Abstracts

Procedure 48 Separation and amperometric detection of hydrogen peroxide and l-ascorbic acid using capillary electrophoresis microchips

The effective design and control of a capillary electrophoresis (CE) microchip requires a thorough understanding of the electrokinetic transport phenomena associated with its microfluidic injection system. The present study utilizes a numerical simulation approach to investigate these electrokinetic transport processes and to study the control parameters of the injection process. Injection systems with a variety of different configurations are designed and tested, including the cross-form, T-form, double-T-form, variable-volume focused flow cross-form, and variable-volume triple-T-form configuration. Each injection system cycles through a predetermined series of steps in which the magnitudes and distributions of the applied electric field are precisely manipulated in order to effectuate a virtual valve. This study investigates the sample leakage effect associated with each of the injection configurations and applies the double-L, pullback, and focusing injection techniques to minimize the sample leakage effect. The injection methods presented in this paper have the exciting potential for use in high-quality, high-throughput chemical analysis applications and throughout the micro-total-analysis systems field.

This thesis focuses on the optimisation of capacitively coupled contactless conductivity detection for capillary and microchip electrophoresis and its applications in analytical chemistry. First, the effect of high excitation voltages and operation frequencies on the capacitively coupled contactless conductivity detector cell for conventional capillary electrophoresis is evaluated. The detector electrodes comprised two steel tubes cut from hypodermic needles, through which the capillaries were inserted. It is demonstrated that increasing excitation voltages from 25 V pp, to 250 Vpp improves the detection limits by a factor of 10. The high actuator voltage approach was also investigated for contactless conductivity detection on a glass-microchip device with ancm long channel. The detector electrodes formed part of the microchip and were placed on the microchip directly above the microchannel. In a separate project the simplification of on-microchip contactless conductivity detection was accomplished. This was achieved by integrating the detector electrodes on to a chip-holder specifically designed for this purpose. Thus the electrodes were a part of the holder, an improvement of the previous arrangement whereby the detector electrodes were situated on the microdevice. Finally the applications and advantages of the optimised high-voltage capacitively coupled contactless conductivity detection for inorganic and organic analysis were demonstrated. The separation and detection of 14 metal ions was accomplished in less than six minutes. The compatibility of this detector with non-UV transparent, polymer capillaries has been demonstrated. The detection of native amino acids has been evaluated. Part of the work was dedicated to the on-chip analysis of various classes of organic ions. The two immunoproteins human immunoglobulin M (IgM) and immunoglobulin G (IgG), were analysed in their unlabelled state on both capillary and lab-on-chip platforms. All species involved in an immunological interaction between IgM and IgG could be detected. A method for the analysis of selected basic pharmaceutical drug substances was developed. Detection limits comparable to those supplied by direct UV detection were obtained. Main component assays of selected pharmaceutical preparations have been demonstrated.

Electrochemical detection modes for microchip capillary electrophoresis

Electrophoretic migration and electroosmotic flow (EOF) combine to determine the migration rate of charged compounds in capillary electrophoresis (CE) and microchip capillary electrophoresis (MCE). Uncontrolled and unmeasured changes in EOF will lead to irreproducible peak migration times and poor peak quantitation. The two most common methods for measuring EOF for CE and MCE are detailed. Experimental results for application of the neutral marker method and the current monitoring method to EC are presented, and related calculations of EOF rates and electroosmotic mobility are described. The strengths and shortcomings of these two EOF measurement techniques are discussed. Additional approaches for studying and measuring EOF and for improving the reproducibility of migration times for CE and MCE are summarized.

Clinical studies have linked irregular concentrations of uric acid in urine to several diseases. Conventional methods for the measurement of uric acid are however temperature-dependent, expensive, and require labile reagents. The miniaturization of analytical techniques, specifically capillary electrophoresis, offers an ideal alternative for clinical analyses such as uric acid determination. The added benefits include reduced reagent and analyte consumption, decreased maintenance costs, and increased throughput and portability. A microchip capillary electrophoresis-electrochemical system for the analysis of uric acid in urine is described. The poly(dimethylsiloxane) (PDMS)/glass microchip utilizes amperometric detection via an off-chip platinum working electrode. Linear responses from 1 to 165 microM and 15 to 110 microM were found for dopamine and uric acid, respectively. The limit of detection for both compounds was 1 microM. Once characterized, the system was used to measure the concentration of uric acid in a dilute urine sample in less than 30 s. The measured uric acid concentration was verified with the uricase reaction and found to be acceptable. Six additional urine samples were evaluated with the microchip device and the uric acid concentration for each sample was found to be in the expected clinical concentration range.

The biopharmaceutical market is one of the fastest growing biotechnology markets. In order to ensure affordable and reliable therapeutics, the biopharmaceutical process has to be closely monitored. Capillary electrophoresis (CE) has proven to be a valuable technique for the analysis of product concentration, critical quality attributes, product and process-related impurities, and nutrients and metabolites in the cell culture medium. Capillary zone electrophoresis, capillary gel electrophoresis, and capillary isoelectric focusing are extensively used for product concentration, and size or charge heterogeneity determination. CE has a number of benefits for the analysis of upstream and downstream process-intermediates, including the ability to handle highly complex matrices found in process-intermediates, high resolving power, little sample preparation requirements, rapid analysis, and low solvent and sample consumption. The small sample volumes (nL range) are especially beneficial for microbioreactor analysis or clone selection experiments. The simple setup and the possibility for miniaturisation and automation using microchip CE provides great opportunities for on-site, real-time monitoring of the process. This review discusses CE applications in upstream and downstream processing of the last decade.

The direct measurement of lithium in whole blood is described. Using microchip capillary electrophoresis (CE) with defined sample loading and applying the principles of column coupling, alkali metals were determined in a drop of whole blood. Blood collected from a finger stick was mixed with anticoagulant and transferred onto the chip without extraction or removal of components. The electrokinetic transport of red blood cells inside the channels was studied to find sample loading conditions suitable for the analysis of lithium without injecting cells into the separation channel. Both bare glass chips and chips coated with polyacrylamide were used showing the behavior of the cells under different electroosmotic flow conditions. In serum a detection limit for lithium of 0.4 mmol/L was reached. Proteins quickly contaminated untreated chip surfaces but devices with coating gave reproducible electropherograms. In addition, potassium and sodium were also detected in the same separation run. To our knowledge, this is the first device to directly measure ions in whole blood with the use of capillary zone electrophoresis on a microchip.

Amino acids are essential compounds for living organisms, and their determination in biological fluids is crucial for the clinical analysis and diagnosis of many diseases. However, the detection of most amino acids is hindered by the lack of a strong chromophore/fluorophore or electrochemically active group in their chemical structures. The highly sensitive determination of amino acids often requires derivatization. Capillary electrophoresis is a separation technique with excellent characteristics for the analysis of amino acids in biological fluids. Moreover, it offers the possibility of precapillary, on-capillary, or postcapillary derivatization. Each derivatization approach has specific demands in terms of the chemistry involved in the derivatization, which is discussed in this review. The family of homocyclic o-dicarboxaldehyde compounds, namely o-phthalaldehyde, naphthalene-2,3-dicarboxaldehyde, and anthracene-2,3-dicarboxaldehyde, are powerful derivatization reagents for the determination of amino acids and related compounds. In the presence of suitable nucleophiles they react with the primary amino group to form both fluorescent and electroactive derivatives. Moreover, the reaction rate enables all of the derivatization approaches mentioned above. This review focuses on articles that deal with using these reagents for the derivatization of amino acids and related compounds for ultraviolet-visible spectrometry, fluorescence, or electrochemical detection. Applications in capillary and microchip electrophoresis are summarized and discussed.

Prospects of pulsed amperometric detection in flow-based analytical systems - A review

Electrochemical methods in conjunction with capillary and microchip electrophoresis

This study presents an experimental and numerical investigation on the use of high-resolution injection techniques to deliver sample plugs within a capillary electrophoresis (CE) microchip. The CE microfluidic device was integrated into a U-shaped injection system and an expansion chamber located at the inlet of the separation channel, which can miniize the sample leakage effect and deliver a high-quality sample plug into the separation channel so that the detection performance of the device is enhanced. The proposed 45° U-shaped injection system was investigated using a sample of Rhodamine B dye. Meanwhile, the analysis of the current CE microfluidic chip was studied by considering the separation of Hae III digested ϕx-174 DNA samples. The experimental and numerical results indicate that the included 45° U-shaped injector completely eliminates the sample leakage and an expansion separation channel with an expansion ratio of 2.5 delivers a sample plug with a perfect detection shape and highest concentration intensity, hence enabling an optimal injection and separation performance.

The emergence of drug-resistant bacteria and new or changing infectious pathogens is an important public health problem as well as a serious socioeconomic concern. Immunomagnetic separation-based methods create new possibilities for rapidly recognizing many of these pathogens. Nanomaterial-based techniques including fluorescent labeling by quantum dots as well as immunoextraction by magnetic particles are excellent tools for such purposes. Moreover, the combination with capillary electrophoresis in miniaturized microchip arrangement brings numerous benefits such as fast and rapid analysis, low sample consumption, very sensitive electrochemical and fluorescent detection, portable miniaturized instrumentation, and rapid and inexpensive device fabrication. Here the use of superparamagnetic particle-based fully automated instrumentation to isolate pathogen Staphylococcus aureus and its Zn(II)-containing proteins (Zn-proteins) is reported using a robotic pipetting system speeding up the sample preparation and enabling to analyze 48 real samples within 6 h. Cell lysis and Zn-protein extractions were obtained from a minimum of 100 cells with the sufficient yield for SDS-PAGE (several tens ng of proteins).

The first reported use of a carbon paste electrochemical detector for microchip capillary electrophoresis (CE) is described. Poly(dimethylsiloxane) (PDMS)-based microchip CE devices were constructed by reversibly sealing a PDMS layer containing separation and injection channels to a separate PDMS layer that contained carbon paste working electrodes. End-channel amperometric detection with a single electrode was used to detect amino acids derivatized with naphthalene dicarboxaldehyde. Two electrodes were placed in series for dual electrode detection. This approach was demonstrated for the detection of copper(II) peptide complexes. A major advantage of carbon paste is that catalysts can be easily incorporated into the electrode. Carbon paste that was chemically modified with cobalt phthalocyanine was used for the detection of thiols following a CE separation. These devices illustrate the potential for an easily constructed microchip CE system with a carbon-based detector that exhibits adjustable selectivity.

Native fluorescence detection of flavin derivatives by microchip capillary electrophoresis with laser-induced fluorescence intensified charge-coupled device detection