WI-FI RSS FINGERPRINTING FOR INDOOR LOCALIZATION USING AUGMENTED REALITY

With growing technology, Location Based Services (LBSs) are becoming a vital part of life. The rapid development of mobile internet has offered an opportunity for Wi-Fi indoor positioning to come under the spotlight due to its low cost. Here, indoor positioning is performed using Wi-Fi. The earlier solutions like GPS does not provide efficient positioning in indoor environment due to weak signal reception which makes Wi-Fi more reliable. However, nowadays the accuracy of the traditional indoor positioning algorithms like trilateration cannot meet the practical requirement. This paper proposes the performance analysis of indoor positioning algorithms using Wi-Fi technology based on Received Signal Strength (RSS) from the access points in the network. The positioning algorithms are based on location fingerprinting consisting of two stages: The offline database creation and the online positioning. The RSS values obtained by the mobile device at reference points are sent to the server where all the location fingerprints of all reference points are stored in a database. Coordinates of user position are calculated using positioning algorithms and the position is displayed in terms of 2Dcoordinates of the room and indoor map. Basic Fingerprint algorithm, RSS Fingerprint with minimum Euclidean Distance algorithm and RSS Fingerprint with Euclidean Distance and k-nearest neighbors' algorithm were implemented. Moreover comparison of their performance was carried out in terms of accuracy of position. From the result, it is found that an average accuracy of 0.4962 meters was achieved by RSS Fingerprint with minimum Euclidean distance algorithm.

In this paper, we propose a surface correlation based fingerprinting method in sparse Wi-Fi environment. The proposed method can estimate location even with very few Wi-Fi APs by using accumulated spatial RSS pattern. We verify performance of the proposed method through several tests in a building with complex paths. Many studies have developed localization technologies that use measurements such as RSS (Received Signal Strength) or RTT (Round Trip Time) for Wi-Fi signal. All RF have signal noise and distortion problems as well as multipath problem in indoor environments. As the distance from the RF signal source increases, the discrimination of the RSS decreases due to RF signal noise and distortion. Therefore, ambiguity of RSS increases as the distance increases, the performance deteriorates. The conventional RF based localization method have tried to maintain dense RF environment to guarantee stable and accurate performance. However, in order to maintain the dense RF environment, it is becoming a barrier to commercialization of localization technology due to high cost of constructing RF infrastructure and maintenance difficulty. In this paper, we propose a Surface Correlation (SC) based fingerprinting technique to maintain high positioning performance even with few Wi-Fi APs. The surface is the accumulated RSS pattern data during the movement of a pedestrian, which means the spatial RSS pattern. Conventional fingerprinting methods using kNN (k-Nearest Neighbors) and WkNN (Weighted kNN) are very vulnerable to signal noise and distortion because they utilize instantaneous RSS data. The performance of Particle Filter (PF) based localization technology is also degraded in areas where Wi-Fi AP is sparsely distributed. However, the proposed method is very robust against signal noise and distortion because it compares the spatial RSS pattern with the reference RSS pattern on the fingerprinting database. This increases localization accuracy and availability for Wi-Fi coverage. For localization, the proposed method conduct correlation process for the spatial RSS pattern of a pedestrian with reference RSS pattern of database. So, the reference RSS pattern should be extracted from a reference trajectory that matches a pedestrian`s walking path. The proposed method utilize a database of ‘link-node’ structure to dynamically generate a reference trajectory in indoor environment with complicated path. It generate candidate reference trajectories using only MAC address and turn event of Pedestrian Dead-Reckoning (PDR). The proposed method fix a reference trajectory between these candidate trajectories through correlation process of measured RSS pattern with each reference RSS pattern. A reference point on the fixed reference having most similar RSS pattern to a pedestrian`s is considered as a current location. In order to improve performance at a fork where RSS ambiguity increases, the proposed method estimates preferentially for a reference trajectory matching with PDR turn event. The turn event can be wrong due to various motion of a pedestrian. The proposed method selects a correct reference trajectory by continuously performing correlation process on candidate reference trajectories. In order to verify the performance of the proposed surface correlation based fingerprinting method, we conducted several tests in a three-story building. Before the tests, we conducted a survey of Wi-Fi environment to construct fingerprinting database in the building. As a result of the survey, 170 APs are distributed in the building. We reduced the number of APs by 20% from 170 to 17, and analyzed performance of the proposed and conventional localization methods. The test results show that the performance of the conventional localization methods degrade as the number of applied APs decreases. The proposed fingerprinting method shows a 3 meter localization error even with very few Wi-Fi APs, and unlike the conventional fingerprinting method, the localization error is bounded to be within 5m due to the use of spatial RSS pattern. In this paper, we presented the fingerprinting method using the surface correlation in sparse Wi-Fi environment. The proposed fingerprinting method accumulates Wi-Fi RSS during movement of a pedestrian. The proposed method compares the spatial RSS pattern, which is accumulated RSS data, with reference RSS patterns of fingerprinting database. By comparing the RSS patterns, the proposed method greatly improves accuracy as well as stability. In addition, it can be effectively applied in a sparse Wi-Fi environment by improving the availability of ambiguous areas of Wi-Fi coverage. Through these results, we expect to be able to provide accurate and reliable location information even in indoor weak RF environment.

In location fingerprinting based indoor positioning system, received signal strength (RSS) indications from a set of Wi-Fi access points are used as a unique fingerprint to identify a specific location. However these RSS fingerprints may become outdated when there are unanticipated environmental changes. Re-measuring RSS fingerprints for all locations to maintain an up-to-date RSS database incurs high operational cost, which is impractical in dynamically changed environment. In this paper, we propose a method to estimate the RSS fingerprint of a specific location from a set of neighboring re-measured RSS fingerprints, called “feedbacks”. The proposed method searches for new feedbacks and some necessary old RSS fingerprints in the cut-off area and then applies plane-interpolation to calculate the new RSS fingerprint for a specific location. Based on simulation results, about 5% of re-measured RSS feedbacks are required to satisfy 80% of positioning correctness in the simulated 30×30 m <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">2</sup> area.

Received signal strength (RSS) fingerprint-based indoor localization has received increasing popularity over the past decades. However, it suffers from the high calibration effort for fingerprint collection. In this paper, a Centralized indooR localizatioN method using Pseudo-label (CRNP) is proposed, which employs a small set of labeled data (RSS fingerprint) along with large volumes of unlabeled data (RSS values without coordinates) to reduce the workload of labeled data collection and improve the indoor localization performance. However, the rich location data is large in quantity and privacy sensitive, which may lead to high network cost (i.e., data transmission cost, data storage cost) and potential privacy leakage for data transmission to the central server. Therefore, a decentralized indoor localization method incorporating CRNP and federated learning is devised, which keeps the location data on local users' devices and improves the shared CRNP model by aggregating users' updates of the model. The experiment results demonstrate that (i) the proposed CRNP enables to improve the indoor localization accuracy by using unlabeled crowdsourced data; (ii) the designed decentralized scheme is robust to different data distribution and is capable to reduce the network cost and prevent users' privacy leakage.

With the WiFi becoming more and more popular over the last few years, the study on the technology of indoor positioning based on WiFi is given more and more attention. Being specific to the problem that not all the clustered reference points(RPs) of the traditional clustering algorithm have geometric proximity in indoor positioning, this paper puts forward the affinity propagation presentation(AP) which bases on the combination of geometry and received signal strength (RSS). Being different from the traditional clustering algorithm, this kind of algorithm can endow the RPs with geometrical and endow the RSS with corresponding weight according to the positioning conditions, it can use the features of the geometry and RSS to restrain the sort of RPs, and that can make the sort of RPs more reasonable. After that it will use k-Nearest Neighbor Algorithm(KNN) to have accurate positioning, which not only can reduce the calculation, but also improve the localization accuracy. Simulation shows that, this kind of algorithm possesses the advantage of fast location and higher localization accuracy.

The Internet of Things (IoT) is an emerging paradigm to integrate the physical world into cyber systems by connecting various devices, which sense and control the surrounding objects. For the upcoming IoT era, narrow-band signals will play an important role in the exchange of sensor data and control signals in IoT networks. Indoor positioning is critical for many IoT applications, such as asset tracking, smart buildings, smart e-health, and smart cities, but it is very challenging to achieve accurate indoor positioning with narrowband signals because of multipath propagation. In this paper, we design a positioning system using narrowband signals, particularly ZigBee signals, based on an enhanced fingerprinting algorithm by fusing received signal strength (RSS) and time information. We first investigate the feasibility of time-based fingerprinting by handling the challenges as synchronization compensation among anchor nodes and design of sub-sample timestamps with a resolution of nanoseconds. Second, we design a feature-based fusion approach to fuse and standardize time and RSS fingerprints. Third, we adopt a random forest regression model to design an enhanced pattern matching algorithm for fingerprinting. We implement the proposed algorithms with software-defined radio techniques. In the given experiment results, we find that the positioning system achieves a mean positioning accuracy of 1.61 m, which represents a 36.1% improvement over traditional RSS-based fingerprinting.

The indoor pedestrian positioning methods are affected by substantial bias and errors because of the use of cheap microelectromechanical systems (MEMS) devices (e.g., gyroscope and accelerometer) and the users’ movements. Moreover, because radio-frequency (RF) signal values are changed drastically due to multipath fading and obstruction, the performance of RF-based localization systems may deteriorate in practice. To deal with this problem, various indoor localization methods that integrate the positional information gained from received signal strength (RSS) fingerprinting scheme and the motion of the user inferred by dead reckoning (DR) approach via Bayes filters have been suggested to accomplish more accurate localization results indoors. Among the Bayes filters, while the particle filter (PF) can offer the most accurate positioning performance, it may require substantial computation time due to use of many samples (particles) for high positioning accuracy. This paper introduces a pedestrian localization scheme performed on a mobile phone that leverages the RSS fingerprint-based method, dead reckoning (DR), and improved PF called a double-stacked particle filter (DSPF) in indoor environments. As a key element of our system, the DSPF algorithm is employed to correct the position of the user by fusing noisy location data gained by the RSS fingerprinting and DR schemes. By estimating the position of the user through the proposal distribution and target distribution obtained from multiple measurements, the DSPF method can offer better localization results compared to the Kalman filtering-based methods, and it can achieve competitive localization accuracy compared with PF while offering higher computational efficiency than PF. Experimental results demonstrate that the DSPF algorithm can achieve accurate and reliable localization with higher efficiency in computational cost compared with PF in indoor environments.

Understanding the indoor whereabouts of individuals and objects is important, especially for those who fall within the 71% of visually impaired individuals with a school education, students in 450 special education units and many other areas and aspects in Sri Lanka. Researchers have declared that, there isn’t any particularly good localization system, and the performance should be evaluated considering the approach and application. The most well-known indoor positioning (IP) technologies that have been historically deployed are Bluetooth, Wi-Fi, RFID (radio frequency identification), IR (Infrared), and UV (ultraviolet) whereas received signal strength (RSSI), fingerprinting, and triangulation methods have been used as common IP techniques. The combination of both IP technologies and techniques creates an IP system, and the integration of machine learning and IoT with the structured system essentially delivers an accurate and more advanced system. This paper contains a detailed, analytical review of a developed indoor positioning system derived from the existing indoor localization techniques, localization technologies, localization systems, algorithms, and performance matrixes. This also provides a comprehensive comparison between numerous existing systems to justify the proposed solution. This project has been developed to achieve better accuracy through low-cost deployment as an effective system to fill the gap in the scarcity of positioning systems in the world. This paper presents a descriptive introduction and problem definition, a critical discussion of results, machine learning models, benefits of the project, and future works. As later justified, ESP32 microcontroller and BLE beacons are utilized with RSSI fingerprinting method to develop this IP system and, as a part of the project, two data visualization methods have been introduced here using NodeRED dashboard and LC display. Overall, this project was developed with an effective combination of RSSI fingerprinting, IoT protocols, machine learning, and data interpretation methods. KEYWORDS: Indoor positioning, RSSI, Fingerprinting, Machine Learning, MQTT, ESP32, BLE beacons, NodeRED

The fingerprint location method based on the WiFi received signal strength (RSS), is one of the indoor positioning method owning the highest value of application currently. It uses distribution characteristic of WiFi RSS in the space to estimate user's location. But due to the unstable RSS measurements of WiFi signal in a fixed location, in online phase, the uncertain fluctuation of RSS measurements will cause matching error of reference point (RP), and lead to the positioning error. To deal with this problem, a matching positioning method combining spatial multi-points fingerprint is presented in this paper. Firstly, assisted by odometer information, the space uniforming calibration of fingerprint is carried out in radial direction of road. And then, intensity and variation characteristics in space of consecutive multi-points RSS are matched jointly in online process, so as to enhance the positioning accuracy and stability. Through experiments, it is proved that the method in this paper is effective and, under reasonable parameters, positioning performance is good.

Due to an increasing number of public and private access points in indoor and urban environments, Wi-Fi positioning becomes more and more attractive. In last ten years different approaches and solutions have been developed and applied. The accuracy of these systems depends on the suitability of the propagation models used for the actual propagation conditions. In this paper, characteristic and analysis of two popular methods for indoor localization named as K-Nearest Neighbour (K-NN) algorithm based RF Fingerprinting and RF Multilateration methods are experimentally evaluated and compared according to received signal strength (RSS) of a mobile Wi-Fi user for getting a better and improved result. Transmitted signal strengths of four fixed Wi-Fi modems are measured by using a mobile Mac Computer with Wi-Fi receiver in the School of Electrical and Electronics Engineering hallways at Yildiz Technical University, Istanbul. Later, accuracy plots and modelling for better solution in small areas and LoS locations has been demonstrated for both methods. An experimental comparison results has been presented to evaluate the performance in localizing accuracy where RF Fingerprinting method shows better results than RF multilateration method while RF multilateration method offers less error rate and better solution for small areas.

Received signal strength (RSS) based location fingerprinting is a powerful wireless positioning technique. It estimates the target location by consulting a preliminary database and searching for the best matched RSS fingerprints. The construction and maintenance of a sufficient fingerprint database could be laborious and problematic. This paper proposes a new approach that utilizes the Kriging spatial interpolation algorithm to build complete fingerprint databases from sparsely collected measurements. The interpolation performance is analyzed over various extents of sparsity and number of measurements. The constructed fingerprint databases are utilized to locate a static target and the localization performances are analyzed. It is shown that the Kriging algorithm can be used to build RSS fingerprint databases of good accuracy based on sparsely collected measurements.

Many indoor fingerprinting localization methods are based on signal-domain distances with large localization error and low stability. An improved fingerprinting localization method using a clustering algorithm and dynamic compensation was proposed. In the offline stage, the fingerprint database was built and clustered based on offline hybrid distance and an affinity propagation clustering algorithm. Furthermore, clusters were adjusted using transition regions and a given radius, as well as updating the corresponding position and fingerprint of the cluster centroid. In the online stage, the lost received signal strength (RSS) in the reference fingerprint would be dynamically compensated by using a minimum RSS value, rather than a fixed one. Online signal-domain distance was calculated for cluster identification based on RSS readings and compensated reference fingerprint. Then, K reference points with minimum online signal-domain distances were selected, and affinity propagation clustering was reused by position-domain distances to choose the position-concentrated sub-cluster for location estimation. Experimental results show that the proposed method outperforms state-of-the-art fingerprinting methods, with the mean error of 2.328 m, the root mean square error of 1.865 m and the maximum error of 10.722 m in a testbed of 3200 square meters. The improvement rates, in terms of accuracy and stability, are more than 21% and 13%, respectively.

A novel indoor localization method for Wi-Fi devices such as smart phones is presented. With an indoor path loss model, the distance between a mobile device (MD) and an access point (AP) can be estimated form the received signal strength (RSS). Then, least-squared-error (LSE) triangulation yields the position of the MD. Though indoor channel characteristics are highly fluctuating with perturbations, a reference point (RP) can be used to compensate for channel instability. We present two contributions: cross monitoring AP and weighted triangulation. Cross monitoring AP removes the need of deploying RPs since it can play the dual role of a regular AP and a RP. Weighted triangulation yields improvement in the accuracy of LSE estimation of the MD position. Experimental results show weighted triangulation with cross monitoring AP provides indoor localization with an error less than 2 meters.

Indoor localization systems have already wide applications for providing localized information and directions. They can also be very useful in medical applications, as an individual’s indoor movements can be indicative of his/her clinical status. Research for indoor localization systems is ongoing and there are numerous solutions with different hardware or algorithmic approaches, for different use cases. Ease of setup and cost are significant factors when using indoor localization systems for medical applications. This paper proposes an indoor localization system with room-level accuracy, focusing on an easy installation procedure that can be easily followed from non-technical staff, as well as on low cost, so that it can be widely adopted. The proposed system has been mainly designed for behavioural monitoring of adults in an indoor environment. The system operates by tracking a carried device based on the processing of RSS (Received Signal Strength) measurements from Bluetooth Low Energy beacons placed in the area. The proposed system has been evaluated in realistic settings and and achieves an accuracy of 95.31% in room estimation.

Crowdsensing is more and more used nowadays for indoor localization based on Received Signal Strength (RSS) fingerprinting. It is a fast and efficient solution to maintain fingerprinting databases and to keep them up-to-date. There are however several challenges involved in crowdsensing RSS fingerprinting data, and these have been little investigated so far in the current literature. Our goal is to analyse the impact of various error sources in the crowdsensing process for the purpose of indoor localization. We rely our findings on a heavy measurement campaign involving 21 measurement devices and more than 6800 fingerprints. We show that crowdsensed databases are more robust to erroneous RSS reports than to malicious fingerprint position reports. We also evaluate the positioning accuracy achievable with crowdsensed databases in the absence of any available calibration.