- Research Article
1
- 10.1016/j.energy.2025.139055
A local digital twin method for fuel injection process of hydrogen/diesel high pressure co-direct injection engine
- Dec 01, 2025
- Energy
- Fangliang Yang + 7 more +7
Publications from 2021 to 2026
Showing 10 of 15 papers
A local digital twin method for fuel injection process of hydrogen/diesel high pressure co-direct injection engine
In-process Synthesis of a Ag/AgCl/g-C<sub>3</sub>N<sub>4</sub> Ternary Heterojunction Photocatalysts for Plasmon Resonance Enhanced Polishing
Surface plasmon resonance has been generally employed to enhance the photoresponse in typical fields such as energy conversion and chemical sensing. In this study, we propose a plasmon resonance enhanced polishing (PREP) method based on in-process synthesized Ag/AgCl/g-C3N4 ternary heterojunctions, which overcomes three critical bottlenecks in conventional photochemical mechanical polishing including complex ex-process synthesis protocols, short-wavelength-limited photoresponse, and rapid charge carrier recombination. By synergistically integrating localized surface plasmon resonance (LSPR) from Ag nanoparticles with a Z-scheme charge transfer mechanism in the AgCl/g-C3N4 heterojunction, we achieve an expanded light absorption range up to 625 nm and significantly improve the separation efficiency of photogenerated carriers. Experimental results demonstrate that the in-process synthesized heterojunction photocatalysts facilitate a 3.02-fold increase in material removal rate under broad-spectrum solar illumination while maintaining close-to-atomic-level surface roughness (0.37 nm). This work not only provides fundamental insights into the dynamic construction of heterojunction architectures but also opens up new application scenarios of the heterojunction-based plasmon resonance phenomenon.
Read moreNumerical Simulation of Streamer Discharge in Transformer Oil Under Various Ionization Energies
Heat transport and surface functionalization in nanocomposites of boron nitride nanotubes and polyethylene.
This work explores the possibility for improving heat transport in a polymeric, electrical insulating material, such as polyethylene, by adding boron nitride nanotubes - a heat superdiffusive material. We use molecular dynamics simulations to study the nanocomposites formed by addition of the nanotubes to both amorphous and crystalline polyethylene, and also investigate the effect of surface functionalization using a silane coupling agent, which, being covalently attached to both the nanofiller and the polymer matrix, facilitates the heat transport between them. Even though transport is shown to deteriorate in each simulation when the coupling agents are added, they are expected to favor the nucleation of the crystalline regions about the nanotubes, thus significantly boosting heat conduction in the material along their direction.
Read moreResearch on the Control Method of Auto AMT Variable Parameter Shift Process
In order to shorten the power interruption time of the automobile AMT shift process, and restrain the shift shock, aiming at the control problem of the shifting actuator, the AMT variable parameter shift process control strategy is proposed. This method divides the shift process into three stages according to the synchronizer working characteristics, and adopts different control strategies. According to the fuzzy control theory, the fuzzy criterion rules are established to automatically determine the stage boundary point of the synchronizer shift process, and adopt different motor shift control strategies at each stage. It monitors whether the shift process is normal by means of redundant judgment. The test results show that this method can effectively shorten the shift time.
Read moreKinematic analysis and navigation method of a cable-driven continuum robot used for minimally invasive surgery.
Due to the outstanding compliance and dexterity, continuum robot have great advantages in confined space applications, especially in minimally invasive surgery (MIS). However, the vascular environment is complicated and tortuous, it is necessary to preoperative motion planning and navigation for a continuum robot. A cable-driven continuum robot is proposed, and the mapping relationship among the driven space, joint space and task space, as well as the decoupling algorithm are analyzed based on piecewise constant curvature assumption. Moreover, a navigation method is presented to achieve semi-autonomous interventional surgery based on the vascular constraints by using the backbone cure method. Finally, by using the prototype, the interventional simulations and experiments for a simulated glass blood vessel are developed to validate the feasibility and maneuverability of the proposed model and navigation method. The established motion model and navigation method can be used as a motion control and navigation reference.
Read moreTitanium oxide nanoparticle increases shallow traps to suppress space charge accumulation in polypropylene dielectrics
Introduction of surface modified nano-TiO2increases shallow traps and enhances charge carrier mobility so as to suppress space charge accumulation.
Read moreSome Characteristics of Emerging Distribution Systems Considering the Smart Grid Initiative
Flexural Analysis and Design of Strain Softening Fiber-Reinforced Concrete
This paper describes how parameterized material models for strain softening fiber-reinforced concrete are used to express closed-form solutions of moment-curvature response of rectangular cross sections. By utilizing crack localization rules, engineers can predict flexural response of a beam. A parametric study of post crack tensile strength in the strain softening model is conducted to demonstrate general behavior of deflection softening and deflection hardening materials. Uniaxial and flexural test results of several polymeric fiber-reinforced concrete mixtures are used to demonstrate the applicability of the algorithm to predict load-deflection responses. The data are compared with the ASTM International test Method C1599, which represents the residual strength of the sample after cracking has taken place. The simulations reveal that uniaxial tensile stress-strain relationship is under-predicted using the flexural response test results.
Read moreModification to Contribution Factor Formula for Unscheduled Flows
In this letter, modification to an existing formula for determining the contribution of generation companies to unscheduled flows in electric power networks is presented. The enhanced form of the contribution factor formula provides two options for calculating the contribution of generation companies based on the magnitudes of all the minor loop flows and the largest minor loop flow induced, respectively. A numerical example for a modified IEEE 30-bus test system is provided.
Read more