Background: Nanocomposite resins have been widely used in modern denture manufacturing. However, their long-term color stability is a concern for both dental professionals and patients. Purpose: to evaluate the effect of different beverages on the color stability of 3D-printed denture base resins modified with zirconium dioxide nanoparticles (ZrO2NPs). Methods: A total of 440 specimens were fabricated and distributed into 11 groups (n = 40/group). The control group of heat polymerized (PMMA) and five groups of two different 3D-printed resins (NextDent and ASIGA) as experimental groups with various concentrations of ZrO2NPs added to the 3D-printed resins (0.5 wt%, 1 wt%, 3 wt%, 5 wt%) in addition to one unmodified group per resin. Specimens per group are sorted into four subgroups (n = 10) according to tested beverages, as follows: coffee, tea, cola, and mineral water. Before immersion, all the specimens were exposed to 5000 thermal cycles. Color changes (ΔE00) were assessed prior (T0) and following immersion for 6 days (T1) and 12 days (T2) using a spectrophotometer. Color difference values were calculated by using CIEDE2000 color difference. Data was analyzed by ANOVA and post hoc Tukey test with a significant level of less than 0.05. Results: Tea produced the highest color change for both NextDent and ASIGA materials, whereas water caused the least color change on PMMA at T2. Increasing the immersion time resulted in more color changes, with tea and coffee showing significant differences. PMMA had considerably less color change than 3D-printed resins. The color change of 3D-printed increased after adding ZrO2NPs. Conclusions: Beverage type and immersion time have an impact on the color stability of unmodified and ZrO2NP-modified denture base resins with significant change after immersion in tea and coffee.

Dental rehabilitation with implants is a clinical reality in clinical practice. The Interproximal Contact Loss (ICL) between implant-supported prostheses adjacent to natural teeth is a relatively common occurrence. This systematic review and meta-analysis aims to evaluate the possible clinical effects of the periodontium regarding the ICL between teeth and implanted-supported prostheses. We also identified the main ICL assessment tools described in the literature. This study was registered on the PROSPERO (CRD42023446235), was based on the PICO strategy, and followed the PRISMA guidelines. An electronic search was carried out in the PubMed, B-on, Google Scholar, and Web of Science databases without setting a time limit for publications. Only systematic reviews and comparative clinical trials were included and analyzed. Nineteen publications were eligible for meta-analysis, with thirteen retrospective and six prospective clinical trials. A total of 2047 patients and 7319 prostheses in function were evaluated, and ICL was found in 51% with a confidence interval of 0.40 to 0.61. As ICL assessment tools, dental floss was used in 65%, matrices were used in 30%, and X-ray images were used in 5% of cases. The clinical follow-up ranged from 1 to 21 years, with 50% between 1 and 3 years, 25% between 3 and 10 years, and 25% between 10 and 21 years. ICL was found to occur more frequently in the mandible. No statistically significant difference existed between the anterior (55%) and posterior (47%) oral regions. On the mesial surface, ICL ranged from 13% to 81.4%, possibly due to the different follow-up periods and the diversity of methods used in the assessment. No differences were found for ICL between single or multiple implanted-supported prostheses. Food impaction was the most common effect of ICL and was more prevalent on the implant-supported prosthesis’s mesial surface in the mandible’s posterior region. There was evidence of peri-implant mucositis but without progression to peri-implantitis, and the form of retention or the number of elements was not relevant.

Considering the rapid evolution of lithium silicate-based glass ceramics (LSCs) in dentistry, this review paper aims to present an updated overview of the recently introduced commercial novel LSCs. The clinical and in vitro English-language literature relating to the microstructure, manufacturing, strengthening, properties, surface treatments and clinical performance of LSC materials was obtained through an electronic search. Findings from relevant articles were extracted and summarised for this manuscript. There is considerable evidence supporting the mechanical and aesthetic competency of LSC variants, namely zirconia-reinforced lithium silicates and lithium–aluminium disilicates. Nonetheless, the literature assessing the biocompatibility and cytotoxicity of novel LSCs is scarce. An exploration of the chemical, mechanical and chemo-mechanical intaglio surface treatments—alternative to hydrofluoric acid etching—revealed promising adhesion performance for acid neutralisation and plasma treatment. The subtractive manufacturing methods of partially crystallised and fully crystallised LSC blocks and the additive manufacturing modalities pertaining to the fabrication of LSC dental restorations are addressed, wherein that challenges that could be encountered upon implementing novel additive manufacturing approaches using LSC print materials are highlighted. Furthermore, the short-term clinical performance of zirconia-reinforced lithium silicates and lithium–aluminium disilicates is demonstrated to be comparable to that of lithium disilicate ceramics and reveals promising potential for their long-term clinical performance.

Implant-supported-screw-retained prostheses are highly popular. Some of the most frequent complications are connected with the mechanical properties of the fixing elements. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, few studies detail how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to direct implant-supported restoration. It was carried out using the finite element method (FEM) and was experimentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffered higher stress than the one screwed directly into the implant. After applying a cyclic fatigue load, it was experimentally proven that, in the transepithelial-supported restorations, the fuse changed from being the screw that went into the implant to being the upper one. In conclusion, we can state that the use of an intermediate abutment in dental restoration not only provides better protection for the rest of the dental restoration but also allows for easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

This review article aims to provide an updated and comprehensive overview of the latest trends in adult upper limb prostheses, specifically targeting various amputation levels such as transradial, transmetacarpal, transcarpal, and transhumeral. A systematic search was conducted across multiple databases, including IEEE Xplore, MDPI, Scopus, Frontiers, and Espacenet, covering from 2018 to 2023. After applying exclusion criteria, 49 scientific articles (33 patents and 16 commercial prostheses) were meticulously selected for review. The article offers an in-depth analysis of several critical aspects of upper limb prostheses. It discusses the evolution and current state of input control mechanisms, the number of degrees of freedom, and the variety of grips available in prostheses, all tailored according to the level of amputation. Additionally, the review delves into the selection of materials used in developing these prostheses and examines the progression of technology readiness levels. A significant focus is also placed on the evolution of prosthesis weight over the years for different amputation levels. Moreover, the review identifies and explores critical technological challenges and prospects in upper limb prostheses. Finally, the article culminates with a conclusion that encapsulates the key findings and insights on the advancements and ongoing developments in this field.

The literature shows evidence of the mechanical investigation of numerous polymeric dental biomaterials using a static approach. A more representative mechanical analysis of such materials must take into account the dynamic masticatory load of the oral cavity. The aim of this work is to study the dynamic mechanical proprieties and provide an in vitro characterization of 11 3D-printed new dental biomaterials to understand their clinical applications under physiological conditions. The analysis included Dynamical Mechanical Analysis (DMA) and an MTT cytotoxicity assay. The mechanical results at low frequencies (1–11 Hz) show high uncertainty, less fragility, and less strength. The biological results show a significant reduction in cell viability (p < 0.01) at both the 3 and 24 h timepoints, with a degree of recovery observed at 24 h. To assess the clinical potential of dental biomaterials, it is necessary to determine whether there are good dynamic mechanical properties and reduced adverse biological effects on oral cells. This may allow for the facile fabrication via 3D printing of prosthetic devices that can support masticatory loads over long periods of time. Further investigations of the presented polymeric materials are needed, exploring biological assessments for longer than 24 h.

Background: Bleeding complications are strong predictors of mortality and major morbidity in elderly patients undergoing surgical aortic valve replacement (SAVR) or transcatheter aortic valve implantation (TAVI). Despite the high prevalence of frailty in this population, little is known about its effects on bleeding risk. Methods: We conducted a retrospective observational study of 502 patients undergoing isolated SAVR or TAVI between January 2015 and February 2022. The occurrence of blood products transfusions and MACEs were the primary endpoints. In-hospital mortality was the secondary endpoint. Results: The Elderly group (age < 80 years old) included 475 subjects, whereas the Very Elderly group (age ≥ 80 years old) included 127 patients. The need for blood product transfusion was similar among the two groups, regardless of the type of procedure. MACEs occurred similarly between groups [SAVR: Elderly group: 7.9% vs. Very Elderly group: 8.6%, p = 0.864; TAVI: Elderly group: 5.5% vs. Very Elderly group: 8.7%, p = 0.378]. The was no difference in in-hospital mortality rate in patients submitted to TAVI, whereas very elderly patients had higher mortality rate compared to the elderly patients submitted to SAVR [SAVR: Elderly group: 0% vs. Very Elderly group: 2.8%, p = 0.024; TAVI: Elderly group: 4,8% vs. Very Elderly group: 8%, p = 0.389]. Conclusions: Age alone should not be considered as a predictive factor for post-operative adverse events or in-hospital mortality in elderly patients with severe symptomatic AS.

Obtaining a proper position for total hip arthroplasty components is a crucial aspect of implant performance and consequently of patient outcomes. Restoring the original hip center and maintaining the limb length are key factors in reaching the optimal implant positioning. The aim of this study was to assess the accuracy and safety of a computed dynamic analysis system that, through patient-specific guides, tries to improve implant positioning and functional orientation according to patients’ spinopelvic mobility and anatomy. A total of 100 consecutive patients were prospectively enrolled. All patients received an Optimized Positioning System dynamic hip preoperative planning schedule. A CT scan protocol follow-up analysis was performed 6 months after surgery. The mean deviations from the planned acetabular inclination and anteversion were 4.3° and 3.8°, respectively. In total, 98% of cases were within ± 10° of the Lewinnek safe zone, both for inclination and anteversion. The height of osteotomy deviated, on average, 1.6 mm. In total, 100% of cases were included within 4 mm of osteotomy. Patient-specific and laser-guided instrumentation was found to be safe and accurately reproduced dynamic planning in terms of the component orientation, osteotomy level, leg length and offset.

Hip arthroplasty failures (either septic or aseptic) often require multiple revisions, thus leading to severe bone defects. The most common reconstruction methods do not allow the management of severe defects. For this reason, in recent years, techniques borrowed from surgical oncology have been applied in the field of revision surgery to deal with both acetabular and femoral bone losses. In this article, two cases of severe bone deficiency following multiple hip arthroplasty revisions that were treated with a custom-made hip prosthesis combined with a proximal femur megaprosthesis are presented. Both implants were silver coated. A review of the literature was conducted to analyze similar cases treated with either a custom-made prosthesis or a proximal femur megaprosthesis. At the 2-year follow-up, all prostheses were in site without clinical or radiographic signs of implant loosening. No postoperative complications occurred. At the last follow-up, both patients resumed their daily life activities with an MSTS score of 23 and 21, respectively. The combined approach of a proximal femur megaprosthesis with a custom-made partial pelvic replacement is a solution that allows severe bone deficiency cases to be tackled with good functional results. Additionally, silver coating may help prevent recurrence of infection.

The main aim of this case series was to report the clinical and radiographic outcomes of 22 one-piece zirconia dental implants positioned in 19 patients to restore single edentulisms and followed up for at least 2 years. The mean observation period was 58.18 months. At the last follow-up visit, no issues, such as foreign body sensation, discomfort or pain, were reported by the patients. No implant showed signs of infection with suppuration or implant mobility. Marginal bone levels (MBL) were assessed through standardized dental radiographs and a dedicated software. The mean distance between the implant head and the first detectable bone to implant contact was calculated at the mesial and distal aspect of each implant. The mean MBL at baseline was 1.82 ± 0.63 mm while the mean MBL at the last follow-up visit was 2.57 ± 0.72 mm. The results obtained in the present case series over a mean follow-up period of 58.18 months (range 27–96) showed that one-piece zirconia dental implants could be an alternative option to support single crowns in patients requiring metal-free restorations. Nevertheless, further better-controlled research featuring an adequate study design and longer follow-up is needed in order to clarify advantages and limitations which are related to this treatment modality.