Wi-cache: Towards an SDN based distributed content caching system in WLAN

In recent years, the wireless local area networks (WLAN) access points (APs) are being deployed rapidly in the offices and the campuses to satisfy the quality of service (QoS) requirements such as network bandwidth. However, many empirical studies show that a large fraction of idle WLAN resources result in the significant energy losses. To reduce the energy consumption without violating the QoS requirement, we propose a QoS-aware AP energy saving mechanism using software defined network (SDN). We leverage the capability of the SDN controller to dynamically monitor the network condition information to estimate the network bandwidth requirement of the devices and then manage the network forwarding to provide seamless handover. Our experimental results show that the proposed scheme can effectively reduce the number of power-on WLAN APs while still providing QoS guarantee, such as network bandwidth and handover cost.

Throughput maximization in a network is one of the major key challenges in wireless LANs (WLANs) and it could be achieved when the load of access points (APs) is balanced. The AP load in WLANs is very often found to be uneven. To overcome such imbalance of load, a load balancing technique have been proposed. The load balancing techniques commonly require proprietary software or hardware at the user side for controlling the user-AP association. A new load balancing technique by controlling the size of WLAN cells (i.e., AP’s coverage range), which is conceptually similar to cell breathing in cellular networks. The proposed scheme does not require any modification from the user side nor may any changes be required to the IEEE 802.11 standard [1]. It only requires the ability of dynamically changing the transmission power of the AP beacon messages. We develop a newer load balancing algorithm that will find the optimal beacon power settings which will thereon help to minimize the load of the most congested AP. The load may become shared and this may be performed with minimal delay and also maximized throughput is to be achieved. Keywords: Network throughput, Access points, WLAN, Beacon Messages, Load balancing, Throughput, Wireless LANs.

Traffic diversion and load balancing are critical issues in Wireless Local Area Network (WLAN), such as Wi-Fi. When multi hop ad-hoc nodes are introduced between two WLANs, the performance becomes more inevitable, which brings new challenging issues, such as how to reduce the packet dropping rate, end-to-end delay, how to control traffic in more dense WLAN, how to take more advantage of multi hop relay nodes for better resource management. In this paper we proposed a traffic diversion scheme for high dense Infrastructure based WLAN. This proposed scheme consists of two parts. In the first part, we have focused on Access Point (AP) selection policy, which utilizes multi-hop adhoc nodes to divert traffic of high dense AP to less dense AP with non-overlapping coverage. In the second part, we provided a framework for routing scheme in multi hop ad-hoc nodes for exchange of information. Ongoing ns2 simulations demonstrate that the scheme that we proposed is more effective than traditional one in terms of packet drop and end to-end delay.

The IEEE 802.11 Wireless Local Area Network (WLAN) specification defines two ways to configure a wireless network：infrastructure mode and ad-hoc mode. The infrastructure mode includes an access point (AP). APs connect between wireless LAN and wire LAN. Before a station is allowed to send a data message via an AP, it shall first become associated with the AP. Based on the measured SNR from the probe response packets received from each AP, the station will then select the best AP for authentication and association. After a station is associated with an AP, it will wait until the signal of the AP drops to a threshold and start to rescan for new AP’s. In this thesis, we present a new handoff scheme for 802.11. Station estimates the channel quality periodically and piggybacks its channel information with the transmission packet. After AP receives the information, it has a complete picture of the channel utilization. Then AP uses SyncScan mechanism to send the channel quality information to the sataions with the Beacon frame. When a station wants to associate with a new AP, it will use the information it received and choose the AP with low channel utilization.

Recent demands on affordable, portable wireless communication and computation devices have resulted in exponential growth of wireless networks ranging from Wireless Local Area Networks (WLAN) and Wireless Wide Area Networks (WWAN) to Ad-Hoc and Sensor networks. The major goal of wireless communication is to allow users to communicate together and to have access to global network anytime anywhere. This has led to wide acceptance of infrastructure based cellular networks (WWANs) where mobile stations communicate with a centralized controller, often referred as Access Point (AP) that is connected to the wired networks. On the other hand, WLANs have appeared as dominant popular technologies in many venues including a local area such as an academic campus or an airport terminal. These wireless networks mostly rely on IEEE 802.11 Wi-Fi (Wireless Fidelity) technology and its various derived versions (i.e. 802.11a,b,g). IEEE 802.11 standard supports two operational modes: The infrastructure-based Wireless Local Area Networks (WLANs) and an infrastructure-less Ad-Hoc Networks. A WLAN (Conti, 2003) typically imposes the existence of an AP and normally is connected to the wired networks to provide internet access for mobile devices. Obviously, only one hop link is needed to communicate between mobile devices and AP. In contrast, there is no AP or infrastructure in Ad-Hoc networks. Any two stations can communicate directly when they are in the range of reception of each other. To this end, the stations may use multi-hop routing to deliver their packets to destinations. The ad-hoc protocols (Conti, 2003; Mohapatra & Krishnamurthy, 2005) are self-configured for address and routing in the face of mobility and the network topology may change in each configuration. The multi-hop wireless ad-hoc networks, or multi-hop wireless networks enable wireless networking in the environments where the wired or cellular connections are impossible, inadequate, or cost effective (e.g. battle field, disaster recovery, etc.). The popularity of internet over the last decades has resulted in rapid advancement of demanding applications. The Transmission Control Protocol/Internet Protocol (TCP/IP) (Stevens, 1994) is a well-known de facto protocol in developing today’s internet. Basically, TCP provides a connection-oriented and reliable end-to-end data delivery between two hosts in traditional wired networks. Since TCP is well tuned and due to its wide acceptance in internet, it is desirable to extend and adopt its functionality to wireless networks. On the

Queueing systems to study the energy consumption of a campus WLAN

The massive growth of data consumption and the variety of wireless technology emergence has made the handover (HO) an attractive research topic nowadays, mainly due to the popularity of Wireless Local Area Networks (WLANs), which allow users to reach high-speed data communication while they are in movement. Moreover, mobile devices such as tablets and smartphones have also become increasingly popular due to their low cost and ease of use, and an increase in mobile device use is expected to accelerate in the coming years, along with the availability and use of applications such as real-time services and online gaming. The traditional HO methods will likely not meet the requirements of mobile devices for modern applications due to the lack of intelligence, lack of awareness Quality of Service (QoS) and Quality of Experience (QoE) requirements of mobile users. We, therefore, introduce a novel architecture that supports horizontal HO in homogenous networks. This architecture is based on the Software-Defined Wireless Networking (SDWN) concept, where the wireless network is controlled centrally and the wireless Access Points (APs) are programmable. In this architecture, HO algorithms will assist wireless users to find the network that could best support the application requirements through Quality of Service (QoS) and Quality of Experience (QoE) management policies. The first HO algorithm proposed in this thesis is called Quality of Experience Oriented Handover Algorithm. This algorithm will guarantee the best possible connectivity to the users in terms of their QoE and QoS requirements and outperforms the traditional methods in a sparse network environment. The second contribution is called Optimised Handover Algorithm for Dense WLAN Environments. This algorithm has been designed to address dense network environments via taking into consideration the Adaptive Hysteresis Value (AHV). The AHV will help the Optimised Handover Algorithm via reducing the so-called ping-pong effect. This contribution shows promising performance results by selecting the best candidate AP, decreasing the number of redundant HO and avoiding the ping-pong effect. The final contribution is called Priority Based Handover Algorithm. We extended our proposed SDWN architecture in order to include the concept of prioritising users and make a smart decision during the process of HO. This algorithm will prioritise a certain class of users to avoid the effect of the over-congestion. The results show that the approach based on priority outperforms the state of the art and provides better QoE to the high priority users despite the over-congestion situation.

The growing usage of wireless devices has significantly increased the need for Wireless Local Area Network (WLAN) during the past two decades. However, security (most notably authentication) remains a major roadblock to WLAN adoption. Several authentication protocols exist for verifying a supplicant's identity who attempts to connect his wireless device to an access point (AP) of an organization's WLAN. Many of these protocols use the Extensible Authentication Protocol (EAP) framework. These protocols are either vulnerable to attacks such as violation of perfect forward secrecy, replay attack, synchronization attack, privileged insider attack, and identity theft or require high computational and communication costs. In this paper, a lightweight EAP-based authentication protocol for IEEE 802.11 WLAN is proposed that not only addresses the security issues in the existing WLAN authentication protocols but is also cost-effective. The security of the proposed protocol is verified using BAN logic and the Scyther tool. Our analysis shows that the proposed protocol is safe against all the above attacks and attacks defined in RFC-4017. A comparison of the computational and communication costs of the proposed protocol with other existing state-of-the-art protocols shows that the proposed protocol is lightweight than existing solutions.

There has been widespread deployment of IEEE 802.11 wireless local area networks (LANs) because of high demand from mobile terminals, such as iPod and Android terminals. With the increasing energy consumption of the wireless LANs, the development of power saving technologies incorporated into the wireless LANs have become important. In wireless LANs, access points (APs) continuously consume the power regardless of the communication. Therefore, we have proposed the Radio-On-Demand (ROD) wireless LAN, which provides power saving schemes on the basis of the utilization of wireless LANs. In this study, we particularly focus on the power saving scheme of the APs, and propose the decentralized association management of ROD wireless LANs. In our scheme, an AP assigns associated stations (STAs) to new APs before switching to sleep mode. Simulation results show that the proposed scheme can realize sufficient power saving.

In wireless local area networks (WLANs) made up of Extended Service Sets, access point (AP) selection is a key issue to improve the network performance and balance the traffic load. WLANs operating in the shared Industrial, Scientific and Medical band can benefit from the use of cognitive radio (CR) techniques to enable dynamic access to spectrum holes that are free from interference. In this paper, we propose an optimal Green AP Selection (GAPS) scheme, in which AP selection is optimized to maximize the system throughput while minimizing the energy consumption, for multi-rate WLANs enhanced by CRs. Different from most existing AP selection schemes, GAPS takes into account of the state transition tendency of APs and the influence of Automatic Rate Fallback mechanism in the Distributed Coordination Function. The AP selection problem is formulated as a restless bandit problem and solved by the primal-dual index heuristic algorithm based on first order relaxation to yield the GAPS scheme with the "indexability" property and hence a low complexity. GAPS is further divided into offline computation, which accounts for the bulk of the computations, and online selection, with a low complexity to facilitate implementation. Extensive simulation results illustrate the significant performance improvements of GAPS compared with existing AP selection schemes in different scenarios.

In this paper, we study the problem of enhancing the fault tolerance of IEEE 802.11 wireless local area networks in the design stage. Our goal is to place minimal number of APs (access points), such that the system can tolerate AP failures while guaranteeing QoS requirement. Given a set of clients (end-users) in a region, each client has a traffic demand for Internet access. Our concern is to find out minimal number of APs and their locations, so that both fault tolerance and QoS constraints can be satisfied. That is, when there is no AP failure, all clients' traffic demands should be met. When one AP fails, the clients it serves shall switch to other APs and a certain percentage of traffic demands of these clients affected shall still be met. We proposed a heuristic algorithm to solve this problem. Firstly we place minimal number of APs to ensure that connection requirements and per-client degrading traffic demand can be met. Secondly, we continue to add APs to meet per-client normal traffic demand. Finally, we place more APs to tolerate failure of the APs placed in the first step. Simulation are conducted to show the performance of our proposed method.

As a result of the drastic increase in the number of mobile device users, there is considerable public debate about possible health hazards especially due to base stations and Wi-Fi access points. For this reason, in this study the effects of the number of users in a base station and wireless fidelity (Wi-Fi) access point on electric field strength (E) levels were investigated using real-time measurements. Two-stage E measurements were performed on Ondokuz Mayıs University's (OMU) Kurupelit Campus with a PMM-8053 and SRM-3006 electromagnetic field (EMF) meter. In the first stage, 24-h measurements were performed with PMM-8053 at the location where the maximum E was measured and from which the busiest times of the day were then determined. The relationship among band selective E values was assessed using the number of users per minute provided by three cellular system operators for the location. Upper and lower bounds of E according to the number of users were calculated, and then an empirical model that helps calculate the E of medium with 86% accuracy was proposed. In the second stage, the effect of the number of users in a Wi-Fi access point on E level was investigated. For this purpose, the measurement environment was set as including one Wi-Fi access point with needed measurement devices. The number of users was increased as per user per minute. The number of users was validated with the data obtained from OMU IT Department. Using the measurement result, a model with a 96% accuracy between the E value in the environment and the number of users accessing the Wi-Fi system is proposed. With the use of these models, E level in the medium can be determined without using any EMF meters, thus precautions can be taken to stay within regulatory limits.

While the wireless local area network (WLAN) has been the most common technology for static indoor wireless services, its applications has limited performance in seamless mobile services because of its inherent static service transaction mechanisms. In this paper, we propose a mobility provisioning handoff method called dual cross-linking method to support seamless services in WLAN. A mobile node (MN) has two wireless interfaces and access points (APs) are controlled by a mobility management (MM) agent. In the area where the service areas of two adjacent APs are overlapped, one wireless interface is used to maintain the wireless services while the other interface searches for a next available AP. After finding a new AP, MN forms dual communication path from the MM to the MN so that the MN is ready to move to a newly found AP service area without service loss. Once the MN is moved to a new AP area, the first interface is disconnected leaving only one interface connection. It was proved that the proposed method can effectively reduce the handoff delay and packet loss through the analysis.

In recent years, there has been a growing demand in 3G data services, leading to deteriorating 3G service quality. Noting that Wireless Local Area Networks (WLANs) as well as 3G cellular networks are widely available today, WLANs could be effectively utilized to relieve the overload in the 3G networks. On the other hand, use of IEEE 802.11 WLAN Access Points (APs) has proliferated tremendously, resulting in a communication device inside a mobile vehicle to access the Internet. However, using Internet through APs in moving vehicles is challenging since WLAN APs have a short range and are typically not deployed to cover all roads. Several studies have investigated the performance of using intermittently available WLAN connectivity from moving vehicles for data transfers and predictive offloading in WLAN/3G networks. However, these works have not addressed mobility pattern from the viewpoint that drivers' mobility is generally known to have a daily routine. Therefore, in this paper, we consider the user's historical mobility to decide to offload data to WLAN instead of switching to 3G network. The user's application usage pattern is also considered into predicting available WLANs. To evaluate the performance of our offloading algorithm, we analyze the prediction error and conduct simulations. The simulation results show that the proposed algorithm achieves shorter transmission time than the existing schemes that do not consider user's mobility pattern by delivering more data to the WLANs.

Wireless local area network (WLAN) has changed the paradigm of communication and become ubiquitous. As the number of devices connected to wireless is increasing, it is therefore, essential to find vulnerabilities in the security of wireless networks. In this research WLAN security vulnerabilities are exposed in real time. WLAN security techniques (MAC filtering, Hidden SSID and WPA2) available to residential users were practically exploited. Tenda WiFi wireless access point was set up with MAC filtering, hidden SSID and WPA2 security mechanisms in different combinations in such a way as to add an additional layer of security to previous configuration. Kali Linux version 2017.1 was used as a platform to exploit WLAN networks in real time. In this research, the sensitive information broadcasted by WLAN was utilized to carry out attacks on wireless networks. A practical demonstration of exposing vulnerabilities in MAC filtering, Hidden SSID with MAC filtering and WPA2-PSK with hidden SSID and MAC filtering security mechanisms of AP was carried out in real time. It was observed that the existing security mechanisms were vulnerable. Researchers have exploited many security mechanisms of WLAN focusing upon a single parameter of WLAN security at a time. However, in this work, the three available security mechanisms were cascaded to produce a three layer security mechanism i.e. WPA2 with hidden SSID and MAC filtering. This cascaded model was exploited in real time.