Periodic structures that may exist within the neutron imaging detector can introduce periodic noise into the imaging results, directly degrading image quality and further affecting the performance of deconvolution. This periodic noise appears as four-pointed star-shaped peaks in the amplitude spectrum of the frequency domain. However, the distribution of honeycomb-like noise structures in neutron imaging results makes it difficult to detect using conventional thresholding methods. We propose a method that applies a dilation operation before threshold detection to enhance the contrast between peaks and the surrounding areas. Then, a notch filter is used to smooth the peaks containing noise information, thereby removing the periodic noise structure. This approach effectively eliminates honeycomb structures of approximately 40 micrometers and improves the image quality after deconvolution processing.

In this paper, several optimized design results of the HTGR-based 10 MWth Reaktor Daya Eksperimental (RDE) (Experimental Power Reactor), so far conducted, are reviewed and compared from the neutronics, reactor types, refueling schemes, and fuel cycle points of view. The review covers the multipass and once-through-then-out (OTTO) pebble-bed cores, as well as block/prismatic type cores with several fuel shuffling options. As for the fuel cycle, uranium and thorium fuels are considered. The fuel burnup performance and power distribution are evaluated and compared among other important design parameters. Reactor physics codes, nuclear data libraries, and calculation models and procedures used for the design and analysis are reviewed, and challenges for future improvements are discussed.

This paper presents a thermal management solution for a Ka-band gyrotron traveling wave tube (gyro-TWT) with non-superconducting magnets. At present, the miniaturization and non-superconductivity of gyro-TWT have become a trend, but miniaturization leads to a significant increase in power density and a severe limitation in heat sink volume, which critically limits power capacity. To address this challenge, a joint microwave–thermal management evaluation model is used to investigate the heat transfer process and identify the crucial factors constraining the power capacity. A cylindrical heat sink with narrow rectangular grooves is introduced. Based on this, the cooling efficiency has been enhanced through structural optimization. The beam–wave interaction, electrothermal conversion, and heat conduction processes of the interaction circuit are analyzed. The compact heat sink achieves a 1.2-fold increase in coolant utilization and reduces the overall volume by 27.4%. Meanwhile, this heat sink improves the cooling performance and power capability of the gyro-TWT effectively. At 29 GHz, the gyro-TWT achieves a pulse power of 150 kW. Simulation results show that the maximum temperature is 348 °C at a 45% duty cycle, reduced by 159 °C. The power capacity of the Ka-band gyro-TWT increases by 40.6%.

Polarized neutron reflectometry (PNR) analyzes surface and interfacial structures of materials. For the SHARAKU reflectometer at the Materials and Life Science Experimental Facility in the Japan Proton Accelerator Research Complex, precise measurements under weak magnetic fields, which are critical for modern spintronics, have long been challenging. To address this issue, we developed a precise weak-field sample environment equipped with a newly designed coil system. The magnetic field at the sample position can be applied within the surface/interface plane, either in the scattering plane (horizontal configuration) or perpendicular to it (vertical configuration). The horizontal configuration achieved high polarization efficiency across a stable field range, whereas the vertical configuration enabled the experiments to cross zero into negative fields. We demonstrated the instrument’s capability by resolving the remanent magnetic structure of an Fe film. Its applicability to soft matter was proven through analysis of a cellulose thin film with roughness using magnetic contrast variation PNR. In this case, precise weak-field control is essential to tune the magnetic contrast from the reference layer beneath the soft film. These results establish the system as a versatile platform for future PNR and polarized off-specular scattering experiments across a wide range of materials.

Cracks due to stress corrosion cracking in stainless steels are becoming a problem not only in boiling water reactors but also in pressurized water reactor nuclear plants. Stress improvement measures have been implemented mainly for large-bore welded piping, but in the case of small-bore welded piping, post-welding stress improvement measures are often not possible due to dimensional restrictions, etc. Therefore, knowing the actual welding residual stresses of small-bore welded piping regardless of reactor type is essential for the safe and stable operation of nuclear power stations, but there are only a limited number of examples of measuring the residual stresses. In this study, austenitic stainless steel pipes with an outer diameter of 100 mm and a wall thickness of 11.1 mm were butt-welded. The residual stresses were measured by the strain scanning method using neutrons. Furthermore, to obtain detailed residual stresses near the penetration bead where the maximum stress is generated, the residual stresses near the inner surface of the weld were measured using the double-exposure method (DEM) with hard X-rays of synchrotron radiation. A method using a cross-correlation algorithm was proposed to determine the accurate diffraction angle from the complex diffraction patterns from the coarse grains, dendritic structures, and plastic zones. A quantum beam hybrid method (QBHM) was proposed that uses the circumferential residual stresses obtained by neutrons and the residual stresses obtained by the double-exposure method in a complementary use. The residual stress map of welded piping measured using the QBHM showed an area where the axial tensile residual stress exists from the neighborhood of the penetration bead toward the inside of the welded metal. This result could explain the occurrence of stress corrosion cracking in the butt-welded piping. A finite element analysis of the same butt-welded piping was performed and its results were compared. There is also a difference between the simulation results of residual stress using the finite element method and the measurement results using the QBHM. This difference is because the measured residual stress map also includes the effect of the stress of each crystal grain based on elastic anisotropy, that is, residual micro-stress.

Colloidal quantum dots (QDs) have emerged as promising materials for the development of infrared photodetectors owing to their tunable band gaps, cost-effective manufacturing, and ease of processing. This paper provides a comprehensive overview of the fundamental properties of quantum dots and the operating principles of various infrared detectors. We review the latest advancements in short-wave infrared (SWIR), mid-wave infrared (MWIR), and long-wave infrared (LWIR) detectors employing colloidal quantum dots. Despite their potential, these detectors face significant challenges compared to conventional infrared technologies. Current commercial applications are predominantly limited to the near-infrared and short-wave bands, with medium- and long-wave applications still under development. The focus has largely been on lead and mercury-based quantum dots, which pose environmental concerns, underscoring the need for high-performance, non-toxic materials. Looking forward, the development of large array and small pixel detectors and improving compatibility with readout circuits are critical for future progress. This paper discusses these hurdles and offers insight into potential strategies to overcome them, paving the way for next-generation infrared sensing technologies.

Soft matter and biological materials are characterized by a complex morphology consisting of multiple structural levels that are either hierarchically organized or coexist over a length scale from a few Å up to the size of µm. For a structural characterization of such morphologies, an extended Q-range must be covered in X-ray and neutron scattering experiments. Neutrons offer the unique advantage of contrast variation and matching by D-labeling, which is of great value for the characterization of hydrocarbon systems, which are essentially the constituents of soft matter and biological materials. The combination of ultra- and small-angle neutron scattering techniques (USANS and SANS) on complementary beamlines has long been used for such experimental investigations. However, the combined use of USANS and SANS methods at the same beamline for simultaneous acquisition of scattering data over a wide Q-range is necessary when working with sensitive or expensive samples that require special preparation or in situ treatment during the structural characterization. For this reason, several pinhole SANS instruments have been equipped with focusing lenses to allow additional measurements at lower Q values, in the USANS range. The use of neutron lenses has the additional advantage of enhancing the intensity on the sample by providing the ability to work with larger samples while maintaining the same resolution as in pinhole mode. The experimental approach for using neutron lenses to enhance the intensity and extend the Q-range to lower values than in pinhole mode is presented using examples from studies on the pinhole SANS diffractometers equipped with focusing lenses.

The interaction of pulsed lasers with matter involving nanomaterials as a pure target or thin layer deposited on a target initiates transient plasma, which shows strong enhancement in a spectral line emission. This domain of research has been explored via two well-established techniques dubbed NELIBS and NELIPS. These Nano-Enhanced Laser-Induced Breakdown or Plasma Spectroscopy techniques entail similarities as well as differences. The newly defined concept of Nano-Enhanced Laser-Induced Plasma Spectroscopy NELIPS is introduced. Thereupon, certain confusion has arisen from various aspects of the similarities as well as differences between the two techniques. In this article, we will investigate the application of either technique to retrieve relevant data about the enhanced spectral line plasma emission phenomenon. To discriminate between these two techniques, a survey on the nature of the target, the origin of enhancement and prevalent theoretical approaches is presented. In this context, the potential achievements, challenges and expected prospects are comparatively highlighted. This review emphasizes the unique contributions of NELIPS, particularly the advanced approach in nanoscale thermal modeling and spectroscopic applications.

One technique for sintering green compacts and imparting the required qualities to meet the specific application requirements is spark plasma sintering (SPS). This study examines the effects of SPS parameters (sintering temperature and pressure, holding time, and heating rate) and plantain peel ash (PPA) reinforcement concentrations (0, 5 wt%, 10 wt%, 15 wt%, and 20 wt%) on the microstructure, compressive strength, and wear characteristics of the fabricated Al–Mg–PPA composites. As a result of the ball milling machine’s high efficiency, the PPA reinforcement was evenly dispersed throughout the aluminum matrix after 90 min of milling. At lower sintering temperatures and pressures, microstructural flaws such as weak grain boundaries, micro-pores, and micro-cracks were more noticeable than at higher ones. The PPA reinforcement and magnesium powder (wetting agent) increased the composites’ compressive strength by improving the wettability between the PPA reinforcement and the Al matrix. At a weight fraction of 5 wt% PPA, the maximum compressive strength of 432 MPa was attained for the sintered composites, which is a 222% improvement over the sintered aluminum matrix. Additionally, the PPA reinforcement enhanced the wear properties of the sintered Al–Mg–PPA composites by reducing the wear loss. Increasing the wear load resulted in a higher wear rate. The COF for the sintered composites ranges from 0.049 to 0.727. The most consistent correlation between the wear rate and the COF is that as the wear rate decreases, the COF decreases, and vice versa. Abrasive wear was the dominant wear mechanism observed. Tear ridges, shear steps, micro-voids, and cleavages were seen on the composites’ fracture surfaces, an indication of a ductile-brittle fracture.

This work demonstrates a high-quality erbium-doped fiber (EDF) ring laser in the L-band gain range by combining the Rayleigh backscattering (RB) feedback signal and unpumped EDF induced saturable absorber (SA) filter. The optical filter effect induced by the RB feedback injection and EDF SA could generate single-longitudinal-mode (SLM) behavior and shrink the linewidth to sub-kHz. The output linewidth, power, and optical-signal-to-noise ratio (OSNR) of the fiber ring laser were also shown within the 42 nm wavelength bandwidth of 1565.0 to 1607.0 nm. Also, the instabilities of output power and central wavelength of each lasing lightwave were analyzed with a measurement time of 45 min.