- Research Article
- 10.1016/j.vacuum.2026.115132
Erosion of cathode materials with different melting points in a pulsed vacuum arc
- Apr 01, 2026
- Vacuum
- G Yu Yushkov + 3 more +3
Publications from 2021 to 2026
Showing 10 of 497 papers
Erosion of cathode materials with different melting points in a pulsed vacuum arc
Microstructure and mechanical properties of Ti-B-C coatings produced by dual pulsed magnetron sputtering of TiB2 and graphite targets
The influence of peak current and pulse duration on the ion-to-atom ratio in high-power impulse magnetron sputtering
On the Electrical Strength of the Accelerating Gap in a Forevacuum Plasma Electron Source
Some aspects determining the electrical strength of the accelerating gap in a fore-vacuum-pressure plasma-cathode electron beam source utilizing helium and argon as the working gas were explored. Penetration of plasma into the accelerating gap is the cause of breakdown. We find that gap breakdown occurs at larger emission hole diameter and at higher plasma density in helium than in argon. The greater stability of the plasma boundary in helium is explained by the observed greater anode potential drop and consequently greater sheath thickness.
Read moreOptical Characteristics and Mass-charge Composition of Plasma of a Pulsed Vacuum Arc Discharge with a Magnesium Cathode
The results of the study of the elemental and charge composition of the plasma of a vacuum arc discharge with a cathode made of magnesium Mg are presented. Time-of-flight spectrometry was used to determine the mass-charge composition of the ion current extracted from the vacuum arc plasma. The spectral characteristics of the discharge plasma were studied by recording the power density distribution of its radiation in the optical spectral range. Both methods were used simultaneously, so that a high level of identity was maintained not only in the operating conditions of the vacuum arc, but also in the true composition of the plasma of the cathode spots, which are the elementary cells of the structure of such a discharge. It was found that the fractions of heavy charged particles, represented by single- (Mg+) and double-charged (Mg2+) magnesium ions, in the beam extracted from the expanding plasma, depend significantly on the average energy deposited in the discharge. With the increase of the average energy the fraction of Mg2+ decreased, while that of Mg+ increased. In turn, the relative amplitudes of the lines of ions (Mg II and Mg III) and atoms (Mg I) of magnesium in the emission spectra of the plasma of cathode spots did not depend on the discharge energy characteristics. Based on the obtained results, reasoning is given about the mutual complementarity of the methods used and the further development of methods for diagnostics of cathode arc plasma.
Read moreEffect of Zr and Cu Alloying on the Structure and Electrochemical Properties of TiNi
The detailed comparative XRD, TEM/EDS analysis of TiNi and TiNiCuZr samples revealed the formation of two isostructural B2 phases with different lattice parameters, chemical composition and microstructure. According to the experimental the lattice parameter value aB2(TiNiCuZr) in the TiNiCuZr sample is several times higher than aB2(TiNi) in the TiNi sample, indicating the formation of a new B2 phase. These variations in B2 lattice parameters strongly correlate with the changes in the chemical composition. The study of the electrochemical properties of the initial alloys (TiNi, Ti–Ni–Cu–Zr) in 0.9 wt % NaCl and artificial saliva showed that the TiNi alloy of binary composition exhibits significantly higher corrosion properties. In turn, the Ti–Ni–Cu–Zr alloy is prone to anodic polarization and corrosion destruction. It was found that under the same conditions of the corrosive media, the corrosion rate of the Ti–Ni–Cu–Zr alloy is ∼3.2 times higher than that of the TiNi alloys.
Read moreStructure and Properties of Titania Coatings Formed by the Plasma-Assisted Vacuum Arc Method
Titania coatings have been formed by the plasma-assisted vacuum arc deposition, and their structure, phase composition, and properties have been studied in detail. It has been shown that the discharge current of the gas plasma source is a key parameter for controlling the polymorphic composition, hardness, and wear resistance of the titania coating. Titania is present in the coatings in two polymorphs, namely, rutile and anatase; their relative content depends on plasma assistance conditions. Titania coatings, regardless of the plasma assistance mode, are a nanocrystalline material with a columnar structure.
Read moreDischarge Plasma Parameters of Magnetron Sputtering System in Gas and Vacuum (Gasless) Operating Modes
We present the results of probe measurements of plasma parameters and ion mass-to-charge state of a DC magnetron sputtering system (MSS) in gas and vacuum (gasless) operating modes at operating pressures from 2 down to 0.05 mTorr. It is shown that, in comparison with the gas operating mode, the discharge plasma of the vacuum magnetron is characterized by higher values of electron temperature and plasma potential, along with the generation of multiply charged metal ions of the target material. This mode is also characterized by a higher degree of ionization of sputtered material and enhanced ion current density onto the substrate. The revealed differences may be useful for improving quality and properties of formed coatings.
Read moreFeatures of the Formation and Propagation of Plasma Diffuse Jets
Plasma diffuse jets (PDJ) with a length of over 100 cm were generated using a capacitive discharge in a quartz tube with ring electrodes. It was determined that the electrode installation location of ring electrodes does not affect the characteristics of PDJ in air and nitrogen. It was established that PDJ emissions primarily consist of the (1+) and (2+) nitrogen bands. When spectra were recorded in the interelectrode region, the (1−) nitrogen bands also appeared in the spectrum. At pressures below 0.1 Torr, spectral lines from the dissociation products of water vapor (CO, OH, and H) emerged, affecting the discharge plasma glow color. Spectra of PDJ were obtained at lower frequencies than those previously studied. At a frequency of 1 Hz, no discharge formation was observed. However, as the frequency increased to 1 kHz, PDJ began to form. It was found that the PDJ color was redder at negative voltage pulse polarity than at positive one, as confirmed by emission spectra from the diffuse jet body. It was shown that within the range of 3 to 21 cm from the outer edge of the ring electrode, the velocity of the first ionization wave (IW) propagating to the left of the electrodes was lower than that of the IW propagating to the right. This phenomenon is explained by a decrease in plasma potential with increasing distance from the high-voltage electrode due to the finite conductivity of the discharge plasma, as the registration region on the left was farther from the high voltage electrode than the corresponding region on the right.
Read moreVortex Electron Flows in Magnetically Insulated Transmission Lines of Megaampere Pulse Generators with Low-Impedance Loads: Numerical Simulation
Numerical experiment using KARAT electromagnetic PiC code demonstrated а vortex structure of electron flows arising in magnetically insulated lines with an inductive load, fed with sub-microsecond megaampere current pulse, under condition of space charge limited electron emission from the line conductors. It was found that no significant energy loss is associated with the electron vortices. Additional space charge-limited emission of positive heavy ions does not make the losses critical but causes degradation of the vortex structure as the ions accumulate. The vortices can reach the separating insulator, producing a threat to its electrical strength. Closing a shortening switch installed at the entrance of the vacuum segment of the line provides effective interception of the electron flows. Intense sub-gigahertz voltage oscillations have been observed in the nonuniform lines, apparently excited by the moving electron vortices.
Read more