Unwrapping multiple co-channel interference signals

In this contribution, we present a linear multiple-input multiple-output (MIMO) equalization scheme at the receiver side for high-speed electrical chip-to-chip communication. As opposed to traditional single-input single-output (SISO) equalization per lane, this MIMO approach enables cooperating receivers to treat crosstalk (XT) between neighboring channels as an information-bearing signal instead of a disturbing signal, allowing to mitigate both inter symbol interference and XT. Given a simulated 4 × 4 MIMO electrical chip-to-chip interconnect channel, we point out that, for a given total number of equalizer taps, MIMO equalization can outperform SISO equalization. Moreover, by further increasing the total number of equalizer taps, MIMO equalization allows to obtain performance gains that are substantially larger than for SISO equalization.

In this work, we propose to design and subsequently analyze the performance of a power non-orthogonal multiple access (power-NOMA) system, having multiple input multiple output (MIMO) antennas with the consideration of various imperfection statistics. Three key issues emerge, while NOMA is in place. The first one is the user order mismatch due to estimated channel, which impacts the NOMA performance. The second one is the imperfect successive interference cancellation (SIC) at the receiver, which impacts the interference cancellation at the NOMA receiver. The third issue is the imperfection arising due to hardware circuits, which include fixed-pointed digital logic, analog and radio frequency (RF) circuits. To some extent, these issues have been addressed in bits and pieces in the context of single antenna power NOMA design, however they have not been addressed all together in the context of MIMO power NOMA. There are several key contributory aspects in this work. Key part is the exploitation of these parameter estimation error statistics along with the imperfections in transceiver hardware chains and SIC at the receiver. We propose a MIMO NOMA based on the maximum sum-rate criterion. An analytical framework has been presented in this regard. Numerical results demonstrate that the consideration of these error statistics improves the overall sum-rate performance.

High-order modulation formats with high symbol rates are promising candidates for meeting the growing traffic requirements of digital coherent transmission. In using these modulation formats, the impact of transceiver impairment on the signal quality becomes significant. In this paper, we propose an 8×2 widely linear (WL) multiple-input multiple-output (MIMO) equalizer with independent complex filtering on IQ signals to mitigate linear transceiver impairments. Furthermore, we extend the equalizer for digital subcarrier (SC) multiplexing. Accordingly, a 16×4 WL MIMO equalizer is also proposed to mitigate linear transceiver impairments, through application to a pair of SC inputs. Experimental results show that, for transmission of a 58-GBaud polarization-multiplexing 64 quadrature amplitude modulation (PM-64QAM) single-carrier signal, the proposed method effectively compensates for various receiver impairments and also mitigates transmitter (Tx) impairments. Q-penalties of 0.1 dB up to a 10-ps skew, 2.5-dB gain imbalance, 7.2-degree phase error, and –15-dB crosstalk in Tx were achieved for 100-km standard single-mode fiber transmission. Moreover, for a 29-GBaud PM-64QAM dual-SC signal, the proposed 16 × 4 WL MIMO equalizer shows transceiver impairment mitigation performance similar to that in the single-carrier case, even though dual-SC transmission is less tolerant of laser phase noise.

Precoding for multiple-input multiple-output (MIMO) spatial multiplexing generally requires high feedback overhead and/or high-complexity processing. Simultaneous reduction in transmitter complexity and feedback overhead is proposed by imposing a diagonal structural constraint to precoding, i.e., power allocation. Minimum bit-error rate (MBER) is employed as the optimization criterion, and an approximate MBER (AMBER) power-allocation algorithm is proposed for a variety of receivers, including zero-forcing (ZF), successive interference cancellation (SIC), and ordered SIC (OSIC). While previously proposed precoding schemes either require ZF equalization for MBER, or use a minimum mean-squared error (MMSE) criterion, we provide a unified MBER solution to power allocation for ZF, SIC, and OSIC receiver structures. Improved error-rate performance is shown both analytically and by simulation. Simulation results also indicate that SIC and OSIC with AMBER power allocation offer superior performance over previously proposed MBER precoding with ZF equalization, as well as over MMSE precoding/decoding. Performance under noisy channels and power feedback is analyzed. A modified AMBER algorithm that mitigates error propagation in interference cancellation is developed. Compared with existing precoding methods, the proposed schemes significantly reduce both transmit processing complexity and feedback overhead, and improve error-rate performance

Wireless network is one of the most important things in the development of telecommunication. However, the existing wireless technology has not been able to efficiently create a very high data rate because it was very sensitive to fading. Therefore, Orthogonal Frequency Division Multiplexing (OFDM) technology combined with MIMO (Multiple Input Multiple Output) transceiver system was used to gain more diversity and bandwidth efficiency. The propagation performed on the OFDM MIMO system was multipath propagation. To reduce Intersymbol Interference (ISI) was used Zero Forcing (ZF) equalizer which works by combining channel response and equalizer response itself to eliminate ISI. This study aims to determine the effect of Zero Forcing Equalizer on OFDM MIMO system using rayleigh fading channel and compared the result with OFDM MIMO STBC system. The research method used was simulation using MatLab R2015a. The simulation results showed that the performance of OFDM MIMO ZF system was worse than OFDM MIMO STBC system i.e BER vs EbNo simulation, eye diagram simulation, and constellation diagram simulation. The OFDM MIMO ZF system was required an Eb / No value more than 25 dB to achieve BER 10-4 while the OFDM MIMO STBC system only required an Eb / No value of 10.5 dB to achieve BER 10-4. The eye pattern generated by the OFDM MIMO ZF system was more closed and the dispersion of constellation signals away from the ideal point while OFDM MIMO STBC system displayed a more open eye pattern and the dispersion of its constellation signal closer to the ideal point. It indicated more ISI occurs in the OFDM MIMO ZF system than that in OFDM MIMO STBC system.

Beamforming (BF) technique in cooperative multiple input multiple output (MIMO) antenna arrays improves signal to noise ratio (SNR) of the intended user. The challenge is to design transmit beamforming vectors for every user while limiting the co-channel interference (CCI) from other users. In this paper, we proposed cooperative beamforming based on Signal-to-Leakage Ratio (SLR) to exploit the leakage power as a useful power in the second time slot after user cooperation, for this purpose successive interference cancellation (SIC) is employed in each user to separate the leakage signal from the desired signal. Without increasing the complexity, Maximizing Signal-to-Leakage Ratio (SLR) subject to proposed power constraint instead of a unity norm is the way to achieve extra leakage power. To reduce the erroneous, Bose–Chaudhuri–Hocquenghem (BCH) codes employed in Beamforming of (SIC) cooperative scheme BF(CS-SIC-BCH). Maximum-likelihood (ML) estimator method is used at each user receiver. Simulation results show that the performance of the proposed scheme BF (CS-SIC-BCH) over Rayleigh and Rician fading channel is significantly better than the performance beamforming based on SLR in Non-cooperative system. More specifically to achieve a BER of about the required SNR for the proposed scheme is about 1 dB less than the Non-cooperative system.

Ever since the adoption of the single carrier frequency division multiple access (SC-FDMA) scheme for the uplink in the Long Term Evolution (LTE) standard, there has been much interest in improved receiver algorithms for the same. Successive interference cancelation (SIC) based turbo receivers (Turbo SIC) have been proposed to tackle the multi-stream interference (MSI) for transmission modes such as spatial multiplexing (SM) and multiuser (MU) multiple input multiple output (MIMO). In addition, decision feedback equalizers (DFE) have been discussed as an alternative to the simple linear minimum mean square error (LMMSE) based receivers to suppress intersymbol interference (ISI) caused by the frequency selective multi-path channel. This paper proposes a DFE receiver variant based on parallel interference cancelation (PIC) with maximum likelihood detection (MLD) and ordered SIC (OSIC) principles to suppress ISI and MSI. Simulations show that the proposed receiver performs better than the existing SIC and DFE based receivers and achieves the matched filter bound (MFB) for both coded and uncoded systems.

In this paper, anew iterative interference cancellation multiuser detection (MUD) method is proposed for overloaded multiple-input multiple-output (MIMO) coded orthogonal frequency division multiplexing (OFDM) systems. In the first iteration, a channel analyzer and selector are employed, which ensure that non-convergent channels are not used. Then low complexity RAKE reception is applied, and a successive interference cancellation (SIC)-based approach is used such that the strongest user is decoded first. In each iteration, the soft output of the convolutional decoder is fed back to cancel inter-user interference using parallel interference cancellation (PIC). The simulation results show that, this technique can achieve near-optimum bit error rate (BER) performance, and optimum frame error rate (FER) performance, with lower complexity than optimum maximum likelihood (ML) methods at the cost of 4% of channels rejected.

In this paper, modeling and simulation of a receiver with interference cancellation technique for the downlink transmission of multiple input multiple output (MIMO) multicarrier code-division multiple access (MC-CDMA) based cognitive radio is investigated. Synchronous transmission of multiple users’ signals over frequency selective Rayleigh channel is considered. Linear MMSE frequency domain equalization is utilized to overcome channel effect. Orthogonal Variable Spreading Factor (OVSF) codes are used to support users of different data bit rates. An adaptive subcarrier deactivation method is proposed for deactivating a set of subcarriers used for downlink transmission by the cognitive radio base station that overlap with primary user’s transmission in order to avoid causing interference to the primary user. Orthogonality between the spreading codes is lost due to subcarrier deactivation which causes interference among secondary cognitive radio users. In this paper a modified Group-wise Successive Interference Cancellation (m-GSIC) technique is proposed to suppress the interference caused due to subcarrier deactivation. The simulation results show that the proposed interference cancellation technique results in better BER performance over conventional interference cancellation techniques

This paper investigates the performance of IEEE 802.11ac physical layer (PHY) when the following multiple input multiple output (MIMO) detectors are implemented: Sphere Decoding (SD); QRM-Maximum Likelihood (QRM-MLD); List Minimum Mean Squared Error Successive Interference Cancellation (List MMSE-SIC); List Zero-Forcing SIC (List ZF-SIC); Lattice Reduction MMSE-SIC (LR MMSE-SIC) and List LR MMSE-SIC. The conclusions are founded on simulation results, validated using first order techniques, over TGac channel models. The IEEE 802.11ac simulator implements hard-decision Viterbi decoding and realistic synchronization and channel estimation algorithms. The List MMSE-SIC scheme presents power gains around 2 dB in relation to the List ZF-SIC MIMO detector. The QRM-MLD MIMO detector has a highly superior performance regarding to the List MMSE-SIC MIMO detector since this latter scheme cannot overcome the propagation errors that degrade the performance of MMSE-SIC MIMO detectors. However, for moderate list lengths of 4 and 8, the QRM-MLD MIMO detector presents severe power losses in relation to the optimal SD MIMO detector. The LR MMSE-SIC MIMO detector allows power losses of only 1–2 dB in reference to the optimal SD MIMO receiver. There are no noticeable power gains when List detection techniques in MMSE-SIC MIMO detectors are implemented since the diversity gains due to implementation of LR basis change overcome the error propagation in SIC MIMO detectors with original channel basis.

A improved algorithm to perform channel estimation and equalization for multiple input multiple output(MIMO) systems in frequency and time-selective fading environments is put forward. lt contains two steps: training and tracking. In training phase, improved Kalman filtering, namely robust Kalman filtering(RKF), is exploited to estimate channel impulse response(CIR). After that, in tracking stage,the RKF and minimum mean-square error feedback decision equalizer (MMSE-DFE) cooperate to track the time-varying channel. The RKF recursions is presented and a closed-form solution for baud rate MIMO MMSE-DFE under perfect knowledge of CIR and correct past decisions conditions is derived. In addition, it regards unknown dc-offset due to zero intermediate frequency(IF) at the receiver as the mean of measurement noise, which is estimated as a byproduct through robust Kalman filters. Finally, it is compared with well-known ones,such as least mean-square (LMS), recursive least square (RLS), Kalman filtering (KF). All these show that the proposal exhibits better performance.

Recent demand for capacity increase in mobile communications urges the development of both multiple- input multiple-output (MIMO) and small cells. However, overlapping coverage areas between neighboring small cells results in interference-limited networks, where the capacity of the network is severely degraded without superior intercell interference management (IIM) techniques. As one of the superior IIM techniques, the power control intercell interference coordination (ICIC) optimizes downlink transmit powers in the network. This paper proposes an IIM scheme consisting of both neural networks (NNs) power control on the transmitter side and interference cancellation (IC) on the receiver side. Computer simulations examine networks of MIMO systems with the power optimization using some ICIC algorithms: NN, the greedy search, the belief propagation (BP), and the maximum power, combined with IC on the receiver side. In addition, the deep learning, a breakthrough technique for NN with multi-layer structures, is also applied to mobile communications. The results show that the performance of NN is very close to that of the greedy search and superior to that of BP. Complexity of NN is much less than that of BP, and thus NN is suitable for IIM. It is also demonstrated that employing IC provides high capacity gain.

The multiuser detection is a signal processing tech- nique which enhances the performance and capacity in DS- CDMA technology. Since its complexity issue was too expensive to handle, there was focus on the suboptimal detectors. In this paper we propose a hybrid method called adaptive differential interference cancellation method (ADIC) which is a hybrid of the differential interference cancellation method and which is then combined in a adaptive way to determine a weight matrix which will map the outcome of the differential interference cancellation method to come out with a better performance. This paper also looks into the computational cost of different methods using the floating point operation (flops) which is a good estimation of the comparative computational cost if not the exact one. I. INTRODUCTION The conventional DS-CDMA match filter detector fails to combat these issues due three prominent drawbacks: unrealis- tic ucorrelated code, near-far problem (even with strict power control (1)), and tough multiple access interference (MAI). Many advanced signal processing approaches have been made to improve the performances of these kinds of detectors. In this paper we will study the different approaches that were made in this field and implement these methods to reach a conclusion about the detection methods. As the name of the topic suggests the focus of our work will be study and propose cost effective better performing multiuser detection method. We will explore Multiuser Detection Techniques in Synchronous CDMA environment. Multi-user detection deals with the development and ap- plication of joint demodulation and interference cancellation cancellation techniques for improved detection of a desired set of digital signals in the presence of multiple access interfer- ence, intersymbol interference and noise. Since veterbi forward dynamic algorithm (2) is used in case of Optimum multiuser detection (3) the complexity grows in with the increase in the number of users. Hence the complexity is immense which increases exponentially with the increase in the number of users. Looking ahead for lower complexity hence lesser cost of implementation, the paper proposes the use of sub-optimal linear detectors (4). The sub-optimal detector the paper next focuses on is Decorrelator type of Detector (5) which is optimal in least squares. This detector out performs the optimal detector in many respects. Then the Minimum Mean Square Error (MMSE) linear detector is proposed which tries to minimize the squared error from the required transformation. It is one of the most popular detectors in use due to its easiness to implement and its lower complexity. But then in the above detection methods the decisions made were based on certain linear transformation criterion and there are missing efforts to check the performance in between the detection process to improvise the transformation method better detection. So then the paper proposes Adaptive multiuser detection. Then the paper focuses on Interference cancellation methods which utilize the feedback to reduce Multiple Access Interference (MAI) in the detected bits. Under the Interference Cancellation umbrella the Successive Interference Cancellation (SIC) (6), (7) method is explored and simulated to observe the results. Then the next method which performs better than SIC and more commonly used in real life, called Parallel Interference Cancellation (PIC) (6), (8) is also implemented. Before going ahead to implement the final proposed detection method, this paper implements Differential Interference Cancellation (DIC) (9) method. And then this paper finally proposes an Inter- ference Cancellation method called the Adaptive Differential Interference Cancellation Multiuser Detection method which is cost effective in comparison to other Interference Cancellation methods as we will require lesser hardware (multipliers as in the SIC or Parallel Interference Cancellation (PIC)) for that matter. More ever since we are using adaptive method the desired BER can be further reduced. This proposed method will be discussed in detail in the following section.

Single carrier frequency division multiple access (SC-FDMA) is adopted as uplink multiple access scheme in 3G long-term evolution (LTE). Combining SC-FDMA with MIMO (multiple-input multiple-output) can increase capacity and throughput but detection technique is required at the base station (BS). Interference cancellation (IC) based on cyclic redundancy check (CRC) is a conventional detection algorithm. In this paper, we divide IC into useful IC and useless IC. Simulation results indicate that CRC-based IC algorithm performs too many useless ICs, which increases the complexity. Thresholded IC algorithm is proposed to reduce the complexity. In the proposed algorithm, IC is performed only when the probability that the IC is useful exceeds a threshold. We select 0.5 as the threshold. With the threshold, the proposed algorithm reduces the complexity significantly and keeps the performance loss negligible.

In DS/CDMA systems, overcoming near/far effects and fading is imperative for satisfactory performance. One way to combat the near/far effect is to use stringent power control, as is done in most of the commercial systems. Another approach is Multi-User Detection (MUD). In addition to mitigating the near/far effect, MUD has the more fundamental potential of raising capacity by canceling Multiple Access Interference (MAI). This paper analyses the convergence behavior and performance of successive interference cancellation (SIC) for CDMA systems. This analysis will be generalized for Parallel Interference Cancellation (PIC) also. In this paper a Hybrid Interference Cancellation (HIC) receiver is designed by combining the successive and Parallel Interference Cancellation algorithms, so that the advantages of both the schemes are utilized effectively. The Hybrid Interference Cancellation scheme results in a simple, faster and reliable receiver. With the help of simulations, it is shown that this hybrid approach outperforms the other Multi-User Detection schemes.