Algorithmic and Combinatorial Analysis of Trapping Sets in Structured LDPC Codes

The error floor phenomenon, associated with iterative decoders, is one of the most significant limitations to the applications of low-density parity-check (LDPC) codes. A variety of techniques from code design to decoder implementation have been proposed to address the error floor problem, among which post-processors have shown to be both effective and implementation-friendly. In this paper, we take the inspiration from simulated annealing to generalize the post-processor design using three methods: quenching, extended heating, and focused heating, each of which targets a different error structure. The resulting post-processor is demonstrated to lower the error floors by two orders of magnitude for two structured code examples, a (2209, 1978) array LDPC code and a (1944, 1620) LDPC code used by the IEEE 802.11n standard. The post-processor can be integrated with a belief-propagation decoder with minimal overhead. The post-processor design is equally applicable to other structured LDPC codes.

This letter gives a random construction for Low Density Parity Check (LDPC) codes, which uses an iterative algorithm to avoid short cycles in the Tanner graph. The construction method has great flexible choice in LDPC code’s parameters including codelength, code rate, the least girth of the graph, the weight of column and row in the parity check matrix. The method can be applied to the irregular LDPC codes and strict regular LDPC codes. Systemic codes have many applications in digital communication, so this letter proposes a construction of the generator matrix of systemic LDPC codes from the parity check matrix. Simulations show that the method performs well with iterative decoding.

Low Density Parity Check (LDPC) codes have capacity-approaching performance over several channels of interest. In practice, for good block-error rate performance, the girth of the Tanner graph of an LDPC code needs to be as high as possible. In theory, to show that block-error rate approaches zero for increasing block-lengths, the girth of the Tanner graph sequence needs to tend to infinity with block-length. To meet these requirements, we construct sequences of large-girth irregular LDPC codes for a given degree-distribution pair (DDP) by applying a general node splitting algorithm on large girth graphs. The obtained Tanner graph meets the required DDP up to a suitable approximation. By optimizing the node-splitting method and using suitable large-girth graphs, we show code constructions with smaller block length for the same girth, when compared to previous constructions. Similar gains in block length are observed in the construction of sequences of large-girth protograph LDPC codes. Simulations, over a binary erasure channel, confirm the gains in block-error rate obtained by the large girth construction.

We present a method to construct low-density parity-check (LDPC) codes with low error floors on the binary symmetric channel. Codes are constructed so that their Tanner graphs are free of certain small trapping sets. These trapping sets are selected from the trapping set ontology for the Gallager A/B decoder. They are selected based on their relative harmfulness for a given decoding algorithm. We evaluate the relative harmfulness of different trapping sets for the sum-product algorithm by using the topological relations among them and by analyzing the decoding failures on one trapping set in the presence or absence of other trapping sets. We apply this method to construct structured LDPC codes. To facilitate the discussion, we give a new description of structured LDPC codes whose parity-check matrices are arrays of permutation matrices. This description uses Latin squares to define a set of permutation matrices that have disjoint support and to derive a simple necessary and sufficient condition for the Tanner graph of a code to be free of four cycles.

DOI: 10.1049/cp:20061337 ISBN: 0 86341 644 6 Location: Hangzhou, China Conference date: 6-9 Nov. 2006 Format: PDF The BER performance of presented quasi-cyclic (QC) low-density parity-check (LDPC) codes is not good as that of randomly constructed LDPC codes, while the lack of structure of randomly constructed LDPC codes implies serious disadvantages in terms of storing and accessing a large parity-check matrix. To solve the problems, this paper proposes a design of good quasi-cyclic (QC) low-density parity-check (LDPC) codes, the obtained algebraically structured codes have large minimum distances and good BER performance. The proposed design is based on index matrices, which determines the shifts of the circulant matrices of the sparse parity-check matrices. Compared with the presented design of QC LDPC codes, the designed QC LDPC codes are free from girth 4, sometimes free from girth 6, and have much larger minimum distances. Based on the algebraic code structure, the conditions of the girth and minimum distance of the codes are found. The BER performance of the designed QC LDPC block codes compares with that of randomly constructed LDPC codes for any block lengths. Better BER performance is obtained by increasing the circulant size of the base QC code. Simulations verify the construction of the QC LDPC codes to be valid. (4 pages) Inspec keywords: AWGN channels; error statistics; channel coding; algebraic codes; parity check codes; sparse matrices Subjects: Algebra; Other topics in statistics; Codes

Turbo codes are attractive compared with Low Density Parity Check (LDPC) codes for Forward Error Correction (FEC) applications mainly due to their superior performance, especially at low Signal-to-Noise Ratio (SNR) such as are common in Powerline channels. For example, IEEE 1901-FFT PHY used the Turbo coding scheme defined in the HomePlug AV standards. However, patent fees are usually required for each turbo-code enabled manufactured device. The objective of this paper is to examine whether unlicensed LDPC codes, with optimized choices of block lengths, could be a viable alternative for future Powerline Communications (PLC) applications. The paper shows that the performance of the LDPC codes can approximate that of the Turbo codes with higher block lengths, on channels with typical and realistic PLC characteristics. The paper also shows that the additional complexity associated with this increase in block length can be mitigated by the use of Quasi-Cyclic LDPC (QC-LDPC) codes.

Cages, defined as regular graphs with minimum number of nodes for a given girth, are well-studied in graph theory. Trapping sets are graphical structures responsible for error floor of low-density parity-check (LDPC) codes, and are well investigated in coding theory. In this paper, we make connections between cages and trapping sets. In particular, starting from a cage (or a modified cage), we construct a trapping set in multiple steps. Based on the connection between cages and trapping sets, we then use the available results in graph theory on cages and derive tight upper bounds on the size of the smallest trapping sets for variable-regular LDPC codes with a given variable degree and girth. The derived upper bounds in many cases meet the best known lower bounds and thus provide the actual size of the smallest trapping sets. Considering that nonzero codewords are a special case of trapping sets, we also derive tight upper bounds on the minimum weight of such codewords, i.e., the minimum distance, of variable-regular LDPC codes as a function of variable degree and girth.

In this paper, we present an algorithm to find all low-weight codewords in a given quasi-cyclic (QC) low-density parity-check (LDPC) code with a fixed column-weight and girth. The main idea is to view a low-weight codeword as an (a, 0) trapping sets, and then show that each topologically different (a, 0) trapping set can be dissected into smaller trapping sets. The proposed search method relies on the knowledge of possible topologies of such smaller trapping sets present in a code ensemble, which enables an efficient search. Combined with the high-rate QC LDPC code construction which successively adds blocks of permutation matrices, the algorithm ensures that in the code construction procedure all codewords up to a certain weight are avoided, which leads to a code with the desired minimum distance. The algorithm can be also used to determine the multiplicity of the low-weight codewords with different trapping set structure.

Block Markov superposition transmission of LDPC codes

Low-density Parity check codes (LDPC) are gaining interest for high data rate application in both terrestrial and spatial communications which requires low bit error rate. This paper proposes an algorithm through which the best parity check matrix is obtained for irregular low density parity check codes, which reduces the Bit Error Rate ,Frame Error Rate and computational complexity. Tanner graph also called a bipartite graph format in an Low Density Parity Check (LDPC) code design contains many short cycles; it will produce a computational complexity in a code design process and it degrades the code performance. To overcome this effect, we proposed an new algorithm which obtains a best final parity check matrix. Throughout the paper we will give the detailed description of an efficient algorithm proposed. The complexity is studied graphically and analytically. Using proposed algorithm, cycles of length four observed in corresponding matrix are removed. Each matrix is evaluated over a noisy Additive White Gaussian Noise (AWGN) channel. Bit Error rate and Frame error rate is calculated. The results are compared with randomly generated best parity check matrix. Simulation results shows that proposed method successfully overcomes the computational complexity and meets the near Shannon limit.

In this paper, we focus on the Generalized Belief Propagation (GBP) algorithm to solve trapping sets in Low-Density Parity-Check (LDPC) codes. Trapping sets are topological structures in Tanner graphs of LDPC codes that are not correctly decoded by Belief Propagation (BP), leading to exhibit an error-floor in the Bit-Error Rate (BER). Stemming from statistical physics of spin glasses, GBP consists in passing messages between clusters of Tanner graph nodes in another graph called the region-graph. Here, we introduce a specific clustering of nodes, based on a novel local loopfree principle, that breaks trapping sets such that the resulting region-graph is locally loopfree. We then construct a hybrid decoder made of BP and GBP that proves to be a powerful decoder as it clearly improves the BER and defeats the error-floor.

International audience

In this paper we propose an innovative channel coding scheme called 'Accumulate Repeat Accumulate codes' (ARA). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes, thus belief propagation can be used for iterative decoding of ARA codes on a graph. The structure of encoder for this class can be viewed as precoded Repeat Accumulate (RA) code or as precoded Irregular Repeat Accumulate (IRA) code, where simply an accumulator is chosen as a precoder. Thus ARA codes have simple, and very fast encoder structure when they representing LDPC codes. Based on density evolution for LDPC codes through some examples for ARA codes, we show that for maximum variable node degree 5 a minimum bit SNR as low as 0.08 dB from channel capacity for rate 1/2 can be achieved as the block size goes to infinity. Thus based on fixed low maximum variable node degree, its threshold outperforms not only the RA and IRA codes but also the best known LDPC codes with the dame maximum node degree. Furthermore by puncturing the accumulators any desired high rate codes close to code rate 1 can be obtained with thresholds that stay close to the channel capacity thresholds uniformly. Iterative decoding simulation results are provided. The ARA codes also have projected graph or protograph representation that allows for high speed decoder implementation.

Big data storage demands larger cluster. The increasing size of the cluster may lead to failures of larger number of nodes. To provide reliable big data storage, replications are not cost-effective and does not provide a robust solution to prevent data loss. Traditional erasure codes applied in the RAID system such as Reed-Solomon (R-S) based solutions have limitations in providing high reliability. This is because higher reliability requires erasure codes with larger size. The computational cost of the R-S codes increase quadratically with the number of failures the R-S codes can tolerate for the same redundancy rate. It has been shown that Low Density Parity Check (LDPC) codes have lower computational cost and repair network traffic compared with R-S based solutions. Unfortunately, there does not exist a construction method for LDPC codes with larger size to control the computational cost and repair traffic. In this paper, a novel method is proposed to construct a family of LDPC codes - expanCodes with expandable sizes. The proposed expanCodes allows the encoding and decoding complexity remain unchanged with the increase of the size of the LDPC codes. As a result, increased reliability can be achieved without additional computation and repair traffic. The proposed expanCodes is integrated with the Hadoop system. Simulations show that more than 29% decrease in terms of encoding and decoding latency compared with R-S based solutions.

This study focus on the performance analysis of Cooperative communication networks based on WiMAX Low Density Parity Check (LDPC) codes. The channel capacity approaching coding technique LDPC having coding gain method Bit Interleave Coded Modulation with Iterative Decoding (BICM-ID) is used. The different fading environment is analyze to counter the challenges in wireless communication and provides solutions for the drawbacks in the multiple input multiple output MIMO technology. The relays are used in Cooperative communications networks to increases the range and link reliability at a lower transmit power because once the signal transmit power loses its strength it’s amplify on the relay node and when it suffers from noise it is also decoded at the relay node which increases the link reliability. LDPC with iterative decoding are used to gain BER performance only a small amount of decibel to attain Shannon limit. This performance analysis open the way for WiMAX technology can be used with Cooperative networks by using LDPC codes. The above mention communication system will provides rate, range and reliability at a lower cost, less complexity and lower transmit power.