- Research Article
- 10.1016/j.fusengdes.2026.115723
Heuristic Bi-directional transition-based RRT for CMOR motion planning in the constrained CFEDR vacuum vessel
- Jun 01, 2026
- Fusion Engineering and Design
- Chenhui Wan + 7 more +7
Publications from 2021 to 2026
Showing 10 of 1,209 papers
Heuristic Bi-directional transition-based RRT for CMOR motion planning in the constrained CFEDR vacuum vessel
Study on the 4 K thermal conductivity of epoxy composites for fusion magnets
Improvement of the neutron flux detector structural design for EAST
Femtosecond-laser-induced highly regular grating nanostructures: Spatiotemporal control routes for near-field enhancement on metallic glass surfaces
Linear gyrokinetic simulations of fast-ion effects on the transition of the dominant electrostatic instability from TEM to ITG in EAST
Abstract Linear gyrokinetic simulations have been performed using the GTC code to investigate the effects of fast ions on dominant instability changes from TEM to ITG in the EAST. The effects of fractions (5%, 7.5%, and 10%) and temperatures (10 keV, 20 keV, and 30 keV) of fast ions are investigated. The dominant mode transitions from trapped electron mode (TEM) to ion temperature gradient (ITG) mode under different plasma parameters. A transition of the dominant instability is observed at 0.7 ≤ kθρs ≤ 0.8 and shifts to kθρs ≈ 0.7 when fast ions are considered. In addition, fast ions stabilize ITG modes, and the effect becomes more significant as the fraction of fast ions increases, reducing the growth rate by approximately 10% when the fraction of fast ions is 10%. The stabilizing effect increases with increasing temperature of fast ions, but varies little for Tf > 20 keV. Fast ions reduce the ion temperature gradient R/LTi threshold of the dominant instability changes from TEM to ITG. The threshold decreases with decreasing temperature of fast ions, with a reduction of about 10%-20% when the fraction reaches 10% in hydrogen plasmas, and about 3%-12% when deuterium is the main ion. Furthermore, the normalized electron temperature gradient R/LTe for the dominant instability changes from ITG to TEM is lower in hydrogen plasmas, decreasing from 5.4 to 4.1 as Tf increases from 10 keV to 30 keV, while in deuterium plasmas it decreases from 10.5 to 9.5. Moreover, electron–electron collisions lead to the dominant instability changes from TEM to ITG at 0.4 ≤ kθρs ≤ 0.8 and strongly stabilize the ITG mode, reducing its growth rate about 50%, while ion–ion collisions have little influence on TEM and ITG.
Read moreEAST plasma equilibrium reconstruction based on weight-adaptive physics-informed neural network
A novel Pre-HIP two-step annealing process for enhancing the critical current of Ba1-xKxFe2As2 superconducting tapes
In situ fabrication of ultrathin δ-MnO2 nanosheet-decorated MWCNTs for efficient electrochemical uranium extraction
Multi-machine validation of plasma initiation modelling and prospects for future devices: Predicting plasma initiation using only hardware design and control room input data
Abstract This paper reports on the generic prediction capability of full electromagnetic plasma initiation modelling with DYON, which was carried out for the first time in fusion research by the joint modelling of the International Tokamak Physics Activity—Integrating Operation Scenario group. The following devices were included in the experiment database: VEST (spherical torus, copper coils, Stainless steel wall, R / a = 0.3 m/0.2 m, V v = 3.7 m 3 ), MAST-U (spherical torus, copper coils, C wall, R / a = 0.7 m/0.5 m, V v = 55 m 3 ), EAST (conventional tokamak, superconducting coils, metallic wall, R / a = 1.85 m/0.5 m, V v = 38 m 3 ), DIII-D (conventional tokamak, copper coils, C wall, R / a = 1.67 m/0.65 m, V v = 35 m 3 ), and KSTAR (conventional tokamak, superconducting coils, C wall, R / a = 1.8 m/0.5 m, V v = 55 m 3 ). Despite the different hardware features of the devices, the required operating spaces of the loop voltage induction and prefill gas pressure for inductive plasma initiation in each device were successfully reproduced by the predictive simulations with DYON using only the individual hardware design and the control room input data for each discharge. This successful validation across multiple machines demonstrates that the full electromagnetic DYON modelling can capture the essential physics of inductive plasma initiation. The simulation settings commonly employed for all modelling and the modifications necessary to account for the discrepancies between individual devices are reported. Predictions for ITER based on the multi-machine validation indicate that a wide range of prefill gas pressures exists for the Townsend breakdown and the plasma burn-through (0.01–1.5 mPa).
Read morePlasma synthesis ultra-thin carbon coated PtFe alloys on N-doped graphene-CNT composite for methanol electrooxidation