Mining activities are conducted to extract valuable minerals from the Earth, which are used to manufacture many objects. However, these operations generate landform alterations, such as deep excavations, artificial embankments, and landscape reshaping. In this study, landform changes were monitored in a mining area in Mazapil, Zacatecas, Mexico, using geomatic techniques. Multitemporal Landsat satellite images and digital elevation models (DEMs) from different years were used to detect and quantify landform alterations and estimate the volumes of removed material. The results show ground depressions greater than −333 m and waste material accumulations greater than +152 m, with an average standard deviation of ±3.6 m. A total excavation volume of 413.524 million m3 and a total fill volume of 431.194 million m3 were quantified, with an estimated standard deviation of ±810 m3. The proposed methodology proved effective for the remote quantification of large-scale relief disturbances in open-pit mining areas. It can also be used for environmental monitoring and hydrological risk assessment in active and inactive mining areas.

The study at the Sanctuary of Eukleia in Aigai (Vergina, Greece) evaluates the planimetric and vertical accuracy of Digital Surface Model (DSM) generated by a Hesai XT32M2X LiDAR system mounted on UAS WingtraOne GEN II. The paper begins by outlining the evolution of UAS-LiDAR, then describing the acquisition of RGB, multispectral (MS) images and LiDAR data. Twenty-two Check Points (CPs) were measured using an RTK-GNSS receiver, which also served to establish the PPK calibration base point. This is followed by processing the images to generate DSMs and orthophotomosaics, as well as processing the LiDAR point cloud to produce both DSM and DTM products. The DSMs and orthophotomosaics were evaluated by comparing field-measured CP coordinates with those extracted from the products, computing mean values and standard deviations. RGB images yielded DSMs and orthophotomosaics with planimetric accuracy of 1.4 cm (with a standard deviation σ = ±1 cm) in X, 0.9 cm (with σ = ±0.9 cm) in Y and a vertical accuracy of 2.4 cm (with σ = ±1.7 cm). The LiDAR-derived DSM achieved similar planimetric accuracy and an overall vertical accuracy of 7.5 cm (with σ = ±6 cm). LiDAR’s ability to penetrate vegetation enabled near-complete mapping of a densely vegetated streambank, highlighting its clear advantage over images. While high-precision RGB-PPK products can surpass LiDAR in vertical accuracy, UAS-LiDAR remains indispensable for under-canopy terrain mapping.

Predicting subsoil properties accurately is important for engineering tasks like construction, land development, and environmental management. However, traditional approaches that use borehole data often face challenges because the data is sparse and unevenly spread, which can cause uncertainty in understanding the subsurface. This study introduces a novel geostatistical framework employing Empirical Bayesian Kriging 3D (EBK3D) within a Geographic Information System (GIS), which was developed to construct three-dimensional lithological models. The framework was applied to 265 boreholes from the Queen Mary Reservoir in London. ArcGIS Pro was used to interpolate lithology layers using EBK3D, resulting in voxel-based models that represent both horizontal and vertical lithological variations. Model validation was performed with an independent dataset comprising 30% of the boreholes. The results demonstrated high predictive accuracy for layer elevations (Pearson’s r = 0.99, MAE = 0.31 m). The model achieved 100% accuracy in predicting borehole stratigraphy in homogenous zones and correctly identified 77% of lithological layers in heterogeneous zones. In complex regions, the model accurately predicted the whole borehole in 49% of cases. This framework provides a reliable, repeatable, and cost-effective method for three-dimensional subsurface characterization, enhancing traditional approaches by automating uncertainty quantification and capturing both vertical and horizontal variability.

The objective of this study is to quantify and characterize ground deformations induced by underground coal mining in the Karaganda coal basin, Kazakhstan, in order to improve the understanding of subsidence processes and their long-term evolution. The SBAS-InSAR method was applied to Sentinel-1 (C-band) and TerraSAR-X (X-band) data from 2019–2021 to estimate the magnitude, extent, and temporal behavior of displacements over the Kostenko, Kuzembayev, Aktasskaya, and Saranskaya mines. The results reveal spatially coherent and progressive deformation, with maximum cumulative LOS displacements exceeding –800 mm in TerraSAR-X data within active longwall mining zones. Time-series analysis confirmed acceleration of displacement during active extraction and its subsequent attenuation after mining ceased. Comparative assessment demonstrated a strong agreement between Sentinel-1 and TerraSAR-X results (r = 0.9628), despite differences in resolution and acquisition geometry, highlighting the robustness of the SBAS-InSAR approach. Analysis of displacement over individual longwalls showed that several panels (3, 5, 8, 15, and 18) already exceeded their projected maximum subsidence values, underlining the necessity of continuous monitoring for ensuring safety. In contrast, other longwalls have not yet reached their maximum deformation, indicating potential for further activity. Overall, this study demonstrates the value of multi-sensor InSAR monitoring for reliable assessment of mining-induced subsidence and for supporting geotechnical risk management in post-industrial regions.

We investigate the applicability of visual foundation models, a recent advancement in artificial intelligence, for archaeological remote sensing. In contrast to earlier approaches, we employ a strictly zero-shot methodology, testing the hypothesis that such models can perform archaeological feature detection without any fine-tuning or other adaptation for the remote sensing domain. Across five experiments using satellite imagery, aerial LiDAR, and drone video data, we assess the models’ ability to detect archaeological features. Our results demonstrate that such foundation models can achieve detection performance comparable to that of human experts and established automated methods. A key advantage lies in the substantial reduction of required human effort and the elimination of the need for training data. To support reproducibility and future experimentation, we provide open-source scripts and datasets and suggest a novel workflow for remote sensing projects. If current trends persist, foundation models may offer a scalable and accessible alternative to conventional archaeological prospection.

This study evaluates the impact of incorporating lateral mass density variations into geoid models for Java, Indonesia, aiming to enhance the accuracy of regional geoid determinations. Geoid models have traditionally used a constant density assumption; however, Java’s varied topography and geological complexity suggest that density variability may significantly influence geoid accuracy. Employing the Stokes–Helmert method combined with the remove–compute–restore (RCR) technique, we calculated geoid models using both constant density and laterally variable density from the UNB TopoDens model. The models were validated against GNSS/leveling data, showing that while lateral density variations had limited effects along flat topographic profiles, they introduced notable discrepancies in regions with considerable elevation changes. Specifically, variable density models exhibited discrepancies of up to 30 cm in regions with complex terrain, underscoring the importance of selecting appropriate density models for precise geoid computations in heterogeneous landscapes. Nonetheless, a comprehensive validation using geometric geoid models is required to confirm the accuracy improvements across the entire region.

Documenting and preserving cultural heritage assets is increasingly important, with threats from natural disasters, conflicts, climate change, and neglect, and some sites are both contested and physically difficult to access or document, posing the issue of “challenging heritage”. A range of innovative digital methods have emerged, offering practical, low-cost, efficient techniques for the 3D documentation of threatened heritage, including smart phone-based mobile light detection and ranging (LiDAR) and photogrammetry. Such techniques offer quick, accessible, and cost-effective alternatives to terrestrial laser scanners, albeit with reduced accuracy and detail, offering practical solutions in cases with restricted funding, limited time for access, complex architectural geometries, or the unavailability of high-end equipment on site. This paper presents a real-world case study integrating iPhone LiDAR with aerial photogrammetry for the rapid documentation of Sourp Magar Monastery, a Medieval site located in a forested slopes of the Kyrenia Range, Cyprus. Due to its poor state of preservation and years of abandonment, as well as its remote nature and location, the monastery is considered a “challenging heritage” monument. In the context of a recent international restoration initiative, a preliminary digital survey was undertaken to both document the current condition of Sourp Magar and contribute to a better understanding of its construction history. This paper outlines the workflow integrating the use of smartphone LiDAR and aerial photogrammetry, evaluates its efficacy in challenging heritage sites, and discusses its potential implications for rapid, low-cost documentation. Finally, the present paper aims to show the multifaceted benefit of easy-to-use, low-cost technologies in the preliminary study of sites and monuments.

Agricultural productivity is closely linked to the spatial variability of soil physical properties. However, high variability makes it difficult to implement effective management strategies, and the constant expansion of eucalyptus plantations in certain areas alters the soil’s physical properties. This study conducted a geostatistical analysis of the physical properties of a soil in Sogamoso, Boyacá (Colombia), which contains areas with different management practices and vegetation cover, among which the presence of Eucalyptus globulus stands out. Ninety-seven points were sampled in an area of 29.1 ha, with multiple land uses. The data were analyzed using descriptive statistics and geostatistical analysis, which determined the semivariogram parameters, the degree of spatial dependence, and the best-fitting interpolation model for mapping. A correlation analysis between variables was also performed. Analysis of variance showed no significant differences among vegetation covers (dense forest, grass-crop mosaic, weedy grassland, and crop mosaic), indicating structural homogeneity. The hydraulic conductivity (Ksat) had the highest coefficient of variation (CV), at 141.9%, while particle density had the lowest CV, at 9.25%. Ksat (exponential model, range = 207 m) and porosity (spherical model, range = 98 m) showed a strong spatial dependence. Ksat was lower in areas with eucalyptus (0.01 to 0.2 m day−1), attributed to hydrophobicity induced by organic compounds emitted by these plantations. Soil moisture contents showed lower values in areas with eucalyptus, corroborating their high water consumption. Soil aggregates were lower when eucalyptus plantations were on slopes greater than 15%. Porosity showed an inverse correlation with apparent density (r2 = −0.86).

This article presents a comprehensive evaluation of image segmentation methods for monitoring morphological changes in refugee camps, comparing five distinct approaches: ESRI Landviewer clustering, K-means clustering, U-Net segmentation, Meta’s Segment Anything Model (SAM) and ArcGIS segmentation. Using high-resolution satellite imagery from Al-Azraq refugee camp in Jordan (2014–2023) as a case study, this research systematically assesses each method’s performance in detecting and quantifying settlement pattern changes. The evaluation framework incorporates multiple validation metrics, including overall accuracy, the Kappa coefficient, F1-score and computational efficiency. The results demonstrate that ArcGIS’s ISO clustering and classification approach achieves superior performance, with 99% overall accuracy and a Kappa coefficient of 0.95, significantly outperforming the other tested methods. While Meta SAM shows promise in object detection, its performance degrades with aerial imagery, achieving only 75% accuracy in settlement pattern recognition. The study establishes specific parameter optimization guidelines for humanitarian contexts, with spectral detail values of 3.0–7.0 and spatial detail values of 14.0–18.0, yielding optimal results for refugee settlement analysis. These findings provide crucial methodological guidance for monitoring refugee settlement evolution and transition, contributing to more effective humanitarian response planning and settlement management through integrating remote sensing and machine learning technologies.

Positional accuracy in cadastral data is fundamental for secure land tenure and efficient land administration. However, many land administration systems (LASs) experience difficulties to meet accuracy standards, particularly when data come from various sources or historical maps, leading to disruptions in land transactions. This study investigates the use of unsupervised clustering algorithms to identify and characterize systematic spatial error patterns in cadastral maps. We compare Fuzzy c-means (FCM), Density-Based Spatial Clustering of Applications with Noise (DBSCAN), and Gaussian Mixture Models (GMMs) in clustering error vectors using two different case studies from Greece, each with different error origins. The analysis revealed distinctly different error structures: a systematic rotational pattern surrounding a central random-error zone in the first, versus localized gross errors alongside regions of different discrepancies in the second. Algorithm performance was context-dependent: GMMs excelled, providing the most interpretable partitioning of multiple error levels, including gross errors; DBSCAN succeeded at isolating the dominant systematic error from noise. However, FCM struggled to capture the complex spatial nature of errors in both cases. Through the automated identification of problematic regions with different error characteristics, the proposed approach provides actionable insights for targeted, cost-effective cadastral renewal. This aligns with fit-for-purpose land administration principles, supporting progressive improvements towards more reliable cadastral data and offering a novel methodology applicable to other LASs facing similar challenges.