- Research Article
59
- 10.1016/j.jmps.2016.06.015
Mechanics of instability-induced pattern transformations in elastomeric porous cylinders
- Jun 29, 2016
- Journal of the Mechanics and Physics of Solids
- Farhad Javid + 5 more +5
Publications from 2021 to 2026
Showing 10 of 17 papers
Mechanics of instability-induced pattern transformations in elastomeric porous cylinders
A review of vertical motion heave compensation systems
Detailed Emissions Prediction for a Turbulent Swirling Nonpremixed Flame
This paper describes the validation of a previously described CFD-CRN method (computational fluid dynamics-chemical reactor network) for emissions predictions for the laboratory benchmark TECFLAM S09c flame. It details CFD simulation, solution strategy, validation using, CRN generation, detailed emissions predictions and reaction pathway studies. Steady-state 3D CFD models of a 45 degrees sector of the combustor, employing standard numerical techniques; steady-state k-omega SST turbulence, PI radiation, finite-rate eddy-dissipation turbulence-chemistry interaction, and a three-step methane combustion mechanism, were created in ANSYS FLUENT v14. Steady-state models were used as they are of interest to industrial researchers, who are often limited to their use by extremely complex geometries. The models differ in their handling of pressure-velocity coupling and discretization of the momentum equation. The solution which uses SIMPLE coupling and second-order upwind discretization of the momentum equation was generally found to give better results. Satisfactory agreement with experimental profiles for velocity, turbulent kinetic energy, temperature, and species mass fractions has been achieved. Some errors are seen in temperature and CO mass fractions at the highest temperatures (T > 2000 K) and are due to the fact that the highly simplified three-step kinetic mechanism employed due to practical limitations on computational resources, underestimates CO2 dissociation. The results compare satisfactorily with the state-of-the-art. Nonzero concentrations of CO are predicted in the external recirculation zone, which has not been achieved in previous modeling efforts. The validated solution was used as the basis to generate a CRN using the CFD-CRN method. The CFD-CRN method uses user-defined criteria to divide the CFD domain into a set of interconnected perfectly stirred reactors (PSRs) (i.e., a CRN). This CRN is then solved using detailed chemical kinetic mechanisms in the Kinetic Post-Processor (KPPSMOKE) solver. CRN size-independence studies are performed, and it is determined that 5000+ PSRs were needed to adequately capture pollutant formation in the complex recirculating flow field. Validation of CFD-CRN predictions of major species show similar accuracy to steady-state CFD simulation, with improvements over state-of-the-art CFD in CO profile predictions. Satisfactory agreement with previously published experimental NOx contour plots is also seen. The CFD-CRN is used to study NOx formation pathways in the swirling, turbulent environment of the S09c diffusion flame. As expected, NO seen to form primarily in the high-temperature internal recirculation zone (IRZ). The prompt pathway is predicted to be of greatest importance in this area. Significant NOx reburning is seen in the low temperature fuel air jets immediately adjacent to the IRZ. Overall, the prompt pathway is responsible for 77\\% of NOx leaving the system, with 12\\% due to thermal and 11\\% due to N2O intermediate.
Read moreIgnition Delay Time and Laminar Flame Speed Calculations for Natural Gas/Hydrogen Blends at Elevated Pressures
Applications of natural gas and hydrogen co-firing have received increased attention in the gas turbine market, which aims at higher flexibility due to concerns over the availability of fuels. While much work has been done in the development of a fuels database and corresponding chemical kinetics mechanism for natural gas mixtures, there are nonetheless few if any data for mixtures with high levels of hydrogen at conditions of interest to gas turbines. The focus of the present paper is on gas turbine engines with primary and secondary reaction zones as represented in the Alstom and Rolls Royce product portfolio. The present effort includes a parametric study, a gas turbine model study, and turbulent flame speed predictions. Using a highly optimized chemical kinetics mechanism, ignition delay times and laminar burning velocities were calculated for fuels from pure methane to pure hydrogen and with natural gas/hydrogen mixtures. A wide range of engine-relevant conditions were studied: pressures from 1 to 30 atm, flame temperatures from 1600 to 2200 K, primary combustor inlet temperature from 300 to 900 K, and secondary combustor inlet temperatures from 900 to 1400 K. Hydrogen addition was found to increase the reactivity of hydrocarbon fuels at all conditions by increasing the laminar flame speed and decreasing the ignition delay time. Predictions of turbulent flame speeds from the laminar flame speeds show that hydrogen addition affects the reactivity more when turbulence is considered. This combined effort of industrial and university partners brings together the know-how of applied, as well as experimental and theoretical disciplines.
Read moreLaminar Flame Speed Measurements and Modeling of Pure Alkanes and Alkane Blends at Elevated Pressures
Alkanes such as methane, ethane, and propane make up a large portion of most natural gas fuels. Natural gas is the primary fuel used in industrial gas turbines for power generation. Because of this, a fundamental understanding of the physical characteristics such as the laminar flame speed is necessary. Most importantly, this information is needed at elevated pressures to have the most relevance to the gas turbine industry for engine design. This study includes experiments performed at elevated pressures, up to 10 atm initial pressure, and investigates the fuels in a pure form as well as in binary blends. Flame speed modeling was done using an improved version of the kinetics model that the authors have been developing over the past few years. Modeling was performed for a wide range of conditions, including elevated pressures. Experimental conditions include pure methane, pure ethane, 80/20 mixtures of methane/ethane, and 60/40 mixtures of methane/ethane at initial pressures of 1 atm, 5 atm, and 10 atm. Also included in this study are pure propane and 80/20 methane/propane mixtures at 1 atm and 5 atm. The laminar flame speed and Markstein length measurements were obtained from a high-pressure flame speed facility using a constant-volume vessel. The facility includes optical access, a high-speed camera, a schlieren optical setup, a mixing manifold, and an isolated control room. The experiments were performed at room temperature, and the resulting images were analyzed using linear regression. The experimental and modeling results are presented and compared with previously published data. The data herein agree well with the published data. In addition, a hybrid correlation was created to perform a rigorous uncertainty analysis. This correlation gives the total uncertainty of the experiment with respect to the true value rather than reporting the standard deviation of a repeated experiment. Included in the data set are high-pressure results at conditions where in many cases for the single-component fuels few data existed and for the binary blends no data existed prior to this study. Overall, the agreement between the model and data is excellent.
Read moren-Butane: Ignition delay measurements at high pressure and detailed chemical kinetic simulations
Discrepancies between shock tube and rapid compression machine ignition at low temperatures and high pressures
Ignition and Oxidation of 50/50 Butane Isomer Blends
One of the alkanes found within gaseous fuel blends of interest to gas turbine applications is butane. There are two structural isomers of butane, normal butane and iso-butane, and the combustion characteristics of either isomer are not well known. Of particular interest to this work are mixtures of n-butane and iso-butane. A shock-tube experiment was performed to produce important ignition delay time data for these binary butane isomer mixtures which are not currently well studied, with emphasis on 50–50 blends of the two isomers. These data represent the most extensive shock-tube results to date for mixtures of n-butane and iso-butane. Ignition within the shock tube was determined from the sharp pressure rise measured at the endwall which is characteristic of such exothermic reactions. Both experimental and kinetics modeling results are presented for a wide range of stoichiometry (φ = 0.3–2.0), temperature (1056–1598 K), and pressure (1–21 atm). The results of this work serve as validation for the current chemical kinetics model. Correlations in the form of Arrhenius-type expressions are presented which agree well with both the experimental results and the kinetics modeling. The results of an ignition-delay-time sensitivity analysis are provided, and key reactions are identified. The data from this study are compared with the modeling results of 100% normal butane and 100% iso-butane. The 50/50 mixture of n-butane and iso-butane was shown to be more readily ignitable than 100% iso-butane but reacts slower than 100% n-butane only for the richer mixtures. There was little difference in ignition time between the lean mixtures.
Read moreA rapid compression machine study of the oxidation of propane in the negative temperature coefficient regime
Engine Performance Improvement by Controlling the Low Pressure Compressor Working Line
The new algorithm provides closed-loop control of the LP compressor working line in such a way as to maintain compressor stability and to provide increased power from the engine at the same firing temperature. This method is intended for the Trent 60, an aeroderivative engine designated for power generation and mechanical drive applications. The power benefit is achieved by operating at higher LPC pressure ratio and thereby increasing the inlet air flow and overall pressure ratio of the engine. Since the algorithm controls the working line, the threats to compressor stability related to the working line level are removed (including production scatter, deterioration, and fouling) and the required surge margin can be safely reduced, providing a significant benefit in engine performance. The paper presents comparatively the structure of the current and new concepts, the main features of the controller, and stresses the improved accuracy and reliability of new algorithms. The performance benefit is then assessed; the increase in power is about 3% at ISO, sea level conditions and varies with ambient temperature.
Read more