2 W single-longitudinal-mode Yb:YAG distributed-feedback waveguide laser.

We propose a new kind of distributed feedback (DFB) semiconductor laser based on the sampled Moire grating (SMG) integrated with a grating reflector (GR). Coupling coefficient along the laser cavity can be controlled, and $\pi $ phase shift ( $\pi $ -PS) can be introduced by SMG. The GR, which is a uniform sampled grating, can provide light reflection instead of high reflection (HR) facet coating. Thus, the front and rear facets are both coated with anti-reflection coatings (AR/AR) to avoid the influence of random grating phase at the HR facet. Therefore, more output power, better single longitudinal mode (SLM) operation, and higher wavelength precision can be simultaneously achieved, compared with traditional DFB lasers with AR/HR facet coatings. As an example, an 8-channel DFB laser array based on the proposed structure has been simulated. The proposed laser may benefit the applications requiring both high output power and wavelength precision, such as wavelength division multiplexing (WDM) transmission systems and gas sensors.

The effects of nonlinear gain on the single longitudinal mode are analyzed by means of multilongitudinal mode and multitransverse mode rate equations and compared with the linear gain calculations and experments. It is shown that further suppression of the third order nonlinear gain on nonlasing modes always serves to accelerate the process of the single longitudinal mode operation and that results obtained with long cavity length are entirely contrary to those where only linear gain is considered. The experiments also show that single longitudinal mode lasers with even larger output power can be realized with long cavity length; and, with further proper reduction of the stripe width, single mode (single frequency) operation can be realized. But the results obtained from both gain considerations indicate that single longitudinal mode operation will be facilitated if the active layer is not too thin and the end face reflectivity is increased.

We report on high-power operation of a fiber distributed-feedback (DFB) laser fabricated from Tm-doped photosensitive alumino-silicate fiber and in-band pumped by an Er/Yb fiber laser at 1565 nm. The fiber DFB laser yielded up to 875 mW of single-ended output at 1943 nm on two orthogonally polarized modes for 3.5 W of absorbed pump power. Further scaling of the DFB laser output power was achieved with the aid of a simple Tm-doped fiber amplifier stage spliced directly to the DFB fiber without the need of an optical isolator. The maximum output power from the DFB laser and fiber amplifier was >3 W for a combined absorbed pump power of 8.1 W. The influence of thermal loading, owing to quantum defect heating in the Tm-doped core, on the output power and longitudinal mode behavior is discussed, and the prospects for further improvement in performance are considered.

591-Mb/s noncoherent FSK 2/sup 23/-1 PRBS transmission experiments using two different commercial standard DFB (distributed feedback) lasers and a phase-tunable DFB laser have been carried out. The commercial DFB lasers are modulated with an AMI (alternated mark inversion) code and the phase-tunable DFB laser with a NRZ (nonreturn to zero) code. With an optical filter bandwidth of 2.7 GHz, receiver sensitivities (for a 10/sup -10/ BER) of -38 dBm for the phase-tunable DFB laser and -36 dBm for both standard DFB lasers are achieved. The influence of optical filter bandwidth and modulation index on the BER is also evaluated.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

In this paper, we present the theoretical investigation of index-coupled distributed feedback (DFB) laser with tilted single mode ridge waveguides. By tilting part of the ridge waveguide in various degrees, DFB laser with manifold effective grating periods can be realized. The structure is analyzed using couple mode theory in matrix form based on threshold analysis. Important parameters of DFB laser like resonant frequency and threshold gains are obtained by solving the eigen-equation. The results indicate not only that the lasing frequency is modulated by the waveguide titling angle, but also large Gain Margin (GM) can be achieved at the threshold condition which enhance the stable single mode operation in index-coupled DFB laser.

In this paper we present an experimental analysis of the effect of RF modulation injection current in DFB and FP lasers nearthe first period doubling bifurcation (PDB). By increasing the amplitude of the modulation frequency at the onset of PDB thefirst results of a virtual Hopf phenomenon like behavior has been observed in both types of lasers. We characterized thisobservation by increasing the amplitude of the current modulation where two peaks appear in the spectrum, approaching oneto the other until fmally merging the onset of period doubling bifurcation as predicted by theory. The same virtual Hopfbehavior was observed when we set the amplitude modulation at a fixed value and we sweep the frequency modulation at theonset of the PDB point.Keywords: Laser Diode, Nonlinear Dynamics, Period Doubling Bifurcations. 1. INTRODUCTION Nonlinear dynamics in diode lasers has been the subject of many theoretical and experimental investigations in the lastdecade as they show a rich variety of irregular behavior in their route to chaos1. A single frequency diode laser is commonlystudied by a rate equation model which describes the time evolution of the photon and carrier densities. In these equations,the inclusion of an additional degree of freedom as modulation of the injection current, external light injection or opticalfeedback is needed for nonlinear dynamics to appear2.To our knowledge, the nonlinear behavior in semiconductor diode lasers has been extensively studied by many authors usingdelayed optical feedback and strong current modulation. In the former, the observed route to chaos was through successivesubharmonic bifurcations or by quasi periodic route3'4. In the strong current modulation case the period sequence wastruncated by period tripling before the onset of chaos5'6.On the other hand, the onset of a period doubling bifurcation point in many physical systems brings to nonlinear phenomenasuch as: 1) small signal amplification, 2) shift and suppression of the bifurcation point and 3) the emergence of a closelyspaced set of peaks in the frequency response7.In semiconductor lasers the parametric amplification was observed by Harth and co-workers8'9 which was analyzed byWiesenfeld few years after'°. In the study developed by Wiesenfeld in ref. 10, semiconductor lasers were proposed as goodcandidate to study the rich variety of nonlinear phenomena near period doubling bifurcations. A recent study has shown thatthe effect of Langevin noise in period doubling semiconductor lasers has a virtual Hopf ur12 previously predicted byWiesenfeld'34 as a virtual Hopf phenomenon in systems undergoing a period doubling bifurcations in the presence ofexternal noise.In the present study we have experimentally investigated the nonlinear dynamics of diode lasers in the period doublingbifurcation point. We study the influence of the amplitude modulation in Distributed Feedback (DFB) lasers near perioddoubling bifurcations. In Fabry-Perot (FP) lasers we performed as well the same study as DFB lasers and the analysis of thefrequency modulation near period doubling bifurcation. So in section II we described the experimental procedure for theonset of the first period doubling bifurcation performed in commercial DFB and FP InGaAsP diode lasers at 1,3 tm emission

A statistical yield analysis is presented for gain- and index-coupled distributed feedback (DFB) laser structures, allowing a comparison of their single longitudinal mode (SLM) yield capabilities. For the yield calculations, the threshold gain difference and the longitudinal spatial hole burning (SHB) are taken into account. By comparing the experimental and theoretical yield of index-coupled DFB lasers, the significance of SHB for correct yield predictions is illustrated. For the purpose of comparison, yield calculations for various lambda /4-shifted DFB lasers (with low facet reflectivities) are presented. The most emphasis, however, is on partly gain-coupled DFB lasers. Estimations of practical gain coupling coefficient values for gain and for loss gratings are discussed. >

A great improvement in the high-speed characteristics for compressively strained multi-quantum-well (MQW) distributed-feedback (DFB) lasers with self-aligned constricted mesa structures is described. Negative wavelength detuning is an important factor in making possible the extraction of potential advantages for the compressively strained MQW DFB lasers. A 17-GHz bandwidth, which is the highest among the 1.5- mu m MQW DFB lasers, is demonstrated. A wavelength chirp width of 0.42 nm at 10 Gb/s is obtained due to a reduced linewidth enhancement factor that has a magnitude of less than 2. Nonlinear damping K factor in a DFB laser with 45-nm negative detuning has drastically decreased to 0.13 ns, about half of that for unstrained MQW lasers. This is mainly due to an enhanced differential gain as large as 6.9*10/sup -12/ m/sup 3//s. The estimated intrinsic maximum bandwidth is 68 GHz. >

Single longitudinal mode (SLM) distributed feedback (DFB) lasers with a linewidth lower than a few kHz find applications in many coherent detection systems. In this paper, we proposed and experimentally demonstrated a novel method to compress the linewidth of a SLM DFB laser by utilizing a dual-cavity feedback structure (DCFS). The DCFS first provides optical self-injection feedback to compress the laser linewidth, and then the two feedback lengths are carefully optimized to achieve SLM output via the Vernier principle and the suppression of modes overlapping between two cavities. The linewidthes of 1 MHz and 200 kHz were successfully compressed to ~2.7 and 1.5 kHz with a side mode suppression ratio of 38 and 45 dB, respectively. The stability of the DCFS output power can be controlled within ~0.21%. Our method provides a simple, effective, low cost way to achieve DFB linewidth compression, which will greatly improve the performance of coherent detection systems using DFB laser as sources.

We propose and experimentally demonstrate an all-pole-type cavity structure to force single longitudinal mode (SLM) operation in fiber lasers. The proposed structure is based on the modified version of the Smith predictor, which compensates delay in a closed-loop feedback system. This structure is applicable to arbitrary wavelengths and gain media, does not limit the tunability range of the laser, and does not require few centimeters long loops or Fabry-Pérot tunable filters to achieve SLM operation. Thus, the major drawbacks of the conventional SLM forcing mechanisms are alleviated. Therefore, this structure can be considered as a universal approach to SLM operation in fiber lasers. To exemplify this structure, an erbium-doped fiber ring laser in continuous-wave mode is implemented. The SLM operation is confirmed from the RF spectrum over a 10 GHz bandwidth, and the laser is tunable over 62 nm from 1512 to 1574 nm.

Summary form only given. For the reduction of the spectral bandwidth of optical parametric oscillators (OPO's) to values below 1 GHz the use of grazing-incidence (GI) grating has been demonstrated successfully. Even single longitudinal mode (SLM) operation is feasible. A GIOPO device uses the favourable intrinsic properties of nonlinear crystals and can be tuned over a wide spectral range. SLM operation and a large scan range have been demonstrated with a BaB/sub 2/O/sub 4/ GIOPO, where a signal range of 460-630 nm could be covered.

We report high slope efficiency and low noise characteristics in a distributed feedback (DFB) laser lasing at 1.3 /spl mu/m with narrow beam divergence by employment of a laterally tapered active stripe over the whole cavity. This tapered structure is designed to realize narrow beam divergence, low threshold current, and high longitudinal mode selectivity. The fabricated tapered-active-stripe DFB lasers demonstrated of 9.20/spl times/13.40 and a record slope efficiency, for a narrow beam DFB laser, of 0.59 mW/mA. The temperature characteristics from -10/spl deg/C to 85/spl deg/C shows high output power at high temperature, stable single longitudinal mode oscillation and stable far-field patterns. Furthermore, for the first time ever, a low relative intensity noise characteristic of under -155 dB/Hz has been realized when butt-coupling into a single-mode fiber.

Enhancement of asymmetry in light output from front/rear facets in resonance-shifted DFB-LDs

The dynamic linewidth enhancement factor, (alpha) , and damping rate, (Gamma) , for distributed feedback (DFB) lasers are obtained at various bias levels by measuring the frequency modulation and amplitude modulation indices of the lasers simultaneously. The (alpha) -value of a DFB lasers is generally reduced with increasing output power except at low bias, and the (Gamma) -value typically increases with output power. The measured results show that ninety percent of the 1.3-micrometers capped-mesa buried heterostructure DFB lasers have (alpha) -values in the range 4 to 7 and (Gamma) -values below 4 X 10<SUP>10</SUP> s<SUP>-1</SUP>. The 1.3-micrometers lasers have smaller damping rates than the 1.5- micrometers lasers of the same DFB laser structure. Compared with buried heterostructure DFB lasers, multiquantum well (MQW) DFB lasers exhibit a much smaller (alpha) -value and a larger damping rate. For both unstrained and strained 1.5-micrometers MQW-DFB lasers, (alpha) -values as low as 1.5 can be easily realized for these lasers at high output power (&gt;= 10 mW).

An analytic expression for the linewidth of distributed-feedback (DFB) lasers is derived. Local fluctuations in carrier density are shown to provide a significant contribution to laser linewidth in the presence of spatial holeburning. In a single-electrode DFB laser the effect can be avoided by careful optimization of the kl-product, but for a multielectrode DFB laser the linewidth can also be reduced by adjusting the injected current profile to compensate for spatial holeburning. Numerical results for a three-electrode lambda /4-shifted DFB laser are presented.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>