- Conference Article
- 10.1109/estc60143.2024.10712071
Scatterometry Application on Cu/SiCN Surface Topography Towards High Volume Manufacturing
- Sep 11, 2024
- Soon Aik Chew + 11 more +11
Publications from 2021 to 2026
Showing 10 of 12 papers
Scatterometry Application on Cu/SiCN Surface Topography Towards High Volume Manufacturing
Development of SiGe Indentation Process Control for Gate-All-Around FET Technology Enablement
Methodologies for characterization of the lateral indentation of silicon-germanium (SiGe) nanosheets using different non-destructive and in-line compatible metrology techniques are presented and discussed. Gate-all-around nanosheet device structures with a total of three sacrificial SiGe sheets were fabricated and different etch process conditions used to induce indent depth variations. Scatterometry with spectral interferometry and x-ray fluorescence in conjunction with advanced interpretation and machine learning algorithms were used to quantify the SiGe indentation. Solutions for two approaches, average indent (represented by a single parameter) as well as sheet-specific indent, are presented. Both scatterometry with spectral interferometry as well as x-ray fluorescence measurements are suitable techniques to quantify the average indent through a single parameter. Furthermore, machine learning algorithms enable a fast solution path by combining x-ray fluorescence difference data with scatterometry spectra, therefore avoiding the need for a full optical model solution. A similar machine learning model approach can be employed for sheet-specific indent monitoring; however, reference data from cross-section transmission electron microscopy image analyses are required for training. It was found that scatterometry with spectral interferometry spectra and a traditional optical model in combination with advanced algorithms can achieve a very good match to sheet-specific reference data.
Read moreReliability Challenges and Inline Metrology - An Effective Approach to Implementation in Advanced Devices
As semiconductor devices scale down in size, the sensitivity of reliability to process variation increases. This increase is due to the high-reliability requirements for advanced system applications, the narrowing process margins, and the high sensitivity of devices to composition. At the process level, specific materials or process chambers can degrade the devices' reliability, induced by additional charge traps in the adjacent cells and poor data retention due to contamination by killer elements and complex structures, although they may be required from a process integration perspective. It is difficult to effectively detect killer elements during the process, which can create or accelerate reliability failure. Several killer elements cause reliability degradation: F (fluorine), CI (Chlorine), local strains in the SiGe layers, and plasma-induced traps at the gate oxide interfaces. We find that an effective approach to prevent reliability failure is to monitor potential killer elements in the process, maintain them under threshold levels and screen out heavily contaminated wafers before wafer fab-out. This paper addresses the relationship between specific killer elements and reliability and reviews the enablers of inline metrology that can prevent reliability failure by early detection and monitoring of variation of killer elements in fabs.
Read moreMachine learning and hybrid metrology using scatterometry and LE-XRF to detect voids in copper lines
Voids in copper lines are a common failure mechanism in the back end of line (BEOL) of integrated circuits manufacturing, affecting chip yield and reliability. As subsequent process nodes continue to shrink metal line dimensions, monitoring and control of these voids gain more and more importance [1]. Currently, there is no quantitative in-line metrology technique that allows voids to be identified and measured. This work aims to develop a new method to do so, by combining scatterometry (also referred to as Optical Critical Dimension or Optical CD) and low-energy x-ray fluorescence (LE-XRF), as well as machine learning techniques. By combining the inputs from these tools in the form of hybrid metrology, as well as with the incorporation of machine learning methods, we create a new metric, referred to as <i>V<sub>xo</sub></i>, to characterize the quantity of void. Additionally, the results are compared with inline electrical test data, as higher amounts of voids were expected to increase the measured resistivity. This was not found to be the case, as the impact of the voids was much less of a factor than variation in the cross-sectional area of the lines.
Read moreHybrid metrology universal engine: co-optimization
In recent years Hybrid Metrology has emerged as an option for enhancing the performance of existing measurement toolsets and is currently implemented in production<sup>1</sup>. Hybrid Metrology is the practice to combine measurements from multiple toolset types in order to enable or improve the measurement of one or more critical parameters. While all applications tried before were improved through standard (sequential) hybridization of data from one toolset to another, advances in device architecture, materials and processes made possible to find one case that demanded a much deeper understanding of the physical basis of measurements and simultaneous optimization of data. This paper presents the first such work using the concept of co-optimization based hybridization, where image analysis parameters of CD-SEM (critical dimensions Scanning Electron Microscope) are modulated by profile information from OCD (optical critical dimension – scatterometry) while the OCD extracted profile is concurrently optimized through addition of the CD-SEM CD results. Test vehicle utilized in this work is the 14nm technology node based FinFET High-k/Interfacial layer structure.
Read moreMueller matrix characterization using spectral reflectometry
The fast evolution of microelectronics fabrication technology demands a concurrent development in metrology capabilities. In recent years, Mueller Matrix (MM) scatterometry has been asserted as a useful tool in characterizing critical dimensions (CD) in periodical arrays of nanometer-size structures. Specifically, some symmetry properties of the measured structure can be readily extracted from the MM, allowing effective isolation of abnormal features. One example is measuring deviations of grating structures from perfect mirror symmetry, characteristic of faults in the fabrication process. The most general form of the Muller matrix requires 16 independent measurements, and requires spectral ellipsometry. However, using some very general assumptions on the reflection properties of the measured sample, one can reduce this number considerably. Such realistic assumptions are time independence of the reflection properties, and homogeneity of the sample (i.e., constant reflectivity throughout the measurement spot), as is the common case in optical CD metrology targets. We show that under these assumptions the Mueller matrix can be completely measured using spectral reflectometry. The goal of characterizing asymmetry is then further analyzed, and a new approach for such measurement, based on spectral reflectometry, is presented. Specifically, using spectral differences metrology (SDM), this approach is shown to provide a simpler means to measure the same asymmetry-dependent quantity as targeted today using MM metrology, but requires only two distinct measurements leading to improved throughput.
Read moreHybrid approach to optical CD metrology of directed self-assembly lithography
Directed Self Assembly (DSA) for contact layers is a challenging process in need of reliable metrology for tight process control. Key parameters of interest are guide CD, polymer CD, and residual polymer thickness at the bottom of the guide cavity. We show that Optical CD (OCD) provides the needed performance for DSA contact metrology. The measurement, done with a multi-channel spectroscopic reflectometry (SR) system, is enhanced through elements of a Holistic Metrology approach such as Injection and Hybrid Metrology.
Read moreA holistic metrology approach: multi-channel scatterometry for complex applications
Improvement in metrology performance when using a combination of multiple optical channels vs. standard single optical channel is studied. Two standard applications (gate etch 4x and STI etch 2x) are investigated theoretically and experimentally. The results show that while individual channels might have increased performance for few individual parameters each - it is the combination of channels that provides the best overall performance for all parameters.
Read moreCopper CMP planarity control using ITM
The new interconnect technology, based on copper damascene processes that is soon to enter production, provides a new challenge for production use of in-line metrology. Copper CMP is a challenging process, both due to the varied chemical and physical properties of the materials on the wafer surface, as well as the within-lot and within-wafer incoming metal thickness nonuniformity. However, the role and requirements of integrated metrology for copper CMP have not been completely determined yet. This paper describes new capabilities designed to meet this challenge of copper polish process monitoring. Experimental results, showing measurements of metal-loss and barrier-material residue thickness, obtained with various Reflected Light Spectroscopy systems, are presented and discussed. Also discussed are different schemes of monitoring the polish process, as well as a comparison between the erosion and metal line thickness results obtained with Reflected Light Spectroscopy, to those of a surface profiler.
Read more<title>Manufacturing and inspection of OPC and PSM masks</title>
With optical lithography prevailing into the year 2000, super-resolution processes pose a multitude of new challenges to the lithographer. Isolated to nested feature bias calls for 'pre- distorting' the photomask to compensate for proximity effects and print and etch biases in the mask and wafer manufacturing process. OPC (optical proximity correction) techniques have become a reality for sub-halfmicron lithography, and have initiated many discussions looking at the manufacturability of OPC masks. Regaining the lost DOF (depth of focus) due to ever shorter printing wavelength, and increasing yields by expanding process latitude have many IC manufacturers looking into PSMs (phase shift masks) as a viable but expensive enhancement technique for several [2-6] layers of the total [18-26] device mask set. This paper addresses manufacturability issues of various combinations of 'enhancement' masks.
Read more