A Novel Threat Modeling and Attack Analysis for IoT Applications

As location-aware IoT (Internet of Things) devices intend to spread across almost every application, IoT devices are going to require different GNSS (Global Navigation Satellite System) receiver design requirements. To deliver on IoT opportunities, system architects and designers need to look carefully at every aspect of system design and architecture to be able to enable the full potential of the IoT era. IoT devices are equipped with different connectivity sensors that can provide a reliable integrated location-awareness solution. IoT devices are mainly relying on GNSS chip to deliver a service when no other RF signal is available. Hence, GNSS chip is expected to maintain a robust and reliable performance even in harsh environment. The harsh environment includes multipath environment, NLOS (Non-Line of Sight) GNSS signal reception, weak GNSS signal power reception, superimposed motion (e.g., arm swing, floating platform fluctuation …etc.), operation under freezing temperature, and interference. The targeted low-cost system design along with the expected harsh operational environment derived us to face exceptional GNSS signal reception condition. This paper discusses lessons learned, and challenges faced signal acquisition, reacquisition, and tracking for several IoT applications. Different operational modes are also explored to accommodate various use cases scenarios for several IoT applications. These different power consumption operational modes allow the GNSS chip to achieve an Ultra-low power consumption which indeed required for IoT applications. This paper provides an overview about the addressed GNSS chip fabricated in a 28nm FD-SOI process. We demonstrate a system performance and power consumption comparison of this chip along with other state-of-the-art GNSS chip. We compare the positioning performance for this device alongside another state-of-the-art GNSS modules and Novatel’s tightly coupled GNSS/INS (Inertial Navigation System) reference solution at numerous scenarios ranging from walking, running, and driving at several sites under different environment.

With the advancement of 5G mobile telecommunication, various IoT (Internet of Things) devices communicate massive amounts of data by being connected to wireless networks. Since this wireless communication is vulnerable to hackers via data leakage during communication, the transmitted data should be encrypted through block ciphers to protect the data during communication. In addition, in order to encrypt the massive amounts of data securely, it is essential to apply one of secure mode of operation. Among them, CTR (CounTeR) mode is the most widely used in industrial applications. However, these IoT devices have limited resources of computing and memory compared to typical computers, so that it is challenging to process cryptographic algorithms that have computation-intensive tasks in IoT devices at high speed. Thus, it is required that cryptographic algorithms are optimized in IoT devices. In other words, optimizing cryptographic operations on these IoT devices is not only basic but also an essential effort in order to build secure IoT-based service systems. For efficient encryption on IoT devices, even though several ARX (Add-Rotate-XOR)-based ciphers have been proposed, it still necessary to improve the performance of encryption for smooth and secure IoT services. In this article, we propose the first parallel implementations of CTR mode of ARX-based ciphers: LEA (Lightweight Encryption Algorithm), HIGHT (high security and light weight), and revised CHAM on the ARMv8 platform, a popular microcontroller in various IoT applications. For the parallel implementation, we propose an efficient data parallelism technique and register scheduling, which maximizes the usage of vector registers. Through proposed techniques, we process the maximum amount of encryption simultaneously by utilizing all vector registers. Namely, in the case of HIGHT and revised CHAM-64/128 (resp. LEA, revised CHAM-128/128, and CHAM-128/256), we can execute 48 (resp. 24) encryptions simultaneously. In addition, we optimize the process of CTR mode by pre-computing and using the intermediate value of some initial rounds by utilizing the property that the nonce part of CTR mode input is fixed during encryptions. Through the pre-computation table, CTR mode is optimized up until round 4 in LEA, round 5 in HIGHT, and round 7 in revised CHAM. With the proposed parallel processing technique, our software provides 3.09%, 5.26%, and 9.52% of improved performance in LEA, HIGHT, and revised CHAM-64/128, respectively, compared to the existing parallel works in ARM-based MCU. Furthermore, with the proposed CTR mode optimization technique, our software provides the most improved performance with 8.76%, 8.62%, and 15.87% in LEA-CTR, HIGHT-CTR, and revised CHAM-CTR, respectively. This work is the fastest implementation of CTR mode on ARMv8 architecture to the best of our knowledge.

The Internet of Things (IoT) has had a considerable influence on our daily lives by enabling enhanced connection of devices, systems, and services that extends beyond machine-to-machine interactions and encompasses a wide range of protocols, domains, and applications. However, despite privacy concerns shown by IoT users, little has been done to reduce and protect individual information exposure. It is extremely difficult to mitigate IoT devices from reidentification threats which is why it is still a major challenge for IoT users to securely protect their information. The trust controls how we regulate privacy in our IoT platforms in the same way that it governs personal relationships. As IoT devices become increasingly linked, more data is shared across individuals, businesses, governments, and ecosystems. Technologies, sensors, machines, data, and cloud connections all rely largely on trust relationships that have been formed. With the rapid growth of additional types of IoT devices that are being introduced, it, therefore, expands privacy concerns and is difficult to develop trust with an IoT system or device without the option to regulate information privacy settings. Privacy has always been a barrier for many devices as they race for the early adoption of IoT technologies. Several Internet of Things devices or systems will continue to pose privacy threats. As a result, the main objective of this study was to examine the individual understanding of privacy and to promote information privacy protection awareness not only to IoT users but also to organizations that use IoT devices or platforms to run their day-to-day business operations. Furthermore, the objective extends to compare user knowledge and concerns about IoT privacy, as well as to identify any common attitudes and variances. However, in terms of enhancing individuals’ knowledge, an artifact was developed to educate and enhance information privacy awareness among IoT users. A pre- and postquestionnaire was generated to test and validate user knowledge regarding information privacy protection in IoT. The study was conducted using a quantitative research method. Findings indicate that IoT users’ awareness of information privacy protection turned out to be average, suggesting a need for education and awareness. Several participants stated that information privacy protection awareness is required within the community to educate, raise awareness, eliminate human error, and enable individuals to be conscious of their privacy when surfing the Internet.

The Internet of Things (IoT) devices is able to communicate with another IoT devices in heterogeneous environments. They are also able to create a network by their own using wireless capabilities without a centralized approach. This network is called wireless mobile ad hoc network (MANET). The MANET facilitate IoT devices to communicate with each other in an infrastructure less network of the Internet of Things environment. The IoT devices can dynamically join, create connection and exchange information among them. The role of cloud in this framework is to store and process the data by IoT devices. The communication Security has been raised as one of the most critical issues of cloud computing where resolving such an issue would result in a constant growth in the use and popularity of cloud. Our purpose of this study is to create a framework for providing the communication in an integrated framework of Cloud and MANET among IoT devices. Our main contribution links a new study that integrates cloud computing to the MANET and provides communication to the internet of things. This study can be used in the framework of the Internet of Things in future.

Seeing is not always believing: Insights on IoT manufacturing from firmware composition analysis and vendor survey

With the advancement in science and technology, the demand for electronic Internet of Things (IoT) devices has increased to store and process digital data. With the advancement in IoT technology, we are more reliant on IoT devices to perform our regular tasks. IoT Forensics deals with the investigation of IoT devices such as smartphones, tablets, smart watches, or any device which is connected to the Internet. The data on these devices can still be retrieved via IoT forensics even if they are destroyed, resold, or misplaced. Before discarding any IoT device, we must consider how to secure the data stored on them. We are then going to discuss the several types of personal data that could be retrieved from discarded IoT devices. Finally, we are going to discuss the protection measures for the safe disposal of IoT devices.

Privacy preserving Internet of Things: From privacy techniques to a blueprint architecture and efficient implementation

In the modern security-conscious world, Deep Packet Inspection (DPI) proxies are increasingly often used on industrial and enterprise networks to perform TLS unwrapping on all outbound connections. However, enabling TLS unwrapping requires local devices to have the DPI proxy Certificate Authority certificates installed. While for conventional computing devices this is addressed via enterprise management, it's a difficult problem for Internet of Things (IoT) devices which are generally not under enterprise management, and may not even be capable of it due to their resource-constrained nature. Thus, for typical IoT devices, being installed on a network with DPI requires either manual device configuration or custom DPI proxy configuration, both of which solutions have significant shortcomings. This poses a serious challenge to the deployment of IoT devices on DPI-enabled intranets. The authors propose a solution to this problem: a method of installing on IoT devices the CA certificates for DPI proxy CAs, as well as other security configuration (security bootstrapping). The proposed solution respects the DPI policies, while allowing the commissioning of IoT and IIoT devices without the need for additional manual configuration either at device scope or at network scope. This is accomplished by performing the bootstrap operation over unsecured connection, and downloading certificates using TLS validation at application level. The resulting solution is light-weight and secure, yet does not require validation of the DPI proxy's CA certificates in order to perform the security bootstrapping, thus avoiding the chicken-and-egg problem inherent in using TLS on DPI-enabled intranets.

Elderly population in the Asian countries is increasing at a very fast rate. Lack of healthcare resources and infrastructure in many countries makes the task of provding proper healthcare difficult. Internet of things (IoT) in healthcare can address the problem effectively. Patient care is possible at home using IoT devices. IoT devices are used to collect different types of data. Various algorithms may be used to analyse data. IoT devices are connected to the internet and all the data of the patients with various health reports are available online and hence security issues arise. IoT sensors, IoT communication technologies, IoT gadgets, components of IoT, IoT layers, cloud and fog computing, benefits of IoT, IoT-based algorithms, IoT security issues, and IoT challenges are discussed in the chapter. Nowadays global epidemic COVID19 has demolished the economy and health services of all the countries worldwide. Usefulness of IoT in COVID19-related issues is explained here.

Delivering information from Internet of Things (IoT) devices to a cloud server possesses several security issues, e.g. information eavesdropping, modification, and theft. Therefore, communication between IoT devices and the cloud server should be protected by encryption methods. However, there are few encryption techniques options that are suitable for the need for lightweight communication as demanded by the IoT devices. Due to these circumstances, the NSA launched an encryption algorithm for IoT named Simon and Speck, which are maximally efficient while still providing the advertised level of security, as determined by the key size. This study aims to test and compare the Simon-Speck and AES encryption algorithms and their effect on networking performance on IoT devices. The parameters in this test are delay, throughput, the efficiency of memory usage from the encryption algorithm, and the value of the avalanche effect. Experimental results show that the Speck algorithm outperforms the Simon and the AES algorithms in terms of communication delay and memory usage. Regarding the avalanche effect values, the Simon algorithm possesses the highest avalanche effect value on average against the Speck and the AES algorithms.

Due to the rapid growth of the Internet of Things (IoT), researchers have demonstrated various IoT solutions, which are used to interconnect a wide range of IoT devices through the Internet. However, IoT stumbled into vertical silos; the available solutions provide specific IoT infrastructure, devices, protocols, data formats and models. This diversity and heterogeneity lead to interoperability issues. Heterogeneity happens at all IoT layers, especially at the application layer; devices often adopt mutually incompatible application-layer communication protocols to connect devices to IoT services. Furthermore, in order to integrate semantics to raw data, each system uses its one domain-specific ontology to make data more understandable and interpretable by adding semantic annotations. Working in isolation reduces the interoperability among IoT devices and systems, things across domains need to internetwork and collaborate to provide high level IoT services. Therefore, to alleviate the problem of both communication protocol interoperability and semantic interoperability across vertical silos of systems at the application layer, this paper proposes a semantic gateway (SGIoT) that acts as a bridge between heterogeneous sink nodes at the physical level and IoT services. SGIoT enables interconnectivity between communication protocols such as CoAP and MQTT regardless of their communication model, meanwhile it enables semantics integration throu gh cross-domain ontology (CDOnto) for semantic annotation, in order to provide interpretation of messages among IoT applications across domains. Our approach focuses on modularity and extensibility.

SummaryRecently, the deployment of novel smart network concepts, such as the Internet of things (IoT) or machine‐to‐machine communication, has gained more attention owing to its role in providing communication among various smart devices. The IoT involves a set of IoT devices (IoTDs) such as actuators and sensors that communicate with IoT applications via IoT gateways without human intervention. The IoTDs have different traffic types with various delay requirements, and we can classify them into two main groups: critical and massive IoTDs. The fundamental promising technology in the IoT is the advanced long‐term evolution (LTE‐A). In the future, the number of IoTDs attempting to access an LTE‐A network in a short period will increase rapidly and, thus, significantly reduce the performance of the LTE‐A network and affect the QoS required by variant IoT traffic. Therefore, efficient resource allocation is required.In this paper, we propose a priority‐based allocation scheme for multiclass service in IoT to efficiently share resources between critical and massive IoTD traffic based on their specific characteristics while protecting the critical IoTDs, which have a higher priority over the massive IoTDs. The performance of the proposed scheme is analyzed using the Geo/G/1 queuing system focusing on QoS guarantees and resource utilization of both critical and massive IoTDs. The distribution of service time of the proposed system is determined and, thus, the average waiting and service times are derived. The results indicate that the performance of the massive IoTDs depends on the data traffic characteristics of the critical IoTDs. Furthermore, the results emphasize the importance of the system delay analysis and demonstrate its effects on IoT configurations.

The number of Internet of Things (IoT) devices has increased recently and will increase further in the future. IoT devices are vulnerable, so vendors update and distribute firmware. At the time of firmware distribution, a huge number of IoT devices may connect to the firmware server and excessive network traffic may occur. Consequently, a method using a peer-to-peer file sharing system and a blockchain has been proposed. One study proposed an update scheme considering incentives for distributors to help with updating. However, this method requires the IoT devices, which have limited processing power, to decrypt encrypted files, and the distribution nodes to pay the transaction cost. This paper proposes a firmware distribution method that provides incentives for distributors to help with distribution to reduce the gas costs, using a smart contract and access control based on update records. The additional computations performed by IoT devices and distributors key management were reduced compared to those in previous studies by using access control instead of encryption. Further, the proposed approach was implemented and evaluated using a Raspberry Pi and laptop. The evaluation demonstrated that the gas cost per update was successfully lowered compared to the costs in previous studies.

The development and use of Internet of Things (IoT) devices have grown significantly in recent years. Advanced IoT device characteristics are mainly to blame for the wide range of applications that may now be achieved with IoT devices. Corporations have begun to embrace the IoT concept. Identifying true and suitable devices, security faults that might be used for bad reasons, and administration of such devices are only a few of the issues that IoT, a new concept in technological progress, provides. In some ways, IoT device traffic differs from regular device traffic. Devices with particular features can be classified into categories, irrespective of their function or performance. Ever-changing and complex environments, like a smart home, demand this classification scheme. A total of 41 IoT devices were employed in this investigation. To build a multiclass classification model, IoT devices contributed 13 network traffic parameters. To further preprocess the raw data received, preprocessing techniques like Normalization and Dataset Scaling were utilized. Feature engineering techniques can extract features from the text data. A total of 117,423 feature vectors are contained in the dataset after stratification, which are used to further improve the classification model. In this study, a variety of performance indicators were employed to show the performance of the logiboosted algorithms. Logi-XGB scored 80.2% accuracy following application of the logit-boosted algorithms to the dataset for classification, whereas Logi-GBC achieved 77.8% accuracy. Meanwhile, Logi-ABC attained 80.7% accuracy. Logi-CBC, on the other hand, received the highest Accuracy score of 85.6%. The accuracy of Logi-LGBM and Logi-HGBC was the same at 81.37% each. Our suggested Logi-CBC showed the highest accuracy on the dataset when compared to existing Logit-Boosted Algorithms used in earlier studies.

With the growth of wireless network technology-based devices, identifying the communication behaviour of wireless connectivity enabled devices, e.g. Internet of Things (IoT) devices, is one of the vital aspects, in managing and securing IoT networks. Initially, devices use frames to connect to the access point on the local area network and then, use packets of typical communication protocols through the access point to communicate over the Internet. Toward this goal, network packet and IEEE 802.11 media access control (MAC) frame analysis may assist in managing IoT networks efficiently, and allow investigation of inclusive behaviour of IoT devices. This paper presents network traffic traces data of D-Link IoT devices from packet and frame levels. Data collection experiment has been conducted in the Network Systems and Signal Processing (NSSP) laboratory at Universiti Brunei Darussalam (UBD). All the required devices, such as IoT devices, workstation, smartphone, laptop, USB Ethernet adapter, and USB WiFi adapter, have been configured accordingly, to capture and store network traffic traces of the 14 IoT devices in the laboratory. These IoT devices were from the same manufacture (D-Link) with different types, such as camera, home-hub, door-window sensor, and smart-plug.