Efficient Post-Processors for Improving Error-Correcting Performance of LDPC Codes

Several combinatorial properties of low-density parity-check (LDPC) codes, such as minimum distance, diameter, stopping number, girth and cycle-length distribution of the corresponding Tanner graph, are known to influence their performance under iterative decoding. Recently, a new class of combinatorial configurations, termed trapping sets, was shown to be of significant importance in determining the properties of LDPC codes in the error-floor region. Very little is known both about the existence/parameters of trapping sets in structured LDPC codes and about possible techniques for reducing their negative influence on the code's performance. In this paper, we address both these problems from an algorithmic and combinatorial perspective. We first provide a numerical study of the trapping phenomena for the Margulis code, which exhibits a fairly high error-floor. Based on this analysis, conducted for two different implementations of iterative belief propagation, we propose a novel decoding process, termed averaged decoding. Averaged decoding provides for a significant reduction in the number of incorrectly decoded frames in the error-floor region of the Margulis code. Furthermore, based on the results of the algorithmic approach, we suggest a novel combinatorial characterizations of trapping sets in the class of LDPC codes based on finite geometries. Projective geometry LDPC codes are suspected to have extremely low error-floors, which is a property that we may attribute to the non-existence of certain small trapping sets in the code graph.

This letter gives a random construction for Low Density Parity Check (LDPC) codes, which uses an iterative algorithm to avoid short cycles in the Tanner graph. The construction method has great flexible choice in LDPC code’s parameters including codelength, code rate, the least girth of the graph, the weight of column and row in the parity check matrix. The method can be applied to the irregular LDPC codes and strict regular LDPC codes. Systemic codes have many applications in digital communication, so this letter proposes a construction of the generator matrix of systemic LDPC codes from the parity check matrix. Simulations show that the method performs well with iterative decoding.

<div> <h2>Abstract</h2> <p><strong>Objective:</strong> In the code theory, parallel concatenation of codes becomes more popular after the introduction of turbo codes. In recent years, the Low Density Parity Check (LDPC) code has found remarkable advancement and has seen them outshine turbo codes in terms of performance especially in the error floor and higher code rate. The main objective of this paper is to address the various techniques of a parallel concatenation of LDPC code in code theory. <strong>Method/Finding:</strong> To reduce the complexity of encoding and decoding for longer codes various parallel concatenation of LDPC coding methods were introduced and the performance was compared with other work. <strong>Novelty:</strong> When a longer block length is used, the parallel LDPC decoder is suffered from the complexity of prohibitive implementation. To overcome this issue and to achieve the best performance for longer codes, the different methods for parallel concatenation of LDPC codes were introduced with reduced complexity. This will helps to break the long and complex LDPC code into less complex and smaller LDPC to distribute the decoding and encoding load. Also, this will provides scalability and scope for improving the performance of LDPC codes in practical delay-sensitive and energy-aware applications.</p> <p><strong>Keywords:</strong> Parallel concatenation; LowDensity ParityCheck (LDPC); turbo codes; Parallel Concatenated Gallager Codes (PCGC)</p> </div> <div></div> <div> </div>

Low-density Parity check codes (LDPC) are gaining interest for high data rate application in both terrestrial and spatial communications which requires low bit error rate. This paper proposes an algorithm through which the best parity check matrix is obtained for irregular low density parity check codes, which reduces the Bit Error Rate ,Frame Error Rate and computational complexity. Tanner graph also called a bipartite graph format in an Low Density Parity Check (LDPC) code design contains many short cycles; it will produce a computational complexity in a code design process and it degrades the code performance. To overcome this effect, we proposed an new algorithm which obtains a best final parity check matrix. Throughout the paper we will give the detailed description of an efficient algorithm proposed. The complexity is studied graphically and analytically. Using proposed algorithm, cycles of length four observed in corresponding matrix are removed. Each matrix is evaluated over a noisy Additive White Gaussian Noise (AWGN) channel. Bit Error rate and Frame error rate is calculated. The results are compared with randomly generated best parity check matrix. Simulation results shows that proposed method successfully overcomes the computational complexity and meets the near Shannon limit.

Turbo codes are attractive compared with Low Density Parity Check (LDPC) codes for Forward Error Correction (FEC) applications mainly due to their superior performance, especially at low Signal-to-Noise Ratio (SNR) such as are common in Powerline channels. For example, IEEE 1901-FFT PHY used the Turbo coding scheme defined in the HomePlug AV standards. However, patent fees are usually required for each turbo-code enabled manufactured device. The objective of this paper is to examine whether unlicensed LDPC codes, with optimized choices of block lengths, could be a viable alternative for future Powerline Communications (PLC) applications. The paper shows that the performance of the LDPC codes can approximate that of the Turbo codes with higher block lengths, on channels with typical and realistic PLC characteristics. The paper also shows that the additional complexity associated with this increase in block length can be mitigated by the use of Quasi-Cyclic LDPC (QC-LDPC) codes.

RS (Reed - Solomon) code is used in DVB-H (digital video broadcasting - handheld) system as an addtional error correcting code to improve the performance during mobile reception. LDPC (low density parity check) code which is rediscovered recently shows the astonishing performance. Therefore LDPC code can be used to replace RS code in order to improve the performance further since both of them are block codes. So the performance of LDPC code in MPE-FEC (multi protocol encapsulation - forward error correction) frame of DVB-H system is analyzed in this paper.

Scheduling strategy is considered an important aspect of belief-propagation (BP) decoding of low-density parity-check (LDPC) codes because it affects the decoder's convergence rate, decoding complexity and error-correction performance. In this paper, we propose two new scheduling strategies for the BP decoding of non-binary LDPC (NB-LDPC) codes. Both the strategies are devised based on the concept of check node reliability and employ a heuristically defined threshold which can adapt to the communication channel variations. As the scheduling strategies only update a subset of the check nodes in each iteration, they result in reduced iteration cost. Furthermore, since the BP performs suboptimally for finite-length LDPC codes, especially for short-length LDPC codes, by enhancing the message propagation over the Tanner Graphs of short-length NB-LDPC codes, the new scheduling strategies can even improve the error-correction performances of BP decoding. Simulation results demonstrate that the new scheduling strategies provide good performance/complexity tradeoffs.

In this paper we propose an innovative channel coding scheme called 'Accumulate Repeat Accumulate codes' (ARA). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes, thus belief propagation can be used for iterative decoding of ARA codes on a graph. The structure of encoder for this class can be viewed as precoded Repeat Accumulate (RA) code or as precoded Irregular Repeat Accumulate (IRA) code, where simply an accumulator is chosen as a precoder. Thus ARA codes have simple, and very fast encoder structure when they representing LDPC codes. Based on density evolution for LDPC codes through some examples for ARA codes, we show that for maximum variable node degree 5 a minimum bit SNR as low as 0.08 dB from channel capacity for rate 1/2 can be achieved as the block size goes to infinity. Thus based on fixed low maximum variable node degree, its threshold outperforms not only the RA and IRA codes but also the best known LDPC codes with the dame maximum node degree. Furthermore by puncturing the accumulators any desired high rate codes close to code rate 1 can be obtained with thresholds that stay close to the channel capacity thresholds uniformly. Iterative decoding simulation results are provided. The ARA codes also have projected graph or protograph representation that allows for high speed decoder implementation.

Low Density Parity Check (LDPC) codes have capacity-approaching performance over several channels of interest. In practice, for good block-error rate performance, the girth of the Tanner graph of an LDPC code needs to be as high as possible. In theory, to show that block-error rate approaches zero for increasing block-lengths, the girth of the Tanner graph sequence needs to tend to infinity with block-length. To meet these requirements, we construct sequences of large-girth irregular LDPC codes for a given degree-distribution pair (DDP) by applying a general node splitting algorithm on large girth graphs. The obtained Tanner graph meets the required DDP up to a suitable approximation. By optimizing the node-splitting method and using suitable large-girth graphs, we show code constructions with smaller block length for the same girth, when compared to previous constructions. Similar gains in block length are observed in the construction of sequences of large-girth protograph LDPC codes. Simulations, over a binary erasure channel, confirm the gains in block-error rate obtained by the large girth construction.

Big data storage demands larger cluster. The increasing size of the cluster may lead to failures of larger number of nodes. To provide reliable big data storage, replications are not cost-effective and does not provide a robust solution to prevent data loss. Traditional erasure codes applied in the RAID system such as Reed-Solomon (R-S) based solutions have limitations in providing high reliability. This is because higher reliability requires erasure codes with larger size. The computational cost of the R-S codes increase quadratically with the number of failures the R-S codes can tolerate for the same redundancy rate. It has been shown that Low Density Parity Check (LDPC) codes have lower computational cost and repair network traffic compared with R-S based solutions. Unfortunately, there does not exist a construction method for LDPC codes with larger size to control the computational cost and repair traffic. In this paper, a novel method is proposed to construct a family of LDPC codes - expanCodes with expandable sizes. The proposed expanCodes allows the encoding and decoding complexity remain unchanged with the increase of the size of the LDPC codes. As a result, increased reliability can be achieved without additional computation and repair traffic. The proposed expanCodes is integrated with the Hadoop system. Simulations show that more than 29% decrease in terms of encoding and decoding latency compared with R-S based solutions.

DOI: 10.1049/cp:20061337 ISBN: 0 86341 644 6 Location: Hangzhou, China Conference date: 6-9 Nov. 2006 Format: PDF The BER performance of presented quasi-cyclic (QC) low-density parity-check (LDPC) codes is not good as that of randomly constructed LDPC codes, while the lack of structure of randomly constructed LDPC codes implies serious disadvantages in terms of storing and accessing a large parity-check matrix. To solve the problems, this paper proposes a design of good quasi-cyclic (QC) low-density parity-check (LDPC) codes, the obtained algebraically structured codes have large minimum distances and good BER performance. The proposed design is based on index matrices, which determines the shifts of the circulant matrices of the sparse parity-check matrices. Compared with the presented design of QC LDPC codes, the designed QC LDPC codes are free from girth 4, sometimes free from girth 6, and have much larger minimum distances. Based on the algebraic code structure, the conditions of the girth and minimum distance of the codes are found. The BER performance of the designed QC LDPC block codes compares with that of randomly constructed LDPC codes for any block lengths. Better BER performance is obtained by increasing the circulant size of the base QC code. Simulations verify the construction of the QC LDPC codes to be valid. (4 pages) Inspec keywords: AWGN channels; error statistics; channel coding; algebraic codes; parity check codes; sparse matrices Subjects: Algebra; Other topics in statistics; Codes

This study focus on the performance analysis of Cooperative communication networks based on WiMAX Low Density Parity Check (LDPC) codes. The channel capacity approaching coding technique LDPC having coding gain method Bit Interleave Coded Modulation with Iterative Decoding (BICM-ID) is used. The different fading environment is analyze to counter the challenges in wireless communication and provides solutions for the drawbacks in the multiple input multiple output MIMO technology. The relays are used in Cooperative communications networks to increases the range and link reliability at a lower transmit power because once the signal transmit power loses its strength it’s amplify on the relay node and when it suffers from noise it is also decoded at the relay node which increases the link reliability. LDPC with iterative decoding are used to gain BER performance only a small amount of decibel to attain Shannon limit. This performance analysis open the way for WiMAX technology can be used with Cooperative networks by using LDPC codes. The above mention communication system will provides rate, range and reliability at a lower cost, less complexity and lower transmit power.

We propose a novel concatenated coding scheme combined Low Density Parity Check(LDPC) code and vertical Bell Labs layered space-time (VBLAST) code to improve the bit error rate (BER) performance for Free-space optical (FSO) communication links with On Off Keying(OOK) modulation. In the scheme, π-rotation encoding and belief-propagation (BP) decoding algorithm are employed in LDPC code, and minimum mean-square error (MMSE) soft-decision decoding algorithm is used for VBLAST code. Moreover, a joint iterative detection and decoding algorithm of VBLAST code and LDPC code is used to improve the overall link performance. At last, the BER of the proposed scheme over lognormal atmospheric turbulent fading channels is analyzed by using Monte Carlo method. The result shows that the BER of the proposed concatenated coding scheme is much improved than that only use VBLAST code scheme.

Decoding by alternating direction method of multipliers (ADMM) is a promising linear programming decoder for low-density parity-check (LDPC) codes. In this paper, we propose a two-step scheme to lower the error floor of LDPC codes with ADMM penalized decoder. For the undetected errors that cannot be avoided at the decoder side, we modify the code structure slightly to eliminate low-weight code words. For the detected errors induced by small error-prone structures, we propose a post-processing method for the ADMM penalized decoder. Simulation results show that the error floor can be reduced significantly over three illustrated LDPC codes by the proposed two-step scheme.

For ultra-reliable low-latency communications (URLLC), low error floors are required for channel codes. In this paper, we propose a method of adding some edges to the protograph of the protograph-based raptor-like (PBRL) low-density parity-check (LDPC) codes. The added edges play a role of boosting up the reliability of weak variable nodes so that the code with edge addition can achieve low error floors. The edge addition is applied to an instance of 5G new radio (NR) LDPC code and it is shown that the edge addition lowers the error floor of the 5G NR LDPC code. Since the edge addition does not change the existing edge connections in the protograph, an adaptive use with/without edge addition have an effect of implementing two PBRL LDPC codes for enhanced mobile broadband (eMBB) and URLLC in an efficient way while keeping the system compatible with the original PBRL LDPC code.