Anton Paar (United States)

The temporomandibular joint (TMJ) and the knee joint are two of the most frequently used joints in the body, with the mandibular condylar cartilage (MCC) and the articular cartilage (AC) covering the joint bone surfaces, respectively. Compromised MCC functions lead to various temporomandibular disorders (TMD), including TMJ osteoarthritis (TMJ OA); however, the mechanisms governing MCC homeostasis and its biomechanical properties are still poorly understood. In this study, we comprehensively compared the biological and biomechanical features of the MCC and AC in mice. Histological analysis on P1, P21, 3-month, and 10-month mice revealed the most drastic structural differences between MCC and AC at occlusion establishment (P21), with MCC found to be more susceptible to age-associated cartilage degeneration. Immunostaining revealed differentially distributed cartilage extracellular matrix components in MCC and AC, including collagen type I, II, and X, and highly enriched expression of several key transcriptional factors at the posterior region of the MCC, including sex determining region Y-box 9 (SOX9), runt-related transcription factor 2 (RUNX2), and scleraxis (SCX). The posterior MCC also houses a group of long-lasting, slow-proliferative cells, as evidenced by the BrdU/EdU incorporation assay, suggesting the presence of a potential stem/progenitor cell niche at the posterior TMJ. Unbiased nanoindentation analysis revealed distinct biomechanical features between these joint cartilages. MCC exhibits a significantly lower elastic modulus (E IT ) than AC, with the highest E IT observed at the anterior TMJ, which is oppositely associated with the fibrous layer thickness, but positively correlated with the ratio of the collagen type X-positive matrix in the cartilaginous layer. Altogether, this study provides a basic understanding of the biological and biomechanical features of the cartilaginous tissues in two important joints, which may facilitate our understanding of the physiology in the TMJ and knee joint, and support the applications of mouse models to study TMJ dysfunctions.

Systems driven far from equilibrium often retain structural memories of their processing history. This memory has, in some cases, been shown to dramatically alter the material response. For example, work hardening in crystalline metals can alter the hardness, yield strength, and tensile strength to prevent catastrophic failure. Whether memory of processing history can be similarly exploited in flowing systems, where significantly larger changes in structure should be possible, remains poorly understood. Here, we demonstrate a promising route to embedding such useful memories. We build on work showing that exposing a sheared dense suspension to acoustic perturbations of different power allows for dramatically tuning the sheared suspension viscosity and underlying structure. We find that, for sufficiently dense suspensions, upon removing the acoustic perturbations, the suspension shear jams with shear stress contributions from the maximum compressive and maximum extensive axes that reflect or “remember” the acoustic training. Because the contributions from these two orthogonal axes to the total shear stress are antagonistic, it is possible to tune the resulting suspension response in surprising ways. For example, we show that differently trained sheared suspensions exhibit (1) different susceptibility to the same acoustic perturbation, (2) orders of magnitude changes in their instantaneous viscosities upon shear reversal, and (3) even a shear stress that increases in magnitude upon shear cessation. We work through these examples to explain the underlying mechanisms governing each behavior. Then, to illustrate the power of this approach for controlling suspension properties, we demonstrate that flowing states well below the shear jamming threshold can be shear jammed via acoustic training. Collectively, our work paves the way for using acoustically induced memory in dense suspensions to generate rapidly and widely tunable materials. Published by the American Physical Society 2024

The properties of multiphase flows are challenging to measure, and yet effective properties are fundamental to modelling and predicting flow behaviour. The current study is motivated by rheometric measurements of a gas-fluidized bed using a coaxial rheometer in which the fluidization rate and the rotational speed can be varied independently. The measured torque displays a range of rheological states: quasistatic, dense granular flow behaviour at low fluidization rates and low-to-moderate shear rates; turbulent toroidal-vortex flow at high shear rates and moderate-to-high fluidization rates; and viscous-like behaviour with rate-dependent torque at high shear rates and low fluidization or at low shear rates and high fluidization. To understand the solid-like to fluid-like transitions, additional experiments were performed in the same rheometer using single-phase liquid and liquid–solid suspensions. The fluidized bed experiments are modelled as a Bingham plastic for low fluidization rates, and as a shear-thinning Carreau liquid at high fluidization rates. The suspensions are modelled using the Krieger–Dougherty effective viscosity. The results demonstrate that, by using the effective properties, the inverse Bingham number marks the transition from solid-like to viscous-flow behaviour; a modified gap Reynolds number based on the thickness of the shear layer specifies the transition from solid-like to turbulent vortical flow; and a gap Reynolds number distinguishes viscous behaviour from turbulent vortical flow. The results further demonstrate that these different multiphase flows undergo analogous flow transitions at similar Bingham or Reynolds numbers and the corresponding dimensionless torques show comparable scaling in response to annular shear.

Dynamic mechanical analysis (DMA) applies an oscillating force to a specimen and analyzes the rheological and viscoelastic properties of a material. Since this method is used to characterize the frequency-dependent viscoelastic properties, it is mostly used for polymers, which have high sensitivity to the loading frequency. Cementitious composites are brittle and require more attention to specimen preparation and experimental settings to obtain reliable results. This work develops a DMA test protocol for cementitious composites which includes analyzing the effect of preload test, frequency pretest, and amplitude sweep on properties of cementitious composites. We propose a statistical method to analyze the variation between samples and determine the outliers among the specimens with the same mix to obtain valid test results from a sample group. The dynamic results obtained by using the proposed method are also discussed to serve as the baseline. The experimental setup parameters and statistical analysis presented in this work can be a robust foundation for the DMA analysis of cementitious composites.

Silicon-incorporated diamond-like carbon (Si-DLC), an amorphous material containing Si atoms with sp3- and sp2-hybridized carbon, is a promising biomaterial for versatile biomedical applications due to its excellent mechanical properties, chemical inertness, biocompatibility, and antimicrobial capability. However, the antifungal properties of plasma-treated Si-DLC have not been systematically evaluated. In this study, Si-DLC coatings were deposited by chemical vapor deposition and further treated with either oxygen or fluorine plasma to render the surface anchored with different functional groups and hydrophobicity. Surface roughness was probed with atomic force microscopy, whereas bonding character and surface composition were assessed using Raman and X-ray photoelectron spectroscopy. Wettability and surface charge were investigated via water contact angle and zeta potential measurements. Antifungal assessment was performed using a Candida albicans multi-well plate screening technique and crystal violet biomass quantification. The results demonstrate that oxygen plasma–treated Si-DLC exhibited hydrophilic properties, lower negative zeta potential, and significant antifungal behavior. This material can potentially be applied on surfaces for the prevention of reduced nosocomial infections.