A Improved Decoding Algorithm for Low-Density Parity-Check Codes

Low-density parity-check (LDPC) codes are predominantly used in many energy scavenging devices, data centres, and communication devices. In this work, the authors propose a high-throughput parallel bit-flipping (BF) decoder using multithreshold BF algorithm. The decoder is endowed with features including low interconnect complexity, simpler computations, and high throughput. The decoder has been synthesised in 65 nm technology for (273, 191) and (1023, 781) finite-geometry LDPC (FG-LDPC) codes. These decoders require an area of 0 . 1 and 0 . 45 mm 2 , and they achieve an average throughput of 147 . 57 and 268 . 5 Gbps and energy efficiency of 0 . 92 and 0 . 91 pJ/bit for (273, 191) and (1023, 781) FG-LDPC codes, respectively. Compared to the state-of-the-art design, the proposed designs offer 4 . 5 times higher normalised throughput.

Recently, in multi-way relay systems employing physical-layer network coding (PNC), channel condition-based pair selection for pairwise information exchange has drawn increased attention as it provides improved performance over the alternative approaches such as round-robin scheduling of node pairs. With pairwise information exchange, there is additional time diversity available due to transmission of the same coded information block of most of the nodes twice in two adjacent time slots. This additional time diversity can be exploited to further enhance the system performance by means of joint channel decoding-network coding. To this end, a joint belief propagation (BP)-based channel decoding-network coding algorithm was proposed by us in [9] for the relay node of low density parity check (LDPC)-coded multi-way relay systems. Even though the algorithm of [9] offers much superior performance over separate channel decoding, it is highly computational expensive and may not be suitable for applications in wireless sensor networks. Alternatively, bit-flipping (BF)-based LDPC decoding can be adopted at much lower computational complexity. In this paper, we develop a low complexity joint bit-flipping (BF)-based channel decoding and network coding algorithm for LDPC-based multi-way relay systems. The BER performance of the proposed algorithm is investigated using computer simulation for two commonly used LDPC codes. The simulation results demonstrate that superior BER performance can be achieved using the proposed joint decoding algorithm over separate and independent bit-flipping-based LDPC channel decoding at the relay. The simulation results also verify that our proposed algorithm is capable of harnessing the aforesaid additional time diversity available. Though the performance of the proposed joint decoding algorithm is inferior to the BP-based algorithm of [9], due to its low computationally complexity, this algorithm may be appealing for applications in relay nodes with low computational capabilities and memory constraints.

Day by day the internet traffic is increasing rapidly. Challenges to improve these internet traffic requirements leads to evolution of 5G NR LDPC (New Radio Low Density Parity Check) codes which provides high coding gain and energy efficiency. BER Vs Eb/No dB curve defines the energy efficiency and coding gain of the any error correcting codes. LDPC codes which are adopted by 5G Standard are called 5G NR LDPC codes.In the design of the decoder,Message Passing Approach reduces the decoding complexity due to the sparsity of the parity check matrix. An efficient decoding algorithm is the key to the successful code. In this paper an iterative minsum approximation message passing decoding algorithm has been implemented for both BG1 and BG2. Results show that the coding gain can be improved up to 9dB.

A novel self-normalized weighted bit-flipping (SNWBF) decoding algorithm for low-density parity-check (LDPC) codes is proposed. Compared to the best known weighted bit-flipping decoding, the SNWBF algorithm converges significantly faster but with little performance penalty. For decoding of LDPC codes, the proposed SNWBF algorithm considers not only the reliability of the neighboring check nodes, but also the reliability of each variable node. Compared to the IMWBF algorithm, the proposed algorithm does not require multiplicative normalization and performs even better.

In this paper a new decoding algorithm for low density parity check (LDPC) codes based on bit flipping (BF) is proposed. In the proposed algorithm, the BF criterion benefits the data correlation between the decoded and received signal in current and previous stages. The proposed algorithm also degrades the decoding probability of one code word to another one in the same codebook. Simulation results confirm our theoretical formulation and show a good enhancement in code error rate and bit error rate of the proposed decoding algorithm compared to the conventional ones.

We propose a novel concatenated coding scheme combined Low Density Parity Check(LDPC) code and vertical Bell Labs layered space-time (VBLAST) code to improve the bit error rate (BER) performance for Free-space optical (FSO) communication links with On Off Keying(OOK) modulation. In the scheme, π-rotation encoding and belief-propagation (BP) decoding algorithm are employed in LDPC code, and minimum mean-square error (MMSE) soft-decision decoding algorithm is used for VBLAST code. Moreover, a joint iterative detection and decoding algorithm of VBLAST code and LDPC code is used to improve the overall link performance. At last, the BER of the proposed scheme over lognormal atmospheric turbulent fading channels is analyzed by using Monte Carlo method. The result shows that the BER of the proposed concatenated coding scheme is much improved than that only use VBLAST code scheme.

Low Density Parity Check (LDPC) codes are Shannon-Limit approaching codes. Shannon stated the theoretical bounds for digital data transmission in a given channel capacity with error correction coding. Spread Spectrum also called as CDMA (Code Division Multiple Access) is an efficient way of radio wave communication deployed in commercial broadcasts, ham radios, military communications, police radios, etc. CDMA is a means of signal transmission in which the signal frequency is spread over a very wide bandwidth. Spreading of data is achieved prior to transmission with the help of an independent code called ‘Pseudo Noise Code’ (PN sequences), which is subsequently used in the receiver end to de-spread the signal received in order to recover the signal data. PN sequences based on prime numbers like Legendre & Weil sequences are used in the present work. An impressive part of LDPC lies in its decoding algorithm. Sum-Product Algorithm (SPA) decoding offers the best error performance amongst all the types of decoding techniques of LDPC codes and thus applied here. This paper demonstrates an idea of introducing LDPC codes along with DS-Spread Spectrum technique using Legendre & Weil sequences. In the present work, the encoding and decoding algorithms are applied after spreading of the signal. SPA decoding technique is successfully employed and simulated results are plotted taking an example design to illustrate the concepts discussed above.

In this paper we propose an innovative channel coding scheme called 'Accumulate Repeat Accumulate codes' (ARA). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes, thus belief propagation can be used for iterative decoding of ARA codes on a graph. The structure of encoder for this class can be viewed as precoded Repeat Accumulate (RA) code or as precoded Irregular Repeat Accumulate (IRA) code, where simply an accumulator is chosen as a precoder. Thus ARA codes have simple, and very fast encoder structure when they representing LDPC codes. Based on density evolution for LDPC codes through some examples for ARA codes, we show that for maximum variable node degree 5 a minimum bit SNR as low as 0.08 dB from channel capacity for rate 1/2 can be achieved as the block size goes to infinity. Thus based on fixed low maximum variable node degree, its threshold outperforms not only the RA and IRA codes but also the best known LDPC codes with the dame maximum node degree. Furthermore by puncturing the accumulators any desired high rate codes close to code rate 1 can be obtained with thresholds that stay close to the channel capacity thresholds uniformly. Iterative decoding simulation results are provided. The ARA codes also have projected graph or protograph representation that allows for high speed decoder implementation.

Turbo codes are attractive compared with Low Density Parity Check (LDPC) codes for Forward Error Correction (FEC) applications mainly due to their superior performance, especially at low Signal-to-Noise Ratio (SNR) such as are common in Powerline channels. For example, IEEE 1901-FFT PHY used the Turbo coding scheme defined in the HomePlug AV standards. However, patent fees are usually required for each turbo-code enabled manufactured device. The objective of this paper is to examine whether unlicensed LDPC codes, with optimized choices of block lengths, could be a viable alternative for future Powerline Communications (PLC) applications. The paper shows that the performance of the LDPC codes can approximate that of the Turbo codes with higher block lengths, on channels with typical and realistic PLC characteristics. The paper also shows that the additional complexity associated with this increase in block length can be mitigated by the use of Quasi-Cyclic LDPC (QC-LDPC) codes.

Low Density Parity Check (LDPC) codes have capacity-approaching performance over several channels of interest. In practice, for good block-error rate performance, the girth of the Tanner graph of an LDPC code needs to be as high as possible. In theory, to show that block-error rate approaches zero for increasing block-lengths, the girth of the Tanner graph sequence needs to tend to infinity with block-length. To meet these requirements, we construct sequences of large-girth irregular LDPC codes for a given degree-distribution pair (DDP) by applying a general node splitting algorithm on large girth graphs. The obtained Tanner graph meets the required DDP up to a suitable approximation. By optimizing the node-splitting method and using suitable large-girth graphs, we show code constructions with smaller block length for the same girth, when compared to previous constructions. Similar gains in block length are observed in the construction of sequences of large-girth protograph LDPC codes. Simulations, over a binary erasure channel, confirm the gains in block-error rate obtained by the large girth construction.

Big data storage demands larger cluster. The increasing size of the cluster may lead to failures of larger number of nodes. To provide reliable big data storage, replications are not cost-effective and does not provide a robust solution to prevent data loss. Traditional erasure codes applied in the RAID system such as Reed-Solomon (R-S) based solutions have limitations in providing high reliability. This is because higher reliability requires erasure codes with larger size. The computational cost of the R-S codes increase quadratically with the number of failures the R-S codes can tolerate for the same redundancy rate. It has been shown that Low Density Parity Check (LDPC) codes have lower computational cost and repair network traffic compared with R-S based solutions. Unfortunately, there does not exist a construction method for LDPC codes with larger size to control the computational cost and repair traffic. In this paper, a novel method is proposed to construct a family of LDPC codes - expanCodes with expandable sizes. The proposed expanCodes allows the encoding and decoding complexity remain unchanged with the increase of the size of the LDPC codes. As a result, increased reliability can be achieved without additional computation and repair traffic. The proposed expanCodes is integrated with the Hadoop system. Simulations show that more than 29% decrease in terms of encoding and decoding latency compared with R-S based solutions.

A novel bit-flipping (BF) algorithm with low complexity for high-throughput decoding of low-density parity-check (LDPC) codes is presented. At each iteration, a novel threshold pattern is used to determine the code bits whether to be flipped or not, and the flipping error probability is effectively decreased. Compared with the weighted BF algorithm and its modifications, the modified BF algorithm has significantly lower complexity and decoding time. Through simulations the proposed BF algorithm is shown to achieve excellent performance and fast convergence speed while maintaining significantly low complexity thus facilitating high-throughput decoding.

Key extraction based on wireless channel-characteristics (Physical-Layer Key) is the new technology to ensure communication security. To solve the problem that the channel characteristics are not completely consistent in the process of key generation, low density parity check (LDPC) codes was proposed. But due to the process of the traditional decoding algorithm of LDPC codes, the computation of check nodes renew is too high and the efficiency of key reconciliation is too low. To overcome this problem, we propose the modified decoding algorithm of LDPC codes that combine traditional decoding algorithm and Offset-base decoding algorithm. This algorithm can reduce the computational complexity efficiently, and improve the efficiency of key reconciliation. Finally, the simulation results demonstrate that, the BER and success ratio of the key reconciliation is improving.

Scheduling strategy is considered an important aspect of belief-propagation (BP) decoding of low-density parity-check (LDPC) codes because it affects the decoder's convergence rate, decoding complexity and error-correction performance. In this paper, we propose two new scheduling strategies for the BP decoding of non-binary LDPC (NB-LDPC) codes. Both the strategies are devised based on the concept of check node reliability and employ a heuristically defined threshold which can adapt to the communication channel variations. As the scheduling strategies only update a subset of the check nodes in each iteration, they result in reduced iteration cost. Furthermore, since the BP performs suboptimally for finite-length LDPC codes, especially for short-length LDPC codes, by enhancing the message propagation over the Tanner Graphs of short-length NB-LDPC codes, the new scheduling strategies can even improve the error-correction performances of BP decoding. Simulation results demonstrate that the new scheduling strategies provide good performance/complexity tradeoffs.

Effect of channel mismatch on decoding performance of low density parity check (LDPC) codes over binary symmetric channel (BSC) under sum-product algorithm (SPA) is analyzed in this paper. Density evolution is employed in theoretical analysis to get optimal initial value for SPA. Based on the results, a modified SPA algorithm is proposed. When decoding using this modified SPA algorithm, no channel information is needed at the decoder side. This will be of significant value for time-varying channels. Theoretical claims from density evolution are confirmed by extensive simulations. Our simulations show that by fixing the initial value for all channel conditions, decoding performance can be improved. One channel state estimation algorithm is proposed in this paper based on the error detection ability of LDPC codes. Maximum number of iterations taken when decoding a LDPC code can be dynamically adjusted according to the estimated channel state. Further performance improvements can be achieved by using the dynamic iteration number adjusting scheme together with the modified sum-product algorithm.