Analysis about MIMO Detection Algorithms

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

Multiple input multiple output (MIMO) technology has evolved over the past few years into a technology with great potential to drive the direction of future wireless communications. MIMO technology has become a solid reality when massive MIMO systems (MIMO with large number of antennas and transceivers) were commercially deployed in several countries across the world in the recent past. Moreover, MIMO has been integrated into state-of-the-art paradigms such as fifth-generation (5G) networks as one of the main enabling technologies. MIMO possesses many attractive and highly desirable properties such as spatial multiplexing, diversity gains, and adaptive beamforming gains that leads to high data rates, enhanced reliability, and other enhancements. Nevertheless, beyond 5G technologies demand wireless communication systems with, among other properties, immensely higher data rates and better reliability simultaneously at the same time. In this work, a new, novel MIMO technique for simultaneously achieving multiplexing and diversity gains as well as completely eliminating any processing at the MIMO receiver, leading to advantages such as low complexity and low power consumption, is proposed. The proposed technique employs the design of interference-canceling matrices, which are calculated from the channels between the transceiver antennas, where the matrices are employed at the base station to help achieve multiplexing and diversity gains simultaneously. The novelty and efficiency of the introduced paradigm is demonstrated via mathematical models and validated by Monte Carlo simulations. Results indicate that the proposed system outperforms conventional MIMO models.

Since H. Yao proposed the lattice reduction (LR)-aided detection algorithm for the MIMO detector, one can exploit the diversity gain provided by the LR method to achieve performance comparable to the maximum likelihood (ML) algorithm but with complexity close to the simple linear detection algorithms such as zero forcing (ZF), minimum mean squared error, and successive interference cancellation, etc. In this paper, in order to reduce the processing time of the LR-aided detector, a graphics processing unit (GPU) has been proposed as the main modem processor in such a way that the detections can be performed in parallel using multiple threads in the GPU. A 2X2 multiple input multiple output (MIMO) WiMAX system has been implemented using a GPU to verify that various MIMO detection algorithms such as ZF, ML, and LR-aided methods can be processed in real-time. From the experimental results, we show that GPUs can realize a 2X2 WiMAX MIMO system adopting an LR-aided detector in real-time. We achieve a processing time of 2.75 ms which meets the downlink duration specification of 3 ms. BER performance of experimental tests also indicates that the LR-aided MIMO detector can fully exploit diversity gain as well as ML detector.

Multiple-Input Multiple-Output (MIMO) technologies utilize multiple antennas at the transceivers and enable enhanced diversity or multiplexing gain. The first implementations of MIMO technology appeared in cellular communication and Wi-Fi systems. One of the main problems with early MIMO systems is their limited performance in meeting the requirements of next generation communication systems. Specifically, the parameters like peak data rates, spectrum efficiency and energy efficiency constraints cannot be met with existing MIMO architectures. Hence, early MIMO techniques evolved to massive MIMO (mMIMO) type of communication as the number of antennas at both transmitters and receivers increased. Included in 5G New Radio standard, mMIMO enabled an increase the spectral efficiency and coverage compared with earlier MIMO techniques. Nowadays, there exists an ever-increasing interest in the application of advanced MIMO technologies in 6G networks. These applications include ultra massive MIMO (mMIMO), holographic MIMO and intelligent reflecting surface (IRS) assisted MIMO. These new advanced MIMO techniques either employ larger number of antennas or extremely large aperture arrays compared with mMIMO and are named as extremely large-scale MIMO. This paper presents a detailed overview of all these techniques. Joint design of wireless communication and radar sensing, named as integrated sensing and communication (ISAC) as well, has shown to improve spectrum efficiency and reduce power consumption. Recent novel research on ISAC exploits the application of MIMO technology specifically in joint communication and radar sensing (JCS) systems. In this aspect, the other objective of this work is to exploit MIMO communication and MIMO radar coexistence. After summarizing the current state of the art on MIMO radar systems, this paper exploits joint application of advanced MIMO communication and radar sensing. Finally, it aims to offer a perspective on future research directions and the potential of overall MIMO systems discussed in the paper.

In conventional ways of fast responding and high performing model predictive control using Field Programmable Gate Arrays (FPGA), the approaches developed are applicable only to Single Input Single Output System (SISO). Many real time systems are Multiple Input Multiple Output (MIMO) systems and loop interaction is a major concern and has to be reduced in control of MIMO systems. Also, direct digital control with ability to solve the Quadratic Programming (QP) problem online, which can be applied to complex systems with fast response time and/or embedded applications and with limited computational resource for supervisory control approach, is required in many complex industrial MIMO systems. A novel direct digital control of Model predictive controller with FPGA for a MIMO system which considers and reduces loop interaction and which can also be implemented with very less investment is proposed here. The system was modeled from first principles and then simulated in Labview environment for MIMO system. Implementation of the system and response was verified for a stirred tank system. The proposed system has good performance in terms of reduction in loop interaction which is a major concern in implementation of controller for MIMO systems. Also, direct digital control of MIMO system instead of supervisory control was accomplished.

The free space optical (FSO) communication system has attracted many researchers from different countries, owning to its advantages such as high security, high speed and anti-interference. Among all kinds of the channels of the FSO communication system, the atmosphere channel is very difficult to deal with for two typical disadvantages at least. The one is the scintillation of the optical carrier intensity caused by the atmosphere turbulence and the other is the multipath effect by the optical scattering. A lot of studies have shown that the MIMO (Multiple Input Multiple Output) technology can overcome the scintillation of the optical carrier through the atmosphere effectively. So the background of this paper is a MIMO system which includes multiple optical transmitting antennas and multiple optical receiving antennas. A number of particles such as hazes, water droplets and aerosols exit in the atmosphere widely. When optical carrier meets these particles, the scattering phenomenon is inevitable, which leads to the multipath effect. As a result, a optical pulse transmitted by the optical transmitter becomes wider, to some extent, when it gets to the optical receiver due to the multipath effect. If the information transmission rate is quite low, there is less relationship between the multipath effect and the bit error rate (BER) of the communication system. Once the information transmission rate increases to a high level, the multipath effect will produce the problem called inter symbol inference (ISI) seriously and the bit error rate will increase severely. In order to take the advantage of the FSO communication system, the inter symbol inference problem must be solved. So it is necessary to use the channel equalization technology. This paper aims at deciding a equalizer and designing suitable equalization algorithm for a MIMO free space optical communication system to overcome the serious problem of bit error rate. The reliability and the efficiency of communication are two important indexes. For a MIMO communication system, there are two typical equalization methods. The first method, every receiving antenna has an independent equalizer without the information derived from the other receiving antennas. The second, the information derived from all of the receiving antennas mixes with each other, according to some definite rules, which is called space-time equalization. The former is discussed in this paper. The equalization algorithm concludes training mode and non training mode. The training mode needs training codes transmitted by the transmitter during the whole communication process and this mode reduces the communication efficiency more or less. In order to improve the communication efficiency, the blind equalization algorithm, a non training mode, is used to solve the parameter of the equalizer. In this paper, firstly, the atmosphere channel is described focusing on the scintillation and multipath effect of the optical carrier. Then, the structure of a equalizer of MIMO free space optical communication system is introduced. In the next part of this paper, the principle of the blind equalization algorithm is introduced. In addition, the simulation results are showed. In the end of this paper, the conclusions and the future work are discussed.

Multiple Input Multiple Output (MIMO) low complexity receiver which utilizes the compressive sensing detection for Spatial Modulation in large scale MIMO system in order to reduce the system complexity. In conventional MIMO system; huge amount of antennas is used at both ends to exploit the multipath propagation. This system maximizes the throughput performance and data rates are increased but only at the cost of high hardware complexity and increased power-consumption. Spatial Modulation Matching Pursuit (SMMP) is the proposed enhanced CS technique used for the improvement of detection performance. Hence, this paper reviews recent research findings concerning normalized Compressive Sensing (CS) detection algorithm, used for Spatial Modulation (SM) in massive MIMO, to lowers the signal processing complexity, which in result improves the energy efficiency of system against that of conventional MIMO system.This strategy is achieved by involving additional structures and sparsity in which a single transmitter antenna or a subset of it is turned on at each case to transmit a certain data. The subset of antenna which is turned on for transmission depends on approaching data bits. Therefore, the total increase in the spectral efficiency of the system is given as base-two logarithm of whole antennas at the transmitter. It reduces the signal processing load at base station and doesn’t depend upon any synchronization between transmitters. The Spatial Modulation Matching Pursuit used prevents the Inter Channel Interference (ICI) of the system which in result improves the Bit Error Rate (BER) performance than the typical MIMO system.

Consider a multiple input multiple output (MIMO) system with pulse amplitude modulation (PAM), where each transmit antenna is allowed to choose a different transmission delay. (We refer to this system as a MIMO system with asynchronous PAM.) Such MIMO systems have been studied before for increasing diversity and avoiding unintentional beamforming. We quantify the capacity/outage capacity improvement due to asynchronism and the corresponding spectral leakage (if any) for MIMO point-to-point and MIMO broadcast channels. We show that under commonly used transmitter spectral mask constraints, the channel has unbounded degrees of freedom. Synchronous PAM exploits only a finite number of these degrees of freedom, and asynchronism helps to improve capacity. For most cases of interest, two distinct shifts attain most of the capacity improvement. These gains are robust to interference from adjacent carriers. Analysis of the spectrum of the asynchronous PAM suggests that optimal water-filling based schemes are useful for improving capacity only in directional links due to possible spectral leakage, while uniform power allocation leads to capacity improvement without any extra spectral leakage.

A near maximum likelihood performance modified firefly algorithm for large MIMO detection

The research of closed form expressions for the pdf of the lth ordered eigenvalue of a Wishart matrix has received a great attention in the past years owing to its applications in the performance analysis of multiple input multiple output (MIMO) systems in fading environments. Although several closed form expressions for this pdf were obtained in the past years, to the authors' knowledge, no one was very friendly for further analysis. We propose a methodology to obtain the pdf for the lth largest eigenvalue whose expression is given as a sum of terms xβe-xδ. This expression is easily usable to obtain closed form results for the performance of many MIMO systems, such as, for instance, MIMO beamforming, and MIMO with Singular Value Decomposition (SVD). The methodology is valid for both uncorrelated and correlated central Wishart, allowing the investigation of MIMO systems with uncorrelated and correlated Rayleigh fading. © 2008 IEEE.

Model reference robust control (MRRC) is derived for MIMO systems that have a right Hermite normal form which is SPR and diagonal, and then for systems whose right Hermite normal form is diagonal but not SPR. It is shown that MRRC of multiple input multiple output (MIMO) systems is an extension of model reference control (MRC) of MIMO systems and MRRC of SISO systems. Unwanted coupling exists in many physical MIMO systems. The recursive backstepping procedure used in non-SPR SISO systems cannot be directly applied to diagonal MIMO non-SPR systems without the introduction of the augmented matrix or a precompensator. It is shown that MRRC decouples MIMO systems using only input and output measurements rather than state feedback.

In statistical signal processing, the sequential Monte Carlo (SMC) method is powerful and can approach the theoretical optima. However, its computational complexity is usually very high, especially in multiple-input multiple-output (MIMO) systems. This paper presents a new low-complexity SMC (LC-SMC) algorithm for blind detection in MIMO systems, the main idea of which is to shrink the sampling space via channel estimation which is initialized using the first differentially modulated symbol and then updated using the Monte Carlo samples. Since the a posteriori probability of the transmitted symbols can be calculated separately by each transmit antenna, the proposed LC-SMC algorithm is not only computationally efficient, as compared to the original SMC whose complexity grows exponentially with the number of transmit antennas, but also makes blind turbo receiver more feasible for multilevel/phase modulations. Simulation results are presented to demonstrate the effectiveness of the LC-SMC algorithm

After a few decades’ evolution of wireless communication systems, to ensure reliable highspeed communication over unreliable wireless channels is still one of the major challenges facing researchers and engineers. The use of multiple antennas at transmitter and receiver, known as multiple-input multiple-output (MIMO) communications, is one promising technology delivering desired wireless services. The main goal of this thesis is to study two important issues in wireless MIMO communication systems: receiver design for coded MIMO systems, and diversity-multiplexing tradeoff analysis in general fading channels. In the first part of this thesis, we decompose the receiver design problem into two subproblems: MIMO channel estimation and MIMO detection. For the MIMO channel estimation, we develop an expectation-maximization (EM) based semi-blind channel and noise covariance matrix estimation algorithm for space-time coding systems under spatially correlated noise. By incorporating the proposed channel estimator into the iterative receiver structure, both the channel estimation and the error-control decoding are improved significantly. We also derive the modified Cramer-Rao bounds (MCRB) for the unknown parameters as the channel estimation performance metric, and demonstrate that the proposed channel estimation algorithm can achieve the MCRB after several iterations. For the MIMO detection, we propose a novel lowcomplexity MIMO detection algorithm, which has only cubic order computational complexity, but with near-optimal performance. For a 4×4 turbo-coded system, we show that the proposed detector had the same performance as the maximum a posteriori (MAP) detector for BPSK modulation, and 0.1 dB advantage over the approximated MAP detector (list sphere decoding algorithm) for 16-QAM modulation at BER = 10−4. In the second part of this thesis, we derive the optimal diversity-multiplexing tradeoff for

Wireless Sensor Network (WSN) is used in various applications. Sensors acquire samples of physical data and send them to a central node in different topologies to process the data and makes decisions. A main performance factor for WSN is the battery life that depends on energy consumption on the sensor. To reduce the energy consumption, an energy efficient transmission technique is required. Multiple Input Multiple Output (MIMO) systems showed good utilization of channel characteristics. This leads to enhance the transmission and hence reduce energy consumed by the sensor. In MIMO systems multiple signals are combined at the transmitter and transmitted using multiple antennas. This provides each receiver the whole combined signal and hence, array processing techniques helps in getting better performance. To further enhance the transmission of data, a Low Density Parity Check (LDPC) Coded MIMO wireless sensor network is proposed. The system implements space diversity through Multiple Antennas and temporal diversity through LDPC code and uses a clustering procedure to optimize the forming of the MIMO system. Results showed that, if the number of sensors is greater than the number of receiving antennas, time or frequency multiplexing is possible to keep good performance for the devised system. And by controlling the encoder we can create a temporal and spatial code among the transmitted signals enhancing the BER results in longer battery life at sensor nodes.

An efficient multiple-input multiple-output (MIMO) detection (MD) algorithm includes novel, low-complexity, near-optimal and robust scheme is proposed in wireless communications when imperfect nois...