for the MAC operation of relay networks. We consider the bandwidth efficiency of SRMAC protocol considering both the physical layer and MAC layer. The SRMAC protocol includes the possibility of both cooperative transmission and direct transmission. With SRMAC, cooperative transmission (relaying) can be dynamically chosen when it is more beneficial than direct transmission. The SRMAC protocol can improve the throughput by up to 20% compared to conventional MAC protocols.

Wireless sensor “motes” is small or tiny embedded systems equipped with radios for wireless communication in the networks, which depend on batteries as a power source. The development of Medium Access Control (MAC) protocols which search is for to minimize the energy consumption in the wireless sensor network. Recent contention based MAC protocols reduce energy usage by placing the radio in a low power sleep state when not sending or receiving the message. In this paper the main emphasis is on the analysis of the Contention Based MAC Protocols and energy consumption in the networks. Based on the work done by various researchers conclude that S-MAC is the backbone of all the MAC protocols for wireless sensor networks. Our proposed work investigated the energy usage and compared the performance of IEEE 802.11 MAC protocol with S-MAC protocol on different modes like without periodic sleep and with periodic sleep on different performance metrics like Remaining Energy vs Time, Energy consumption vs global packet id and Average End to End Delay vs Time. The performance of S-MAC protocol improves on the basis of duty-cycle parameter, which determines the length of sleep period in a frame and this parameter is a variable. So changing the duty cycle will change the performance of S-MAC protocol. Finally, we have used the different routing protocol with S-MAC to evaluate the energy consumption. The experimented worked done on Network Simulator Ns2- 2.34.KeywordsMedium Access ProtocolWireless Sensor NetworkIdle listeningSleep StateS-MACEnergy ConsumptionDuty cycle

Energy efficiency is one of the important critical metrics during protocol design in Wireless Sensor Networks (WSNs). Existing Medium Access Control (MAC) protocols do not take the initial node power into consideration, which may result in unfair power consumption, especially for low-power nodes. This paper presents an energy-efficient dual-layer MAC protocol with adaptive layer duration for WSNs. The suggested MAC protocol aims to minimize the energy consumption for low-power nodes. Performance evaluation is conducted to compare the proposed MAC protocol with both Sensor-MAC (S-MAC) and Multi-Layer MAC (ML-MAC) using computer simulations. The simulation results show that the proposed MAC protocol saves energy more than both S-MAC and ML-MAC. The proposed protocol saves 66.2% and 34.1% of the energy compared to S-MAC and ML-MAC, respectively.

Security and energy efficiency are critical concerns in wireless sensor network (WSN) design. This paper aims to develop an energy-efficient secure scheme against power exhausting attacks, especially the denial-of-sleep attacks, which can shorten the lifetime of WSNs rapidly. Although various media access control (MAC) protocols have been proposed to save the power and extend the lifetime of WSNs, the existing designs of MAC protocol are insufficient to protect the WSNs from denial-of-sleep attacks in MAC layer. This is attributed to the fact that the well-known security mechanisms usually awake the sensor nodes before these nodes are allowed to execute the security processes. Therefore, the practical design is to simplify the authenticating process in order to reduce the energy consumption of sensor nodes and enhance the performance of the MAC protocol in countering the power exhausting attacks. This paper proposes a cross-layer design of secure scheme integrating the MAC protocol. The analyses show that the proposed scheme can counter the replay attack and forge attack in an energy-efficient way. The detailed analysis of energy distribution shows a reasonable decision rule of coordination between energy conservation and security requirements for WSNs.

The industrial Internet of Things (IIoT) depends on wireless sensor networks (WSNs) to enable low‐power, low‐data‐rate communication in resource‐limited settings. While the IEEE 802.15.4 standard provides the communication foundation, its medium access control (MAC) protocols face challenges including energy consumption, latency, scalability, and adaptability. Traditional MAC protocols cannot keep up with the demands of IIoT networks as the number of connected devices continues to increase. Therefore, edge artificial intelligence (Edge AI) and tiny machine learning (TinyML) represent emerging approaches that show potential for improving the performance of traditional MAC protocols directly on IIoT devices. Edge AI and TinyML allow intelligent decision‐making at the edge, which enables efficient data processing and adaptability to the environment without the need for cloud infrastructure, which may reduce latency and energy consumption. This paper systematically examines the emerging paradigm of combining Edge AI and TinyML to improve MAC protocols for WSNs in IIoT networks. We explore advanced machine learning (ML) methods applicable to resource‐limited devices, and we investigate how these methods can improve key performance metrics for MAC protocols, including energy efficiency, throughput, and network lifetime. We also discuss the challenges and limitations of applying AI solutions in WSNs, including computational constraints, data scarcity, and model scalability. Finally, we propose potential future research directions to improve the application of AI and ML techniques to develop more efficient, adaptive, and intelligent MAC protocols for future IIoT networks.

With the onset of multimedia applications, Quality of Service (QoS) in 802.11-based wireless ad hoc networks has been an essential area to look into. Standard wireless protocols such as IEEE 802.11b and IEEE 802.11e have been deemed unsuitable for multimedia traffic transmission in an ad hoc (multihop) network environment due to the unique network characteristics. As an ad hoc network is infrastructureless and distributed in nature, it gives rise to several challenges in QoS provisioning. In this thesis, we focus on the research of three key areas on QoS in ad hoc networks namely, buffer management in the medium access control (MAC) layer, cross-layer design and flow admission control. Firstly, we study MAC layer buffer management in the IEEE 802.11e protocol. The IEEE 802.11e MAC protocol provides QoS for multimedia traffic by probabilistic priority queueing. Ad hoc networks tend to generate a large volume of network control packets for route maintenance and these control packets are typically queued in the highest priority queue. As a result, higher priority control traffic is always being served, consuming most of the bandwidth and results in poor network performance for data traffic. We examine this problem and propose a dynamic buffer management scheme to mitigate it. By setting different threshold levels in different priority queues, we allow lower priority data traffic to be served when the higher priority control traffic is deemed to be excessive. Simulation of our proposed scheme has shown that our approach yielded better network performance compared to the standard protocol in terms of packet delivery ratio and average delay. Secondly, we study the cross-layer interaction between the MAC and Network layers to identify its impact on QoS. We select the IEEE 802.11e MAC protocol and Ad-hoc On Demand Distance Vector (AODV) routing protocol in our study since they are standardized protocols for wireless networks. In IEEE 802.11e MAC protocol, lower priority traffic has a higher probability of being blocked. Hence, the MAC layer will inform the Network layer of a broken link through the link notification function. In this case, AODV will re-route the paths that traverse this link. As a result, higher priority traffic which shares the same link as the lower priority traffic will undergo the same re-routing procedures. We termed this phenomenon path correlation effect. Under high traffic load, the path correlation effect will be more intense and hence degrade the QoS of higher priority traffic. To break the path correlation effect, we propose a cross-layer design called the Bundled Virtual Circuit (BVC). Our proposed BVC scheme not only addresses the path correlation issues, but also provides priority treatment from the Network layer to the MAC layer. Through our simulations, our proposed cross-layer design approach is proven to provide better network performance than the 802.11e/AODV protocols in terms of packet delivery ratio and delay. Finally, we examine flow admission control at the routing layer in ad hoc networks. Standard routing protocols such as AODV performs routing on a shortest path basis. In the presence of multiple routes, hotspots are likely to form among the intermediate nodes and thus lead to network congestion. In addition, existing routes are not well-protected from the introduction of new routes. We propose a flow admission control algorithm to be used with AODV. Our algorithm allows routes to be created through available bandwidth and congestion estimation. During the route discovery phase, each node will be gauged on its estimated available bandwidth and its backlog of packets in the MAC buffer. If a node does not have sufficient bandwidth, or has too many backlogged packets compared to the requested flow rate, it will not participate in the route discovery process. From simulations, our new scheme is able to provide better network performance than the standard AODV protocol in terms of delay. Our work in this thesis focuses on QoS provisioning in ad hoc networks from the MAC and network layer perspectives. By studying the network characteristics and protocols’ behavior, we investigate the various problems of providing QoS in an ad hoc network environment and propose three different schemes to improve the QoS provisioning at the MAC and network layers. We believe that our work is able to provide some insights to the research area on QoS in ad hoc networks.

Power efficient ultra-wideband based wireless communication for wireless body area network applications

Medium access control (MAC) protocols provide a means to nodes to access the wireless medium efficiently and collision free to the best of their ability. In this paper we provide a survey of MAC protocols developed for mobile ad hoc (MANETs) in the past based on certain methods and techniques such as multiple radios, multiple channels and specialized beamforming antennas. We discuss some of the MAC protocols designed for wireless sensor networks (WSNs) and their applicability in a MANET environment. There are some similarities between MANETs and WSN's in general but there is also critical differences between the two that affect the design of MAC protocols for both these networks. Traditionally, MAC protocols have been classified on the basis of two broad categories of contention free and contention based MAC protocols but a number of new algorithms proposed in the recent past merge the two schemes together in a single MAC solution and thus there is a need for a new classification approach. MANETs have their unique constraints and characteristics. In this classification, we will discuss various MAC solutions proposed in the past in the light of these constraints and characteristics. We do not intend to explain each and every protocol since the number of MAC solutions proposed in the past decade or so is very large. The purpose of this article is to give the readers a general idea on the various techniques and methods used in literature to develop MAC protocols for MANETs. The techniques range from algorithmic changes such as cross-layer design to enhancement in hardware such as directional antennas.

A joint MIMO-OFDM transceiver and MAC design for mobile ad hoc networking

With the increasing demand for marine exploration, underwater acoustic sensor networks (UASNs) are prone to have the characteristics of large-scale, long term monitoring, and high data traffic load. Underwater media access control (MAC) protocols, which allow multiple users to share the common medium fairly and efficiently, are essential for the performance of UASNs. However, the design of MAC protocols is confronted with the challenges of spatial unfairness, data eruption, and low energy efficiency. In this paper, we propose a novel data concurrent transmission (DCT) MAC protocol, which is able to exploit long propagation delay and conduct concurrent transmission. Specifically, we present the theoretical performance analysis of the proposed MAC protocol in detail and give an analytical solution of the success concurrent transmission probability between nodes. In addition, simulation results are provided to demonstrate that our proposed protocol is appropriate for UASNs and can significantly improve the performance in terms of network throughput and energy consumption. Finally, we give some typical future applications of UASNs and discuss the demands on MAC protocol design.

Since cognitive wireless network (CRN) has the characteristic of secondary use, it can enable the device to dynamically access available spectrum without interference to primary users (PUs), which can effectively alleviate contradiction between the lack of spectrum resources and the growing demand for wireless access. However, Medium Access Control (MAC) protocol as CRN core components, can achieve competition access of the licensed spectrum and coordination control, which will maximize spectrum utilization efficiency and network throughput. The contribution of this survey is threefold. First, we analyze the characteristics of the existed multi- channel MAC protocol in CRN; Second, according to the different ways of spectrum access in CRNs, the multi-channel MAC protocols are classified into time-slotted based MAC protocol, control channel based MAC protocol and hybrid MAC protocol, and the paper emphatically analyzed the advantages and disadvantages of these multi-channel MAC protocols; Finally, the paper explores the difficulties and the challenges of multi-channel MAC protocols design in cognitive wireless network.

The properties of underwater acoustic channel are quite different from those of terrestrial wireless sensor networks, which brings many challenges to design an efficient media access control (MAC) protocol for underwater acoustic sensor networks (UWASNs). In order to overcome the long propagation delay and the funneling effect of UWASNs, a MAC protocol, named path-oriented code assignment (POCA) CDMA MAC (POCA-CDMA-MAC) protocol, is proposed in the paper. In the proposed protocol, a round-robin method and the CDMA technology are used to make the sink receive packets from multiple neighbors at the same time. Unlike other CDMA-based protocols using the transmitter-oriented code assignment (TOCA) or the receiver-oriented code assignment (ROCA), the POCA is used in the CDMA technology. Since the number of the path is much less than the number of nodes, the length of the spreading code used in systems with POCA is greatly shorter than those of the spreading code used in systems with TOCA or ROCA. Simulation results show that compared to existing MAC protocols for UWASNs, the proposed MAC protocol achieves a higher throughput, and a lower end-to-end delay.