A Rapid Single-Phase Blackout Detection Algorithm Based on Clarke–Park Transformations

Aim: This study sought to evaluate the effects of different irrigation solutions and sterilization processes on the surface properties of ProTaper Next (PTN; Dentsply-Maillefer, Ballaigues, Switzerland) and TruNatomy (TN; Dentsply Sirona, Ballaigues, Switzerland) nickel-titanium rotary files. Methodology: 30 ProTaper Next and 30 TruNatomy files were used. Both types of files were divided into five groups. The files in three groups were dipped into 5.25% NaOCI (CanalPro, Coltene/Whaledent, Altstätten, Switzerland), BioAKT (New Tech Solutions s.r.l., Brescia, Italy), and 18% etidronic acid (Dual Rinse HEDP, Medcem, Weinfelden, Switzerland), respectively, for 5 minutes, while the files in the fourth group were exposed to five autoclave cycles. The files in the fifth (control) group did not receive any treatment. Scans were performed from five different points using an atomic force microscope (AFM). The assumption of the conformity of the quantitative variables to a normal distribution was evaluated using the Kolmogorov-Smirnov test. A one-way analysis of variance was used to compare the quantitative measures between more than two independent groups, while the post-hoc least significant difference test was used for the pairwise comparisons (p˂0.05). Results: AFM images of the PTN and TN files in all the groups revealed surface irregularities. The root mean square (RMS) and depth values of the files dipped in NaOCI, BioAKT, and Etidronic acid were statistically higher than those of the control group (p<0.05). Moreover, the RMS and depth values were statistically higher in the files that had been subjected to five autoclave cycles when compared with the control group (p<0.05). The RMS values and depth values among the groups were found to be compatible. Conclusion: All the applications increased the surface roughness of the PTN and TN files. The Etidronic acid and sterilization applications were found to increase the RMS and depth values ​​the most when compared with the control group. How to cite this article: Öztekin F, Elmalı E. The effect of irrigation solutions and sterilization process on the surface properties of ProTaper Next and TruNatomy rotary files: An atomic force microscopy study. Int Dent Res 2022;12(2):39-46. https://doi.org/10.5577/intdentres.2022.vol12.no2.1 Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

Measuring a value by definition seems to be the best solution for getting the most precise results. In this paper, it is shown that by changing the general definition of root mean square (RMS) and average value of a periodic signal, their measurement can be improved. When measuring RMS with asynchronous sampling, it was observed that results were scattered around two values, and it was found that the main cause for this was initial sampling time. Redefining the RMS value has been proposed in order to increase the efficiency of the asynchronous method. After comparing the results based on general and proposed definition for RMS value, it was observed that there was significantly less scattering of results and higher accuracy. The simulation proved that the application of the proposed definition of RMS gives more accurate and precise results than the general definition for analog to digital (AD) converters with both lower and higher resolution.

Inhomogeneities in muscle activation reveal motor unit recruitment

Several exercise methods, such as the Shaker exercise, tongue press exercise, chin tuck against resistance (CTAR) exercise, and submandibular push exercise, have been introduced to strengthen the muscles involved in swallowing. In this study, we compared the effectiveness of the CTAR, submandibular push, and Shaker exercises for the induction of selective supra- and infrahyoid muscle contractions using surface electromyography (EMG). This study is a prospective non-randomized controlled study. Twenty-five healthy subjects and 20 patients experiencing swallowing difficulty were enrolled. During the three different types of exercises, the root mean square (RMS) values of the sternocleidomastoid (SCM), suprahyoid (anterior belly of the digastric and mylohyoid muscles), and infrahyoid (sternothyroid and thyrohyoid muscles) muscles were analyzed using surface EMG. Differences in the activity of swallowing muscles among the three different exercises were analyzed using one-way repeated measured analysis of variance. In terms of both the maximum and mean RMS values of the suprahyoid muscle, the submandibular push exercise showed a larger RMS value than the CTAR and Shaker exercises in healthy subjects (p < 0.05). In terms of both the maximum and mean RMS values of the suprahyoid muscle, the Shaker exercise and submandibular push exercise showed a larger RMS value than the CTAR exercise in patients with swallowing difficulty (p < 0.05). The submandibular push exercise may be effective as a swallowing muscle exercise owing to its superiority in inducing selective contractions of the supra- and infrahyoid muscles. The CTAR and Shaker exercises are also effective in this regard.

In recent years, real-time global ionospheric map (RT-GIM) products have been actively developed by the international global navigation satellite system (GNSS) service (IGS) and its ionosphere associate analysis centers (IAACs) along with the increase of RT-GNSS multi-frequency and multi-constellation observations. In this study, the accuracy and consistency of three RT-GIM products from the Chinese Academy of Sciences (CAS), Wuhan University (WHU), and IGS are evaluated and analyzed utilizing three validation methods, namely, comparison with JASON-3 vertical total electron content (VTEC), the difference of slant total electron content (dSTEC), and IGS combined final GIM (IGSG) data. The test period was from 1 January 2019 to 31 December 2022, including the different solar activities. First, the comparison with JASON-3 data illustrates that the quality of the three RT-GIM products over oceans is in great consistency with that of the IGSG during different levels of solar activity and the daily mean bias (MEAN) values in low and high solar activities are approximately 5 and 10 TECU, respectively. The root mean square (RMS) values under low and high solar activities can be up to 7 and 12 TECU. Furthermore, the dSTEC validation results present that the MEAN values of RT-GIM products from different IAACs at high- and mid-latitude stations are about 0.5 TECU, which is smaller than those at low-latitude stations at about 1 TECU over continental regions. The standard deviation (STD) and RMS values for various RT-GIM products are within 3 and 4 TECU at low latitudes, respectively. In terms of the comparison with IGSG, the result shows that IGS combined RT-GIM (IRTG) presents better consistency than CAS RT-GIM (CRTG) and WHU RT-GIM (WRTG) in 2021 and 2022, with average annual STD and RMS values of 2.56 and 2.78 TECU, respectively. The daily biases of the RT-GIM products relative to IGSG can reach 4 TECU in high solar activities and the daily STD and RMS values are mainly within the 5 to 6 TECU range, respectively.

ObjectivesTo evaluate the effect of additive and subtractive manufacturing on the accuracy (trueness and precision) of fixed partial denture patterns (FPDPs) used for casting or pressing. Materials and MethodsA 3-unit complete coverage FPD on mandibular right first premolar and first molar teeth was virtually designed. Using the design data, FPD patterns were fabricated from an additively manufactured resin (PR, ProArt Print Wax) and 2 CAD-CAM wax discs (YW, ProArt CAD Wax Yellow and BW, ProArt CAD Wax Blue) (n = 10). Each pattern was then digitized with a scanner (CEREC Primescan) and evaluated for 3D surface deviation at 4 different surfaces (overall, external, marginal, and intaglio surfaces) by using a 3D analysis software (Medit Link). Root mean square (RMS) values were automatically calculated. Data were analyzed by using Kruskal-Wallis and Dunn's post hoc tests for trueness and precision (α= 0.05). ResultsSignificant differences were found among the RMS values for overall (P<.001) and each surface (P≤.040) evaluated. PR had the highest overall (P≤.011) and intaglio surface (P≤.01) deviations, while the difference between YW and BW was not significant (P≥.199). PR had the highest (P≤.027) and BW had the lowest (P≤.042) external surface mean RMS values. BW had higher mean marginal RMS value than YW (P=.047). For precision, significant differences were observed among test groups only for marginal RMS values (P=.002). PR had lower precision than BW (P=.002). ConclusionsBW and YW FPDPs mostly had higher trueness compared with PR FPDPs. However, considering relatively smaller deviations at marginal and intaglio surfaces and the fact that patterns mostly had similar precision, clinical fit of FPDs fabricated by using tested patterns may be similar. Clinical SignificanceDefinitive 3-unit fixed partial dentures fabricated by using tested patterns may be similar. However, FPDs fabricated with tested additively manufactured resin patterns might result in more chairside adjustments than those fabricated with tested subtractively manufactured wax patterns.

To investigate the influence of different gingival colors and finish line locations on the accuracy of intraoral scans for complete-arch tooth preparation. Ten complete-arch maxillary models with 5 different gingival colors [light pink (LP), dark pink (DP), orange (Or), brown (Br), and purple (P)] and 2 different finish line locations [equigingival (Eq) and subgingival (Sb)] were used. Ten scans of each reference model were made with an intraoral scanner and exported as STL files. Assessment of precision and trueness was conducted with 3D analysis software. Each STL file was individually aligned with the reference scan and 3D differences were calculated using the root mean square (RMS) value. Data were statistically analyzed using 2-way ANOVA and Tukey HSD tests (α=.05). Regarding trueness, significant differences were found between different gingival colors and finish line locations. The highest mean RMS value was found in the gingival color group of Or with Sb finish line. Regardless of the finish line location applied, significantly lower RMS values were found in the gingival color groups of Br and P. Regarding precision, finish line location significantly influenced the mean RMS values of LP, DP, and Or. Regardless of the finish line location applied, significantly lower RMS values were obtained in the gingival color groups of Br and P. Gingival color influenced the scan accuracy of complete-arch tooth preparation. When the gingival color was a darker gingival color, the scan accuracy was improved, especially in the case of a subgingival finish line location.

The objective of the present study is to develop a vibration fatigue life prediction model for ball grid array (BGA) solder joint. In this study, 3D global/local finite element models were first constructed with MSC/PATRAN code. For the global model including BGA package soldered onto the printed wiring board (PWB), linear finite element dynamic analyses with an excitation normal to the PWB were conducted using MSC/NASTRAN code to determine the dynamic responses at the two ends of BGA solder joint. In these analyses, a single-degree-of-freedom system was assumed. A steady-state harmonic (or frequency sweep) response provides phase angle values while a random response furnishes the power spectral densities as well as their root mean square (RMS) values. For the local model having a refined mesh to simulate the local region in detail, a linear finite element static analysis was conducted by applying the derived RMS values with their corresponding phase angles to this model (at the two ends of the critical corner solder joint) in order to determine the solder effective stress/strain RMS value. A vibration fatigue life model, evolved from an empirically derived formula of universal slopes based on high-cycle fatigue test data, was established. This model combined with a three-band technique and the derived solder effective strain was then used to predict the BGA solder joint survivability/durability. This prediction will be compared to test results, which will be provided by in-house on-going R&D, to validate the proposed BGA solder joint vibration fatigue life prediction model. An example of a 600-pin plastic BGA soldered onto the various locations of the PWB was illustrated in the present study.

The aim of this randomized controlled crossover study was to investigate the effect of a bout of unaccustomed eccentric exercise (ECC) followed by a consecutive bout of the same intensity on local muscle blood flow, amplitude, and frequency of the electromyographic (EMG) signal from the exercised tibialis anterior muscle. Sixteen healthy male participants (age, 25.7 (0.6) years; body mass index 24.8 (1) kg·m(-2) participated in this study. Two identical bouts of high-intensity ECC were performed on the tibialis anterior muscle 7 days apart. Control sessions involving no exercise were performed 4 weeks either before or after the exercise sessions. Changes in local total blood flow [ΔtHb], EMG root mean square, and median power frequency were recorded during isometric maximum voluntary contraction of ankle dorsiflexion. Measurements were performed before, immediately after, and the day after both ECCs (ECC1 and ECC2). The participants rested quietly in a chair in the control session. Eccentric exercise 1 led to a significant decrease in [ΔtHb] on the day after (p ≤ 0.05), whereas ECC2 did not. Median power frequency decreased significantly in ECC2 compared with ECC1 (p < 0.01). Root mean square was unchanged in all the instants. The present study showed that adaptation is depicted in the local muscle blood flow and the frequency contents of the EMG after an unaccustomed ECC inducing muscle soreness. These alterations provide a potential mechanism for a rapid adaptation, which decreases susceptibility of the muscle to develop further soreness in the subsequent ECC bout.

A siliciclastic gas reservoir is analyzed through two seismic attributes, root mean square (RMS) ampli-tude and reservoir to shadow mono frequency (RSMF) to detect and quantify porosity and gas accumu-lation. The objectives are to apply forward modeling to design the interval for amplitude mapping to de-lineate porosity; to analyze the amplitude of the frequency to generate the RSMF map; and to validate the RMS amplitude map with porosity, and the RSMF map with gas test results. One well was modeled for two cases, a tight and porous reservoir, to establish an appropriate RMS amplitude extraction window for reservoir porosity. The amplitude around the reservoir was extracted and validated by wells. The seismic volume is decomposed in the frequency domain for the gas detec-tion technique. This technique measures the amplitude attenuation in the dominant frequency between the reservoir level and the zone just beneath it to produce the RSMF map, with the assumption that the frequency amplitude attenuation increases while passing through the gas reservoir. The RSMF map was validated by the normalized gas test results of several wells. The forward modeling indicates that up to 20 ms below the reservoir is an optimum window to corre-late the targeted reservoir with the RMS amplitude. The RMS amplitude was found to be directly pro-portional to porosity, with the modeled tight reservoir case having lower RMS amplitude than the porous reservoir case within the optimum window. The RMS amplitude response for the modeled tight reservoir case almost matches the in-situ case. There is a correlation coefficient of approximately 70% between the average reservoir porosity of the wells and the RMS amplitude map extracted from the seismic volume within the optimum window. At the dominant frequency of 20 Hz, a correlation coeffi-cient of around 82% is observed between the gas test results and amplitude attenuation. The RMS and RSMF attributes are affected by seismic amplitude preservation as well as signal-to-noise ratio, which can impact the level of uncertainty between these two attributes and the extracted maps. The integration of RMS amplitude and RSMF attributes complemented the characterization of the si-liciclastic gas reservoir for detecting high porosity zones with gas accumulations. Zones with high RMS amplitude and attenuation were highlighted to be targeted for well placement.

The statistical properties of acoustic emission signals for tool condition monitoring (TCM) applications in mechanical lathe machining are analyzed in this paper. Time series data and root mean square (RMS) values at various tool wear levels are shown to exhibit features that can be put into relation with aging in both cases. In particular, the histograms of raw data show power-law distributions above a cross-over value, in which newer cutting tools exhibit more numerous larger events compared with more worn-out ones. For practical purposes, statistics based on RMS values are more feasible, and the analysis of these also reveals discriminating age-related features. The assumption that experimental RMS histograms follow a Beta (β) distribution has also been tested. The residuals of the modeling β functions indicate that the search for a more appropriate fitting function for the experimental distribution is desirable.

In this work the problem of regulation of the Root Mean Square (RMS) value of the current for Series Resonant Converter (SRC) is addressed. The self-oscillating behavior is ensured by an amplitude modulation like control law and the RMS value is estimated with a proposed hybrid system. The closed-loop regulation is done with a Proportional-Integral (PI) controller with anti-windup scheme, and a set of Linear Matrix Inequalities (LMIs) is introduced to tune the gains. The knowledge of a reference trajectory is not needed to implement the controller, and it is shown to be effective in simulation considering uncertain parameters.

Motor cortical points are linked by intrinsic horizontal connections having a recurrent network topology. However, it is not known whether neural activity can propagate over the area covered by these intrinsic connections and whether there are spatial anisotropies of synaptic strength, as opposed to synaptic density. Moreover, the mechanisms by which activity spreads have yet to be determined. To address these issues, an 8 × 8 microelectrode array was inserted in the forelimb area of the cat motor cortex (MCx). The centre of the array had a laser etched hole ∼500 μm in diameter. A microiontophoretic pipette, with a tip diameter of 2-3 μm, containing bicuculline methiodide (BIC) was inserted in the hole and driven to a depth of 1200-1400 μm from the cortical surface. BIC was ejected for ∼2min from the tip of the micropipette with positive direct current ranging between 20 and 40 nA in different experiments. This produced spontaneous nearly periodic bursts (0.2-1.0 Hz) of multi-unit activity in a radius of about 400 μm from the tip of the micropipette. The bursts of neural activity spread at a velocity of 0.11-0.24 ms⁻¹ (mean=0.14 mm ms⁻¹, SD=0.05)with decreasing amplitude.The area activated was on average 7.22 mm² (SD=0.91 mm²), or ∼92% of the area covered by the recording array. The mode of propagation was determined to occur by progressive recruitment of cortical territory, driven by a central locus of activity of some 400 μm in radius. Thus, activity did not propagate as a wave. Transection of the connections between the thalamus and MCx did not significantly alter the propagation velocity or the size of the recruited area, demonstrating that the bursts spread along the routes of intrinsic cortical connectivity. These experiments demonstrate that neural activity initiated within a small motor cortical locus (≤ 400 μm in radius) can recruit a relatively large neighbourhood in which a variety of muscles acting at several forelimb joints are represented. These results support the hypothesis that the MCx controls the forelimb musculature in an integrated and anticipatory manner based on a recurrent network topology

Reservoir hydrocarbon potential of the Miocene Agbada Formation using RMS amplitude map and hydraulic flow unit model, Hatch Field offshore, Niger Delta Basin, Nigeria

The roughness of the contact surface exerts a vital role in rubbing. It is still a significant challenge to understand the microscopic contact of the rough surface at the atomic level. Herein, the rough surface with a special root mean square (RMS) value is constructed by multivariate Weierstrass–Mandelbrot (W–M) function and the rubbing process during that the chemical mechanical polishing (CMP) process of diamond is mimicked utilizing the reactive force field molecular dynamics (ReaxFF MD) simulation. It is found that the contact area A/A0 is positively related with the load, and the friction force F depends on the number of interfacial bridge bonds. Increasing the surface roughness will increase the friction force and friction coefficient. The model with low roughness and high lubrication has less friction force, and the presence of polishing liquid molecules can decrease the friction force and friction coefficient. The RMS value and the degree of damage show a functional relationship with the applied load and lubrication, i.e., the RMS value decreases more under larger load and higher lubrication, and the diamond substrate occurs severer damage under larger load and lower lubrication. This work will generate fresh insight into the understanding of the microscopic contact of the rough surface at the atomic level.