A Self-Configuring TMR Scheme Utilizing Discrepancy Resolution

Nowadays, FPGAs are used in many safety-critical applications. They are mainly subjected to Single Event Upsets (SEUs) that can flip the state of a memory cell, thereby forcing the circuit to produce an erroneous output. Fault-tolerant techniques are used to mitigate these errors. Triple Modular Redundancy (TMR) is one of the most commonly used fault-tolerant techniques in FPGAs. However, the voter is a single point of failure. This paper proposes a fault secure TMR voter design. This voter is analyzed according to its FPGA implementation. SEUs, Single Event Transients (SETs) as well as single stuck-at-0(1) faults are considered. In the presence of these faults, this voter will always produce the correct output or will give an indication of the presence of an error. Alternating Logic is utilized in the design to help with error detection while Dynamic Partial Reconfiguration (DPR) is used for error recovery.

PurposeTraditionally, each time a new design for a finite impulse response (FIR) filter is required, a new algorithm has to be developed specially for the FIR filter. Furthermore, corresponding hardware architecture must be designed specially to meet the requirement of the FIR specifications. The purpose of this paper is to propose an arithmetic logic unit (ALU)‐based universal FIR filter suitable for realization in field programmable gate arrays (FPGA), where various FIR filters can be implemented just by programming instructions in the ROM with identical hardware architecture.Design/methodology/approachRather than multiplier‐accumulator‐based architecture for conventional FIR, the proposed ALU architecture implements the FIR functions by using accumulators and shift‐registers controlled by the instructions of ROM. Furthermore, time division multiplexing access (TDMA) technique is employed to reduce the chip size. In addition, the proposed FIR architecture is verified in a SOC hardware and/or software co‐emulation system.FindingsAn ALU‐based universal FIR filter suitable for realization in FPGA is designed and verified in a SOC hardware/software co‐emulation system with example of a 64‐tap FIR filter design.Originality/valueA software‐based design method as well as TDMA scheme for the ALU‐based FIR filter are introduced, making FIR filter architecture universal, programmable, and consuming less FPGA resources.

Digital filters play a central role in modern Digital Signal Processing (DSP) systems. Finite Impulse Response (FIR) filters can provide solutions with guaranteed stability and linear phase. However, the main disadvantage of conventional FIR filter designs is that they become computationally complex, especially in applications demanding narrow transition bandwidths. Therefore, designing FIR filters with very stringent specifications and a low complexity is currently an important challenge. In this chapter, a review of the recent methods to efficiently design low-complexity linear-phase FIR filters is presented. The chapter starts with an introduction to linear-phase FIR digital filters. Then, an overview of the design methods that have been developed in literature to design low-complexity FIR filters is presented. Finally, the most common and recent of these methods along with their corresponding special structures are explained.

Digital filters play a central role in modern digital signal processing (DSP) systems. Finite impulse response (FIR) filters can provide solutions with guaranteed stability and linear phase. However, the main disadvantage of conventional FIR filter designs is that they become computationally complex, especially in applications demanding narrow transition bandwidths. Therefore, designing FIR filters with very stringent specifications and a low complexity is currently an important challenge. In this chapter, a review of the recent methods to efficiently design low-complexity linear-phase FIR filters is presented. The chapter starts with an introduction to linear-phase FIR digital filters. Then, an overview of the design methods that have been developed in literature to design low-complexity FIR filters is presented. Finally, the most common and recent of these methods along with their corresponding special structures are explained.

Dynamic Partial Reconfiguration is an important feature of modern FPGAs as it allows for better exploitation of FPGA resources over time and space. The Internal Configuration Access Port (ICAP) enables DPR from within an FPGA chip, leading to the possibility of fully autonomous FPGA-based systems. This paper presents a novel high performance and fault-tolerant ICAP controller which can operate at a high speed and recover from emerging faults. Test results showed that our ICAP controller is 25 times faster than the Xilinx' XPS_HWICAP IP core. We demonstrate the use of Triple Modular Redundancy (TMR) in some of the ICAP controller components which have the ability to reconfigure the rest of the ICAP controller when faults are detected. This method is shown to have a 49% smaller area footprint compared to traditional full TMR.

WITHDRAWN: An Optimistic Design of 16-Tap FIR Filter with Radix-4 Booth Multiplier Using Improved Booth Recoding Algorithm

In Digital wireless communication system Finite Impulse Response (FIR) filter is used fundamentally pipelined as well as support Multiplication with Accumulation scheme (MAC) that results in important save of calculation. Efficient area along with delay recognition of great order FIR filters for update applications have been achieved by the opportunity of recognition of block FIR filter in transpose form organization. The projected transpose form block filter of update applications are developed by a general carry select adder based architecture. Secured digital FIR filter block is implemented by a pepped-up design using the MAC scheme. Booth multiplier has been used in MAC scheme. The proposed method has less area also delay than conventional filter.

Background/Objectives: FIR filters play a vital role in signal processing applications. This research work presents a low power and high speed efficient buffer based Distributed Algorithms and it is analyzed with Electro Cardio Gram (ECG) signal Finite Impulse Response (FIR) filter design. Methods/Statistical Analysis: The proposed FIR filter is designed using buffer based DA and it is simulated and synthesized using Cadence digital labs. This is compared with different architectures such as conventional DA, separated look up table DA and LUT less DA. Findings: Synthesis report shows that the proposed design has 52% less power dissipation compared with the conventional DA, 21% reduction in delay with separated Look Up Table (LUT) DA and 8% reduction in area with LUT less DA. Conclusion/Improvements: Presently this method is applied for ECG signal input with 16-tap FIR filter. This can be extended for higher order filters to achieve better performance.

Application specific integrated circuits are used to provide real-time performance of handheld devices within the compact physical size and low energy dissipation. However, these circuits are inflexible for any modification like redesign and refabrication. Reconfigurable architectures are promising alternative for conventional computing devices such as application-specific integrated circuits. It provides high-level flexibility to adapt the applications through dynamic hardware customization even after fabrication. A reconfigurable computing system design considers the peculiarities of the targeted application domain along with architectural issues like dynamic reconfiguration, partial reconfiguration, hardware/software co-design and context management. A brief survey has been carried out to understand the concepts and applications of CGRA, FPGA, SoC, NoC, MPSoC, dynamic partial reconfiguration, hardware/software co-design, design-space exploration, multi-objective optimization, genetic algorithm and reconfigurable computing on wireless communications. This paper deals with the survey on modeling, design, implementation and evaluation of coarse-grained dynamically reconfigurable processor architectures targeting the real-time embedded computing domain.

The demand for cost-effective digital filters in near-sensor computing has aroused interest in stochastic computing (SC) as a promising alternative to traditional binary approaches. This study investigates in detail the error tolerance and hardware cost of SC-based digital filters of both the finite and infinite impulse response (FIR and IIR) types, focusing on their stochastic number generation and addition methods. We demonstrate that SC filters need only about half the area and power of binary designs under error-free conditions, though with a slight reduction of accuracy. Furthermore, these filters exhibit strong error resilience, with only 4X and 6X performance degradation under a 3% bit-flip rate, significantly outperforming their binary (non-SC) counterparts. We also compare the error tolerance of SC filters against binary filters equipped with triple modular redundancy (TMR). Our results indicate that for FIR filters, SC-based designs remain far more error-tolerant than binary FIR filters with TMR. However, in the IIR case, the binary designs with TMR outperform SC-based IIR filters at higher error rates. These findings highlight the possible trade-offs between SC and binary implementations, with SC offering more robust error tolerance, significant area and power savings and manageable accuracy trade-offs in most cases. This work also underscores SC’s potential as an efficient, resilient approach for low-cost digital filtering in edge devices and near-sensor computing applications.

Time-interleaved analog-to-digital converter (TIADC) mismatch compensation filters are traditionally finite impulse response (FIR) filters. The advantages of using FIR filters are that FIR filters are inherently stable and that the design techniques are readily available. In this paper, we show that, infinite impulse response (IIR) mismatch compensation filters with guaranteed stability can be designed and for the same total number of coefficients, the IIR filters achieve better mismatch compensation than their FIR counterparts. We also show that for a given spurious frequency power, our new IIR TIADC compensation filter yields more than 30% saving in the total number of multiplier coefficients when compared to the conventional FIR TIADC compensation filters.

Nowadays, the communications and computations has been performed by Digital Finite Impulse Response (FIR) filter. FIR filter is predominantly used in DSP applications for efficient implementations. FIR filter is able to declare a firm linear phase frequency characteristic with any type of amplitude frequency characteristic in a DSP system. A reconfigurable FIR filter architecture has been implemented using Least Mean Square (LMS) algorithm in the proposed scheme. The proposed scheme achieves better performance when compared to an existing scheme. The proposed method has been implemented in ModelSim tool and efficiency has been calculated by using the device Virtex 6 Low Power in Xilinx ISE Design Suite 12.4.

Digital filter is an important fundamental component in digital signal processing (DSP) systems. Among the digital filters, the finite impulse response (FIR) filter is one of the most commonly used schemes. As a low-complexity hardware implementation technique, stochastic computing has been applied to overcome the huge hardware cost problem of high-order FIR filters. However, the stochastic FIR filter (SFIR) scheme suffers from long processing latency and accuracy degradation. In this paper, the bit stream representation noise is theoretically analyzed, and an adaptive scaling algorithm (ASA) is proposed to improve the accuracy of SFIR with the same bit stream length. Furthermore, a novel antithetic variables method is proposed to further improve the accuracy. According to the simulation results on a 64-tap FIR filter, the ASA and AV methods gain 17 dB and 6 dB on the signal-to-noise ratio (SNR), respectively. The hardware implementation results are also presented in this paper, which illustrates that the proposed ASA-AV-SFIR filter increases 4.6 times hardware efficiency with respect to the existing SFIR schemes.

Fractional sample interpolation with finite impulse response (FIR) filters is commonly used for motion-compensated prediction (MCP). The FIR filtering can be viewed as a signal decomposition using restricted basis functions. The concept of generalized interpolation provides a greater degree of freedom for selecting basis functions. We developed a generalized interpolation framework for MCP using fixed-point infinite impulse response and FIR filters. An efficient multiplication-free design of the algorithm that is suited for hardware implementation is shown. A detailed analysis of average and worst case complexities compared to FIR filter-based interpolation techniques is provided. Average bitrate savings of around 2.0% compared to an 8-tap FIR filter are observed over the high-efficiency video coding dataset at a similar worst case complexity.

Chapter 2 - Design and Implementation of Digital FIR Filters