A Review of Low-Power Static Random Access Memory (SRAM) Designs

This research paper proposes a low-power, high-stability 8T static random access memory (SRAM) cell. The proposed SRAM cell is a modified structure of the conventional 6T SRAM cell. The introduction of two diode-connected transistors in the pull-down network of the conventional 6T SRAM cell gives the proposed 8T SRAM cell structure. The presence of diode-connected transistors improves the power and noise performances of the proposed cell as compared to those of the conventional bit cells. The power consumption and static noise margin (SNM) of the suggested SRAM cell are calculated for write, hold and read operations. Also, the write and read delays of the proposed and conventional bit cells are observed. The power, speed, noise margin and area of the proposed 8T SRAM cell are compared with those of some of the existing SRAM cells. In comparison to conventional SRAM cells, the proposed cell consumes less power and has higher stability, according to the study. A novel dual-supply ([Formula: see text][Formula: see text]V and [Formula: see text][Formula: see text]V or 200[Formula: see text]mV) concept is applied for the existing and proposed SRAM cells. The noise and power performances of SRAM cells are well improved under the condition of dual supply as compared to the conventional supply voltage ([Formula: see text][Formula: see text]V and [Formula: see text][Formula: see text]V). A [Formula: see text] memory array of the proposed 8T SRAM cell is formed and the performance of the array structure is compared with that of [Formula: see text] array of the conventional 6T SRAM cell. The layouts of existing and proposed SRAM cells are illustrated. The simulation is carried out using the Cadence Virtuoso simulation EDA tool in 90-nm CMOS technology.

-As the demand for low-power, high-performance memory systems grows, the design of efficient SRAM (Static Random Access Memory) cells becomes increasingly crucial. This paper explores the power consumption, performance, and stability of two SRAM cell designs: the conventional 6T and the Single Ended 6T SRAM. While the conventional 6T SRAM is prone to read disturb noise and high leakage power, it remains widely used due to its simplicity and compactness. To address these issues, the Single Ended 6T SRAM cell is introduced as an alternative, which reduces both power consumption and area while maintaining competitive performance. The study provides a detailed analysis of static and dynamic power consumption, read/write stability, and overall energy efficiency for both cell architectures. Simulation results show that the Single Ended 6T SRAM offers significant improvements in power reduction without compromising speed, making it a promising solution for future low-power, high-performance memory applications. Keywords— SRAM cell, Pre-Charge Circuits, Sense Amplifiers, and Single-Ended vs. Conventional 6T SRAM Cell.

This article presents a comprehensive assessment on the 6T static random access memory (SRAM) cell with 7-nm FinFET technology by implementing quantum physics-based device-circuit cooptimization. Seven key device design parameters and their multiple impacts on a 6T SRAM cell are systematically evaluated, focusing on materials band engineering, device design, circuit parameters tradeoff, and variation control. The area of SRAM cell under the same Fin quantization scheme remains constant in all evaluations. To the best of our knowledge, the most comprehensive discussion about circuit optimization from multiple device design parameters perspective is presented. Based on our cooptimization scheme, a SRAM cell is effectively designed. For a low-power and robust SRAM cell design, we achieve 56.7% reduction in leakage, 7.9% improvement in hold noise margin (HNM), 8.6% improvement in read noise margin (RNM), and 10.8% improvement in write margin (WM) at the expense of 19.3% increase in delay under design space of gate length (Lg) and spacer thickness (TSPC). For a high-speed SRAM cell design, we recommend focusing on the optimization of architecture and peripheral circuits. This framework not only has the advantages of easy implementation, technology-friendly, and high accuracy, but also suitable for path-finding researches on 5-nm node and beyond.

Design of high stability, low power and high speed 12 T SRAM cell in 32-nm CNTFET technology

Low power and noise tolerant static random access memory (SRAM) cells are in high demand today. This paper presents a stable differential SRAM cell that consumes low power. The proposed cell has similar structure to conventional 6T SRAM cell with the addition of two buffer transistors, one tail transistor and one complementary word line. Due to stacking effect, the proposed cell achieves lower power dissipation. In this paper, impact of process parameters variations on various design metrics of the proposed cell are presented and compared with conventional differential 6T (D6T), transmission gate-based 8T (TG8T), and single ended 8T (SE8T) SRAM cells. Impact of process variation, like threshold voltage and length, on different design metrics of an SRAM cell like, read static noise margin (RSNM), read access time ( ${T_{\mathrm{RA}}}$ ), and write access time ( ${T_{\mathrm{ WA}}} $ ) are also presented. The proposed cell achieves ${1.12{\times } /{\mathrm{ 1}}.{\mathrm{ 43}}{\times } /{\mathrm{ 5}}.{\mathrm{ 62}}\times } $ improvement in ${T_{\mathrm {RA}}}$ compared to TG8T/D6T/SE8T at a penalty of $ {1.1{\times } /{4}.{88}\times }$ in $ {T_{\mathrm{ WA}}} $ compared to D6T/TG8T and $ {1.19{\times } /1.18\times } $ in read/write power consumption compared to D6T. An improvement of $ {\rm 1.{\mathrm{ 12}}{\times } /{\mathrm{ 2}}.{\mathrm{ 15}}\times } $ in RSNM is observed compared to D6T/TG8T. The proposed cell consumes $ {5.38\times } $ less power during hold mode and also shows ${2.33\times } $ narrower spread in hold power @ $ {V_{\mathrm{ DD}} = 0.{\mathrm{ 4}}}$ V compared to D6T SRAM cell.

In modern technology era, the demand for Static Random Access Memory (SRAM) cells has been greatly increased due to its wide variety of applications. Power consumption, speed, read stability and leakage issues are the major design challenges related to SRAM. This paper presents a novel SRAM cell based on Multiple Supply Voltages and non-precharged RBL (MS-N10T) and also shows the comparison of various SRAM cells based on lector, sleep transistors and Transmission gate (TG) to reduce the power consumption when compared to LP10T. The SRAM cell MS-N10T when used in combination of TG and sleep transistors (TGNS-13T) further reduces the power consumption. The analysis further shows that the SRAM, TGNS13T reduces the power consumption approximately by 70-80%. On the Other hand, the LC14T SRAM cell enhances the stability approximately by 80-85%. The major objective of this work is to reduce the power consumption with marginal increase in propagation delay and to improve read stability so as to meet the challenges of advancements in technologies. All the various SRAM architectures are implemented using Cadence 45nm CMOS technology.  Â

We present a hybrid nanoelectromechanical (NEM)/CMOS static random access memory (SRAM) cell, in which the two pull-down transistors of a conventional CMOS six transistor (6T) SRAM cell are replaced with NEM relays. This SRAM cell utilizes the infinite subthreshold slope and hysteretic properties of NEM relays to dramatically increase the cell stability compared to the conventional CMOS 6T SRAM cells. It also utilizes the zero off-state leakage of NEM relays to significantly decrease static power dissipation. The structure is designed so that the relatively long mechanical delay of the NEM relays does not result in performance degradation. Circuit simulations are performed using a VerilogA model of a NEM relay. Compared to a 65nm CMOS 6T SRAM cell, when 10nm-gap NEM relays (pull-in voltage = 0.8V, pull-out voltage = 0.2V, on resistance = 1ki2) are integrated, hold and read static noise margin (SNM) improve by ~110% and ~250%, respectively. In addition, static power dissipation decreases by ~85%. The write delay decreases by ~60%, while read delay decreases by ~10%. The advantages in SNM and static power dissipation are expected to increase with scaling.

A low power CMOS Static Random Access Memory (SRAM) based Field Programmable Gate Arrays (FPGA) architecture is being presented in this paper. The architecture presented here is based on CMOS logic and CMOS SRAMs that are used for on-chip dynamic reconfiguration. This architecture employs the fast and low-power SRAM blocks that are based on 10T SRAM cells. These blocks are employed in fast access of the configuration bits by using the shadow SRAM technique. The dynamic reconfiguration delay is being hidden behind the computation delay through the use of shadow SRAM cells. The combined effect of both the SRAM memory cells and the shadow SRAM scheme enables to support in reducing the delay and also to achieve reduced power consumption. Experimental results show reduced delay of about 8.035ns and power consumption of about 0.015W for the 10T SRAM memory cell with an overhead in area, relative to 4T and 6T SRAM cells. Also, the experimental results include the values of delay of about 8.979ns and power consumption of about 0.052W, achieved for the LB of FPGA architecture which employs CMOS SRAMs using the 10T SRAM memory cells in it.

As is known in the art, it is relatively difficult to write a logic ‘1’ to the five-transistor (5T) static random access memory (SRAM) cell if the SRAM cell currently stores a logic ‘0’. In this paper, we proposed a 5T SRAM cell and a cell voltage control circuit coupled to provide power to the SRAM cell. The cell voltage control circuit supplies the SRAM cell with the HVDD supply voltage if the SRAM cell is in a read mode. If the SRAM cell is being written or during a standby mode, the cell voltage control circuit supplies the SRAM cell with the LVDD supply voltage that is less than the HVDD supply voltage. Several HSPICE simulations show that the proposed SRAM cell provides an improvement in SRAM cell topology by providing an efficient solution to the write ‘1’ issue.

Variability-aware 7T SRAM circuit with low leakage high data stability SLEEP mode

In this paper, we propose a radiation-tolerant by design 12 transistor (RTBD 12T) based Static Random Access Memory (SRAM) cell for deep space application. The designed SRAM cell can effectively tolerate radiation events. It exhibits high resilience towards radiation upsets and accordingly three out of four nodes of the cell are fully immune to radiation upsets, and it has a critical charge (QC) equal to 1.6 fC making it a more promising choice for deep space application. The design metrics of the proposed SRAM cell are compared with a few conventionally used SRAM cells like 6T, Quad node (QUATRO 10T) SRAM, Quadruple cross coupled storage cells (QUCCE 12T) and Writability Enhanced (WEQUATRO). The higher read stability is validated by the read static noise margin (RSNM) analysis in which the proposed cell achieves higher noise margin as compared to other SRAM cells. The proposed 12TSRAM cell exhibits improved results in terms of hold power, which is $\left( {0.86 \times } \right),\left( {0.40 \times } \right)$ and $\left( {0.74 \times } \right)$ compared to that of QUATRO 10T, QUCCE 12T and WEQUATRO, respectively.

SRAM (Static Random Access Memory) has become a major key component in many VLSI Chips, due to its high storage density and quick access time, it has become a popular data storage device. SRAM has played a significant role in the global VLSI sector. Due to the significant increase of low power and low voltage memory systems in recent times, SRAM has been prioritised in the research sector. This is owing to the increased demand for high-end devices, IC memory cards, and other communication devices, as well as the advancement of portable battery-operated devices. The power and area of a low-power 6T SRAM cell design are assessed in this research. This work describes the design and implementation of a 6T SRAM cell in standard CMOS process technology at 180nm, 90nm and 45nm nodes. In the Cadence Virtuoso Software, this simulation was run. The Static Noise Margin has been used to analyse the performance of SRAM cells. The schematic, transient simulation, and DC analysis are all included in this work.

<p>In Very Large Scale Integration (VLSI) design, device scaling is restricted due to subthreshold swing limitations and short channel effects. This article discusses the role of different power reduction techniques in the implementation of 14 nm fin-shaped field-effect transistor (FinFET) centered static random access memory (SRAM) cells with good subthreshold swing and reduced short channel effects (SCE). Dynamic threshold and power gating are incorporated in SRAM cells to advance the memory cell performance by reducing static power dissipation in standby mode. The power analysis was performed on different SRAM cells with different transistor count i.e., 6, 7, 8, and 9. The performance of SRAM cell is analysed in power dissipation and is reduced by 20% using power gating method and in dynamic threshold it is reduced to nano watts due to less leakage power.</p>

Static Random Access Memory (SRAM) technology is the latest technology must advance to satisfy the high-speed performance and low power consumption requirements of contemporary devices. The design, testing, and validation of SRAM cells with configurations ranging from six transistors (6T) to ten transistors (10T) are thoroughly examined in this research work. The study's main goal is to pinpoint the crucial elements that affect SRAM cell performance, such as data retention voltages, power consumption, delay factors, stability measures, and noise margins. Existing SRAM designs and their drawbacks are assessed through a thorough literature review, emphasizing the need for innovative SRAM design techniques. The process includes a thorough examination of important variables and the design and testing of several SRAM cell designs using sophisticated simulation tools. To guarantee robustness and reliability, every design from 6T to 10T is painstakingly created, simulated, and verified against a series of predetermined scenarios. The findings show how several SRAM layouts compare in terms of power efficiency, delay, stability, noise margin, and area efficiency. The study's conclusions offer helpful recommendations for improving SRAM designs in the future by weighing the trade-offs between stability, speed, and power consumption. By providing tested design methodologies that improve the performance and efficiency of SRAM cells, this research makes a substantial contribution to the field of semiconductor technology and meets the expanding demands of contemporary electronic gadgets.

SummaryDriven by technologies such as machine learning, artificial intelligence, and internet of things, the energy efficiency and throughput limitations of the von Neumann architecture are becoming more and more serious. As a new type of computer architecture, computing-in-memory is an alternative approach to alleviate the von Neumann bottleneck. Here, we have demonstrated two kinds of computing-in-memory designs based on two-surface-channel MoS2 transistors: symmetrical 4T2R Static Random-Access Memory (SRAM) cell and skewed 3T3R SRAM cell, where the symmetrical SRAM cell can realize in-memory XNOR/XOR computations and the skewed SRAM cell can achieve in-memory NAND/NOR computations. Furthermore, since both the memory and computing units are based on two-surface-channel transistors with high area efficiency, the two proposed computing-in-memory SRAM cells consume fewer transistors, suggesting a potential application in highly area-efficient and multifunctional computing chips.