- Book Chapter
- 10.1007/978-3-658-47181-1_6
7 Handlungsempfehlungen
- Jan 01, 2025
- Rüdiger Maas + 1 more +1
Publications from 2021 to 2026
Showing 10 of 11 papers
7 Handlungsempfehlungen
Erklärungsansätze
Methodology and Database for the Quantification of the Technical Recyclability of Electrical and Electronical Equipment Demonstrated on a Smartphone Case Study
Assessing a given product’s design and its recyclability using mass flow analysis based on the material separation and recovery rates of individual recycling processes under realistic conditions can support design decisions promoting better recyclability. EN 45555 defines the calculation of the technical recyclability of electrical and electronic equipment (EEE). However, the lack of specific recycling rates for material or processes often leads to either too small or too high recyclability values. Herein, an extensive database of such recycling rates is presented. Moreover, the quality of recycling is considered. The typical classification into “recycled” and “lost” is expanded into four categories, namely “circular”, “recycled”, “alternate material recovery” and “lost”. The recycling rate database includes yields for all four categories and covers 30 materials for 14 recycling processes relevant in waste EEE (WEEE) treatment. These data enable a detailed calculation of the recyclability of various EEE for multiple recycling scenarios covering the entire WEEE recycling chain. Fraunhofer IZM performed an internal critical review of the data. The recycling rates database can act as a solid foundation for comparing the recyclability of various electronics in different scenarios and recyclability indices. For example, the recyclability of typical smartphones is investigated comparing different dismantling and recycling scenarios highlighting the potential of both database and methodology.
Read moreScheduling System for Remote Control of Instruments used for Atmospheric Observation
In this poster contribution, we present a scheduling system for automated remote operation of instruments at high-altitude research facilities and similar remote sites. Via web-based interfaces, the system allows instrument owners as well as authorized third-party scientists to schedule and execute measurements and observations.The system has been developed as a thesis project in the context of the AlpEnDAC-II ("Alpine Environmental Data Analysis Centre", www.alpendac.eu) collaboration (funded by the Bavarian State Ministry of the Environment and Consumer Protection). Consequently, the scheduler and interfaces have been integrated with the AlpEnDAC Operating-on-Demand functionalities. A first use case for the framework has been the operation of an airglow imager (FAIM) in Oberpfaffenhofen (DE).We describe the design and implementation of our system for scheduling and execution of multi-user observations on instruments, including scheduling-data transfers and data retrieval. Our core implementation uses an optimization-based scheduler (Google's OR-Tools) to ensure maximum instrument use and to minimize idle times. Results show that the scheduler is reliable, fast, and is consistently able to provide optimal observation plans. The extensibility of the system is guaranteed by the usage of modern software in the core of the system, including well-defined and specified communication through REST APIs. Thus, it can easily be adapted to other settings and instruments, which is also facilitated by a modern deployment strategy using Docker and Kubernetes.
Read moreContext-Specific, User-Centred: Designing Urban Green Infrastructure to Effectively Mitigate Urban Density and Heat Stress
<p>Green infrastructure plays a vital role for cities facing the challenges of urbanisation and climate change. It has the potential to mitigate the adverse effects of urban density and the heat island effect, enhancing the ecological and social resilience of cities and their inhabitants. This study identifies contextual, psychological, and social factors which influence people’s subjective evaluation of urban green infrastructure (UGI), density, and heat stress. Planning recommendations for effective, context-specific, user-centred design are developed to increase the social and health benefits of UGI in limited space. To do so, a mixed-methods approach that combines social surveys, GIS-analysis, and microclimate modelling was employed. The field studies were undertaken in two contrasting neighbourhoods in Munich, Germany: a densely built and scarcely vegetated inner-city neighbourhood and a declaimed “green and compact” neighbourhood at the outskirts. Both sites are assessed in terms of their supply of green infrastructure, building and population density, and outdoor summer heat loads drawing on geostatistical data and mean radiant temperature modelling. This assessment is compared to the inhabitants’ subjective evaluation thereof retrieved from face-to-face questionnaires, and semi-standardised interviews. The results indicate that the existence and the amount of UGI per se are not decisive for people’s perception of urban heat, density, and neighbourhood attractiveness. It is rather the perceived accessibility of green spaces, their design, quality, and contextual factors like traffic or the presence of other people that define its value for urban dwellers.</p>
Read moreBiowaste Treatment and Waste-To-Energy—Environmental Benefits
Biowaste represents a significant fraction of municipal solid waste (MSW). Its separate collection is considered as a useful measure to enhance waste management systems in both the developed and developing world. This paper aims to compare the environmental performance of three market-ready technologies currently used to treat biowaste—biowaste composting, fermentation, and biowaste incineration in waste-to-energy (WtE) plants as a component of residual municipal solid waste (RES). Global warming potential (GWP) was applied as an indicator and burdens related to the operation of facilities and credits obtained through the products were identified. The environmental performance of a WtE plant was investigated in detail using a model, implementing an approach similar to marginal-cost and revenues, which is a concept widely applied in economics. The results show that all of the treatment options offer an environmentally friendly treatment (their net GWP is negative). The environmental performance of a WtE plant is profoundly affected by its mode of its operation, i.e., type of energy exported. The concept producing environmental credits at the highest rate is co-incineration of biowaste in a strictly heat-oriented WtE plant. Anaerobic digestion plants treating biowaste by fermentation produce fewer credits, but approximately twice as more credits as WtE plants with power delivery only.
Read moreAn artifact-minimizing method for total dust sampling and chemical characterization of industrial high-temperature aerosols
ABSTRACTConventional methods for total dust sampling from industrial high-temperature aerosols containing condensable species, e.g., in boilers of municipal solid waste incinerators (MSWI), are always influenced by condensation artifacts. Therefore, we extended the scope of a previously developed probe intended for size-fractionated aerosol sampling with reduced artifacts and employed it for total dust measurements. The dust is collected on quartz fiber filters, which are gravimetrically evaluated and chemically analyzed by energy dispersive X-ray spectroscopy and wet-chemical methods. First measurements in the boiler of an MSWI confirm that the probe is also suitable for artifact-minimized total dust sampling. The data are consistent with results from measurements with the size-fractionating method conducted in parallel. By combining the results of both sampling methods, we reveal the average chemical composition of the submicron particles in the aerosol, which is not accessible by one of the two methods...
Read moreApplication of two-dimensional gas chromatography combined with pixel-based chemometric processing for the chemical profiling of illicit drug samples
Comprehensive Gas Chromatography−Time-of-Flight Mass Spectrometry Using Soft and Selective Photoionization Techniques
The hyphenation of gas chromatography and mass spectrometry (GC/MS) revolutionized organic analysis. In GC/MS coupling, usually electron impact ionization is applied, and molecules are identified by their fragment pattern. Although mass spectrometry in principle is a separation method, it is used predominantly as a spectrometric technique. However, if soft (i.e., fragmentation-free) ionization techniques are applied, the inherent separation character of MS is emphasized, which has similarities to a GC boiling point separation. By combining polar column GC separation and fast soft ionization time-of-flight mass spectrometry technology, a comprehensive separation of complex petrochemical samples can be obtained (GC x MS approach). Compounds of comparable physical-chemical properties are characteristically grouped together in a two-dimensional retention time-m/z representation. This resembles the separation characteristics of comprehensive two-dimensional gas chromatography (GC x GC) and, thus, represents a novel multidimensional separation approach. In this work, a gas chromatograph equipped with a polar separation column was coupled to a home-built laser ionization time-of-flight mass spectrometer. Laser-based, single-photon ionization was used for universal soft ionization and resonance-enhanced multiphoton ionization for selective ionization of aromatic compounds. A novel capillary-jet inlet system was used for the coupling. Multidimensional comprehensive analysis of complex petrochemical hydrocarbon samples using gas chromatography coupled to mass spectrometry with soft and selective photo ionization sources is first demonstrated.
Read moreA mobile mass spectrometer for comprehensive on-line analysis of trace and bulk components of complex gas mixtures: parallel application of the laser-based ionization methods VUV single-photon ionization, resonant multiphoton ionization, and laser-induced electron impact ionization.
A newly developed compact and mobile time-of-flight mass spectrometer (TOFMS) for on-line analysis and monitoring of complex gas mixtures is presented. The instrument is designed for a (quasi-)simultaneous application of three ionization techniques that exhibit different ionization selectivities. The highly selective resonance-enhanced multiphoton ionization (REMPI) technique, using 266-nm UV laser pulses, is applied for selective and fragmentationless ionization of aromatic compounds at trace levels (parts-per-billion volume range). Mass spectra obtained using this technique show the chemical signature solely of monocyclic (benzene, phenols, etc.) and polycyclic (naphthalene, phenathrene, indol, etc.) aromatic species. Furthermore, the less selective but still fragmentationless single photon ionization (SPI) technique with 118-nm VUV laser pulses allows the ionization of compounds with an ionization potential below 10.5 eV. Mass spectra obtained using this technique show the profile of most organic compounds (aliphatic and aromatic species, like nonane, acetaldehyde, or pyrrol) and some inorganic compounds (e.g., ammonia, nitrogen monoxide). Finally, the nonselective ionization technique laser-induced electron-impact ionization (LEI) is applied. However, the sensitivity of the LEI technique is adjusted to be fairly low. Thus, the LEI signal in the mass spectra gives information on the inorganic bulk constituents of the sample (i.e., compounds such as water, oxygen, nitrogen, and carbon dioxide). Because the three ionization methods (REMPI, SPI, LEI) exhibit largely different ionization selectivities, the isolated application of each method alone solely provides specific mass spectrometric information about the sample composition. Special techniques have been developed and applied which allow the quasi-parallel use of all three ionization techniques for on-line monitoring purposes. Thus, a comprehensive characterization of complex samples is feasible jointly using the characteristic advantages of the three ionization techniques. Laboratory applications show results on rapid overview characterization of mineral oil-based fuels and coffee headspace. The first reported field applications include timely resolved on-line monitoring results on automobile exhausts and of waste incineration flue gas.
Read more