Adaptive Time Segment Analysis for Steady-State Visual Evoked Potential Based Brain-Computer Interfaces.

Objective. Brain–computer interface (BCI) technologies have been intensely studied to provide alternative communication tools entirely independent of neuromuscular activities. Current BCI technologies use electroencephalogram (EEG) acquisition methods that require unpleasant gel injections, impractical preparations and clean-up procedures. The next generation of BCI technologies requires practical, user-friendly, nonintrusive EEG platforms in order to facilitate the application of laboratory work in real-world settings. Approach. A capacitive electrode that does not require an electrolytic gel or direct electrode–scalp contact is a potential alternative to the conventional wet electrode in future BCI systems. We have proposed a new capacitive EEG electrode that contains a conductive polymer-sensing surface, which enhances electrode performance. This paper presents results from five subjects who exhibited visual or auditory steady-state responses according to BCI using these new capacitive electrodes. The steady-state visual evoked potential (SSVEP) spelling system and the auditory steady-state response (ASSR) binary decision system were employed. Main results. Offline tests demonstrated BCI performance high enough to be used in a BCI system (accuracy: 95.2%, ITR: 19.91 bpm for SSVEP BCI (6 s), accuracy: 82.6%, ITR: 1.48 bpm for ASSR BCI (14 s)) with the analysis time being slightly longer than that when wet electrodes were employed with the same BCI system (accuracy: 91.2%, ITR: 25.79 bpm for SSVEP BCI (4 s), accuracy: 81.3%, ITR: 1.57 bpm for ASSR BCI (12 s)). Subjects performed online BCI under the SSVEP paradigm in copy spelling mode and under the ASSR paradigm in selective attention mode with a mean information transfer rate (ITR) of 17.78 ± 2.08 and 0.7 ± 0.24 bpm, respectively. Significance. The results of these experiments demonstrate the feasibility of using our capacitive EEG electrode in BCI systems. This capacitive electrode may become a flexible and non-intrusive tool fit for various applications in the next generation of BCI technologies.

The application of the brain-computer interface (BCI) is massively helpful and advantageous for disabled people. Moreover, BCI is an arrangement of software and hardware interface that provides a direct interaction between the human brain and computer devices. Therefore, in this article, A steady state visual evoked potential (SSVEP)-based BCI system is presented to identify SSVEP components from multi-channel electroencephalogram (EEG) data by minimizing background noise using an adaptive spatial filtering method. Here, the proposed adaptive spatial filtering-based SSVEP component extraction (ASFSCE) model improves reproducibility among multiple trails and identifies targets efficiently by optimizing the Eigenvalue problem. Along with that, the proposed ASFSCE model minimizes computational complexity from O(G<sup>2</sup>) to to get high target identification accuracy with faster execution. Performance results are measured using the SSVEP dataset. In this dataset, 11 subjects are used to perform experiments and 256-channel EEG data is taken. The efficiency of the proposed ASFSCE model is measured in terms of mean target detection accuracy and mean information transfer rate (ITR) in bits per minute. The average detection accuracy and ITR are evaluated by considering 23 trials for each subject. The obtained detection accuracy is 93.47% and ITR is 308.23 bpm.

Brain–computer interfaces (BCIs), also known as brain–machine interfaces (BMIs), translate brain activity into new outputs that replace, restore, enhance, supplement or improve natural brain outputs. BCI research and development has grown rapidly for the past two decades. It is beginning to provide useful communication and control capacities to people with severe neuromuscular disabilities; and it is expanding into new areas such as neurorehabilitation that may greatly increase its clinical impact. At the same time, significant challenges remain, particularly in regard to translating laboratory advances into clinical use.

To enhance the information transfer rate (ITR) of a steady-state visual evoked potential (SSVEP)-based speller, more characters with flickering symbols should be used. Increasing the number of symbols might reduce the classification accuracy. A hybrid brain-computer interface (BCI) improves the overall performance of a BCI system by taking advantage of two or more control signals. In a simultaneous hybrid BCI, various modalities work with each other simultaneously, which enhances the ITR. In our proposed speller, simultaneous combination of electromyogram (EMG) and SSVEP was applied to increase the ITR. To achieve 36 characters, only nine stimulus symbols were used. Each symbol allowed the selection of four characters based on four states of muscle activity. The SSVEP detected which symbol the subject was focusing on and the EMG determined the target character out of the four characters dedicated to that symbol. The frequency rate for character encoding was applied in the EMG modality and latency was considered in the SSVEP modality. Online experiments were carried out on 10 healthy subjects. The average ITR of this hybrid system was 96.1 bit/min with an accuracy of 91.2%. The speller speed was 20.9 char/min. Different subjects had various latency values. We used an average latency of 0.2 s across all subjects. Evaluation of each modality showed that the SSVEP classification accuracy varied for different subjects, ranging from 80% to 100%, while the EMG classification accuracy was approximately 100% for all subjects. Our proposed hybrid BCI speller showed improved system speed compared with state-of-the-art systems based on SSVEP or SSVEP-EMG, and can provide a user-friendly, practical system for speller applications.

Estimating and approaching the maximum information rate of noninvasive visual brain-computer interface

Brain-computer interface (BCI) systems translate the human neurophysiological activities into commands through EEG analysis. Improving the BCI performances leads to faster and easier use and less fatigue. In this study, we proposed a new prepossessing approach to increase the robustness of a steady-state visual evoked potential (SSVEP) based BCI. Inspiring from the known properties of the SSVEP frequency components, the goal was to enhance the signal quality by making it more convenient to be interpreted by the decision-making step. We first investigated the potential to detect the deteriorating periods based on the physiological properties of the SSVEP. The proposed system localizes the intervals which can obscure the SSVEP frequencies by a new algorithm founded on the processing and the analysis of the instantaneous phase. The piecewise linear regression allows a sampler comprehension of the phase signal. Then, these intervals are filtered by the moving average filter to enhance the SSVEP quality. Finally, the decision making is made by the canonical correlation analysis (CCA) algorithm. The results of experiments, using real EEG signals from five subjects, show that the proposed approach significantly increases the performances in terms of accuracy and information transfer rate by about 7.3% and 3.85 bits/min, respectively, in case of 2 s segment length. On the other hand, the spatial filtering methods of the literature weaken the system performances.

In this paper, to develop a hybrid brain-computer interface based on Steady State Visual Evoked Potential(SSVEP) and P300, we validate a SSVEP brain-computer interface (BCI) with the hybrid stimuli of SSVEP and P300, and analyze the effect of P300 visual stimuli on the classification accuracy of the SSVEP BCI. The hybrid stimuli include the SSVEP stimuli, which consist of twochessboardimagespresented on a LCD screen and flashing at particular frequencies, respectively, and the P300 stimuli, which include nine characters and locate between the SSVEP stimuli. We extract the fundamental frequencies and second harmonics of the frequencies of the SSVEP stimulifrom EEG data as features, andapply a Fisher's linear discriminant analysis to build the classifier. The experimental results from three subjects show that the SSVEP potentials can be elicited well under the hybrid stimuli of SSVEP and P300, and the P300 stimuli under the hybrid condition have no significant effect on the SSVEP BCI. This work laysa foundationfor developing a hybrid BCIbased on SSVEP and P300.

Brain machine interfaces (BMIs) provide one of the important means to interact with external world for a patient who lost motor function by using brain electrical signals such as scalp electroencephalogram (EEG). The main function of BMIs is to detect, analyze and classify the modulation of EEG according to a user's intent and to decode it to demonstrate to others. Most of conventional BMIs with relatively high speed and high classification accuracy have a requisite that a user can open and move his/her eyes toward a target corresponding to user's intent and gaze at it. Locked-in patients, who have lost almost all motor function including facial muscle, cannot control the eye-movement as well as gaze. The present study aimed at developing a BMI which was independent of the eye-movement and eye-gaze as a final goal. In this paper, we discuss the feasibility of binary class of BMI available with eyes-closed condition using a recent our newly observation that the steady-state visual evoked potential (SSVEP) could be modulated by performing the mental tasks even in the eyes-close state. Temporal evolution of the modulation of SSVEP was investigated using the amplitude of SSVEP and Kullback-Leibler (KL) divergence. The amplitudes of fundamental SSVEP (10 Hz) averaged across 11 participants showed significant difference between the mental focusing task and relaxed runs from the onset of the flicker stimuli with the frequency of 10 Hz and the intensity of 5 lx, whereas those of the second harmonic SSVEP (20 Hz) gave only small difference without statistical significance. For the image recalling task, the amplitude differences between the fundamental SSVEPs in the task and relaxed conditions did not show significant difference, whereas the amplitude differences of the second harmonic SSVEP showed the main effect of the image recall task. The KL divergences for the fundamental SSVEP amplitude showed large differences at the onset of flicker stimuli and gradual decrease with time at P4 and O2 for the mental focus task, yet no such characteristic evolution was not seen in KL divergence for the second harmonic SSVEP. On the other hand, the KL divergences during the image recalling were increased with time for both the fundamental and second harmonic SSVEPs at most of the electrode sites. The classification accuracies of the proposed BMI exceeded 75 % in average across the subjects for both tasks using Fisher's linear discriminant analysis.

Brain-computer interface (BCI) systems have emerged as an augmentative technology that can provide a promising solution for individuals with motor dysfunctions and for the elderly who are experiencing muscle weakness. Steady-state visually evoked potentials (SSVEPs) are widely adopted in BCI systems due to their high speed and accuracy when compared to other BCI paradigms. In this paper, we apply combined magnitude and phase features for class discrimination in a real-time SSVEP-based BCI platform. In the proposed real-time system users gain control of a motorised bed system with seven motion commands and an idle state. Experimental results amongst eight participants demonstrate that the proposed real-time BCI system can successfully discriminate between different SSVEP signals achieving high information transfer rates (ITR) of 82.73 bits/min. The attractive features of the proposed system include noninvasive recording, simple electrode configuration, excellent BCI response and minimal training requirements.

Steady state visual evoked potential (SSVEP)-based brain-computer interface (BCI) has gained a lot of attention due to its robustness and high information transfer rate (ITR). However, transitioning well-controlled laboratory-oriented BCI demonstrations to real-world applications poses severe challenges for this exciting field. For instance, conducting BCI experiments usually requires skilled technicians to abrade the area of skin underneath each electrode and apply an electrolytic gel or paste to acquire high-quality SSVEPs from hair-covered areas. Our previous proof-of-concept study has proposed an alternative approach that employed electroencephalographic signals collected from easily accessible non-hair-bearing areas including neck, behind the ears, and face to realize an SSVEP-based BCI. The study results showed that, with proper electrode placements and advanced signal-processing algorithms, the SSVEPs measured from non-hair-bearing areas in off-line SSVEP experiments could achieve comparable SNR to that obtained from the hair-bearing occipital areas. This study extended the previous work to systematically investigate the costs and benefits of non-hair SSVEPs. Furthermore, this study developed and evaluated an online BCI system based solely on non-hair EEG signals. A 12-target identification task was employed to quantitatively assess the performance of the online SSVEP-based BCI system. All subjects successfully completed the tasks using non-hair SSVEPs with 84.08 ± 15.60% averaged accuracy and 30.21 ± 10.61 bits/min averaged ITR. The empirical results of this study demonstrated the practicality of implementing an SSVEP-based BCI based on signals from non-hair-bearing areas, significantly improving the feasibility and practicality of real-world BCIs.

The steady-state visual evoked potential (SSVEP) has been widely applied in brain-computer interfaces (BCIs), such as letter or icon selection and device control. Most of these BCIs used different flickering frequencies to evoke SSVEP with different frequency components that were used as control commands. In this paper, a novel method combining the time phase and EEG frequency components is presented and validated with nine healthy subjects. In this method, four different frequency components of EEG were classified out from four time phases. When the SSVEP is evoked and what is the frequency of the SSVEP is determined by the linear discriminant analysis (LDA) classifier in the same time to locate the target image. The results from offline analysis show that this method yields good performance both in classification accuracy and information transfer rate (ITR).KeywordsBrain-computer interfaces (BCIs)Electroencephalogram (EEG)Steady-state visual evoked potential (SSVEP)Time phase

Brain–computer interface (BCI) systems rely on the direct measurement of brain signals, such as event-related desynchronization (ERD), steady state visual evoked potentials (SSVEPs), P300s, or slow cortical potentials. Unfortunately, none of these BCI approaches work for all users. This study compares two conventional BCI approaches (ERD and SSVEP) within subjects, and also evaluates a novel hybrid BCI based on a combination of these signals. We recorded EEG data from 12 subjects across three conditions. In the first condition, subjects imagined moving both hands or both feet (ERD). In the second condition, subjects focused on one of the two oscillating visual stimuli (SSVEP). In the third condition, subjects simultaneously performed both tasks. We used logarithmic band power features at sites and frequencies consistent with ERD and SSVEP activity, and subjects received real-time feedback based on their performance. Subjects also completed brief questionnaires. All subjects could simultaneously perform the movement and visual task in the hybrid condition even though most subjects had little or no training. All subjects showed both SSVEP and ERD activity during the hybrid task, consistent with the activity in both single tasks. Subjects generally considered the hybrid condition moderately more difficult, but all of them were able to complete the hybrid task. Results support the hypothesis that subjects who do not have strong ERD activity might be more effective with an SSVEP BCI, and suggest that SSVEP BCIs work for more subjects. A simultaneous hybrid BCI is feasible, although the current hybrid approach, which involves combining ERD and SSVEP in a two-choice task to improve accuracy, is not significantly better than a comparable SSVEP BCI. Switching to an SSVEP BCI could increase reliability in subjects who have trouble producing the EEG activity necessary to use an ERD BCI. Subjects who are proficient in both BCI approaches might be able to combine these approaches in different ways and for different goals.

The dynamic clamp technology to implement artificial membrane or synaptic conductances is one of the most successful examples of closed-loop interactions with the nervous system for observation and control purposes (for a review see [1]). We recently proposed a generalization of the dynamic clamp concept to design goal-driven closed-loop interactions with biological systems beyond electrical stimulation and recording in the context of in vitro electrophysiology and animal ethology [2]. Following the same activity-dependent stimulation approach, we designed an assisted closed-loop (ACL) to optimize the efficiency of brain-computer interfaces (BCI) based on steady state visually evoked potentials (SSVEP) [3]. SSVEP based BCIs use multiple visual stimuli such as LEDs or regions on a screen flickering at different frequencies. A subject's brain generates electrical activity at the same fundamental frequency as the visual stimulus on which the subject has focused his/her attention. The ACL consists in the delivery of online information with regard to the control over the given BCI goal both to the human subject and to the system, resulting in an online adaptation of BCI stimuli properties, in this first proof of concept study the combination of the employed flicker frequencies (Figure ​(Figure1).1). The optimization process is realized by first performing a real-time closed-loop search for the best set of stimulation frequencies to achieve the given BCI goal, which informs the system about the most effective flicker frequencies to produce SSVEPs in a given subject. Secondly, a continuous auditory feedback informs the subject about the actual distance to a predefined detection threshold. Figure 1 The assisted closed-loop (ACL) provides online information to the system about the most effective flicker frequencies and to the human subject about the actual distance to the pre-defined SSVEP detection threshold by a continuous auditory feedback (speaker ... Our results show that this shared online information leads to an enhanced BCI efficiency, as compared to classic BCI protocols, by helping them to reach the BCI goal in their interaction. The analysis also shows that the ACL protocol takes into account interindividual variabilities. In particular, baseline resting state EEG measures seem to predict subjects' BCI performances, which indicates that the ACL based BCIs might be expanded to innovative new diagnostic/therapeutic tools for clinical contexts and as new paradigms for basic research. Taking all together, these results illustrate that assisted closed-loop protocols can reveal dynamics otherwise hidden under traditional stimulation techniques, provide control of regular and pathological states, induce learning processes, bridge between distinct levels of analysis and lead to automation of experiments. The proposed approach might have a large impact for applied uses, such as computer control and biomedical or prosthetic uses, but also in novel paradigms for neuroscientific and biomedical research.

Steady-state visual evoked potential (SSVEP) based brain-computer interfaces (BCIs) have achieved an information transfer rate (ITR) of over 300 bits/min, but abundant training data is required. The performance of SSVEP algorithms deteriorates greatly under limited data, and the existing time-shift data augmentation method fails to improve it because the phase-locked requirement between training samples is violated. To address this issue, this study proposes a novel augmentation method, namely phase-locked time-shift (PLTS), for SSVEP-BCI. The similarity between epochs at different time moments was evaluated, and a unique time-shift step was calculated for each class to augment additional data epochs in each trial. The results showed that the PLTS significantly improved the classification performance of SSVEP algorithms on the BETA SSVEP datasets. Moreover, under the condition of one calibration block, by slightly prolonging the calibration duration (from 48 s to 51.5 s), the ITR increased from 40.88 ±4.54 bits/min to 122.61 ± 7.05 bits/min with the PLTS. This study provides a new perspective on augmenting data epochs for training-based SSVEP-BCI, promotes the classification accuracy and ITR under limited training data, and thus facilitates the real-life applications of SSVEP-based brain spellers.

BackgroundBridging the gap between laboratory brain-computer interface (BCI) demonstrations and real-life applications has gained increasing attention nowadays in translational neuroscience. An urgent need is to explore the feasibility of using a low-cost, ease-of-use electroencephalogram (EEG) headset for monitoring individuals’ EEG signals in their natural head/body positions and movements. This study aimed to assess the feasibility of using a consumer-level EEG headset to realize an online steady-state visual-evoked potential (SSVEP)-based BCI during human walking.MethodsThis study adopted a 14-channel Emotiv EEG headset to implement a four-target online SSVEP decoding system, and included treadmill walking at the speeds of 0.45, 0.89, and 1.34 meters per second (m/s) to initiate the walking locomotion. Seventeen participants were instructed to perform the online BCI tasks while standing or walking on the treadmill. To maintain a constant viewing distance to the visual targets, participants held the hand-grip of the treadmill during the experiment. Along with online BCI performance, the concurrent SSVEP signals were recorded for offline assessment.ResultsDespite walking-related attenuation of SSVEPs, the online BCI obtained an information transfer rate (ITR) over 12 bits/min during slow walking (below 0.89 m/s).ConclusionsSSVEP-based BCI systems are deployable to users in treadmill walking that mimics natural walking rather than in highly-controlled laboratory settings. This study considerably promotes the use of a consumer-level EEG headset towards the real-life BCI applications.