Combined light and electron microscope in routine histopathology.

IntroductionCurrently, the resolution of structural detail in conventional transmission electron microscopy (CTEM) of organic materials is limited by the electron beam damage suffered by the sample. It has recently been shown that the imaging modes now available in scanning transmission electron microscopy (STEM) provide the potential for improvements in resolution over CTEM methods. However, the effect of the sensitivity of an organic sample itself to beam damage has not been compared in STEM versus CTEM. In STEM each element of the sample area is briefly illuminated with a small diameter, high flux, scanning electron beam, whereas in CTEM the entire sample area is continuously illuminated with a large diameter, lower flux, static electron beam. Although it has been shown that the amount of sample damage in CTEM is independent of dose rate(2), the electron flux in STEM may range from 3 to 4 orders of magnitude greater than that in CTEM, with a possible influence on damage rate. Generally, the effects of beam size, high flux, and short dwell time of the scanning electron beam on sensitivity of the sample to damage in STEM are not known.

Adult channel catfish were exposed to 0 or 15 ppm arsenic as sodium arsenate in synthetic lake water for approximately six months. After sacrifice, livers were removed and examined by conventional transmission electron microscopy, optical microscopy, scanning electron microscopy, and electron probe X-ray microanalysis. Cytoplasmic structures in the nuclei were found to contain highly concentrated deposits of iron. Thirty percent of these structures were also found to contain arsenic at a level above the minimum detectable level for the conditions of the study. The size, shape and relative position of the cytoplasmic structures were the same as the hemosiderin granules observed by conventional transmission electron microscopy. (JMT)

In many fields of research in science, engineering, and medicine, electron microscopy as a method for directly imaging submicroscopic structures has become increasingly important in recent decades. Electron microscopy (EM) includes several different techniques: conventional transmission electron microscopy (TEM), high-resolution electron microscopy (HREM), highvoltage electron microscopy (HVEM), scanning electron microscopy (SEM), analytical electron microscopy (AEM), emission electron microscopy (EEM), and others. In the past the central aim of using electron microscopy was structure determination, but recently it has been of growing importance for also investigating different processes, i.e., changes in materials by interaction with several influential factors (e.g., heat, electric or mechanic fields, mechanical loading). Of particular interest is the study of the micromechanical processes of deformation and fracture. Therefore, electron microscopy is a very powerful tool for materials science. The present review reports on some capabilities and limitation of the application of electron microscopy to solid polymers. In Section II the techniques of electron microscopy are briefly reviewed, followed by a section that describes the main methods of specimen preparation of solid polymeric materials. In Section IV the results of several applications of electron microscopy are discussed to reveal the morphology as well as the micromechanical deformation processes of several polymeric materials.

The energy filtered imaging technique has so far been carried out in a scanning transmission electron microscope (STEM) fitted with a sector type energy analyzer. The STEM has a disadvantage of low beam parallelity because it uses a convergent beam, while the conventional transmission electron microscope (CTEM) allows good phase contrast and diffraction contrast to be obtained because of the high parallelity of the beam, and allows also high resolution images to be obtained. The technique to obtain energy filtered CTEM images has thus far been carried out by a Castaing-Henry type filter or an Ω type filter. However, these filters have the disadvantage of lower energy resolution than conventional sector type energy analyzer at the present time. This paper reports energy filtered CTEM images of MgO smoke, obtained using a new scanning CTEM image technique and a high energy resolution sector type energy analyzer which can resolve bulk and surface plasmon energy.

High density lipoproteins of d = 1.12 to 1.21 g/ml from human serum (HDL3) were studied by electron microscopy with both negative staining and freeze-etching techniques. For the negatively stained specimens, a modified conventional transmission electron microscope as well as a scanning transmission electron microscope were used. The freeze-etched specimens were examined by a conventional transmission electron microscope. The diameter of HDL3 was found to be 105 +/- 4 A by freeze-etching and 94 +/- 6 A by negative staining. The surface of the HDL3 particles exhibited about 12 discrete domains, 28 +/- 3 A (freeze-etched) and 28 +/- 4 A (negatively stained) in diameter, of undefined chemical composition. Moreover, the freeze-etched specimens revealed an inner core 40 +/- 2 A in diameter, corresponding to estimated values reported previously. All information is consistent with the HDL3 model proposed by B. W. Shen, F. J. Kézdy, and A. M. Scanu [(1977) Proc. Natl. Acad. Sci. USA 74, 837-841], with additional evidence for well-defined surface substructure. The consistency of the images obtained with the various electron microscopy techniques and the marked change in the appearance of the surface in the HDL3 preparations that were digested by phospholipase A2 (EC 3.1.1.4) support the validity of the interpretation.

The microstructural and morphological properties of the as-prepared tin (Sn) coating on ferrous substrates affects the lifetime as well as the applicability of the coating itself. In order to improve our knowledge of this system, strips of steel St-37 were coated with Sn in the form of gas-atomized powder, with an average diameter of 110±10 μm, using plasma spraying. The plasma gas was an Ar-He mixture and the current intensity was 650 A. The as-casted coating was characterized with scanning electron microscopy (SEM), X-ray diffraction (XRD) and conventional transmission electron microscopy (CTEM). It was deduced that the coating is characterized by high integrity, although certain pores were detected far from the Fe-Sn interface. However they refer to less than 1% of the total volume. Nevertheless the examination with SEM and XRD proved that the coating is mainly composed of pure Sn. However, interdiffusion takes place between the two phases (Fe-Sn) at their interface as deduced by CTEM. As a result, certain Fe-Sn phases are formed, which seem to be scattered in the coating close to the interface in the form of small inclusions.

The installation of an imaging energy filter extends the imaging and analytical capabilities of a conventional transmission electron microscope (CTEM) considerably. We report here on experiments which demonstrate the versatility of such a device. The arrangement of our system is shown in Fig. 1. The experiments performed pertain to:The improvement of contrast in thick specimens by exclusion of inelastically scattered electrons. The spatial resolution of the electron microscope can be preserved by the correction of second-order aberrations with additional electromagnetic hexapoles.The determination of the concentration of light elements with EELS at a spatial resolution better than 10 nm. The chemical structure of ceramic material (SI3N4and SiC with additions) could thus be elucidated. A study on the extended fine structure in the energy loss spectra of the oxygen and magnesium K edges in MgO (Fig. 2) did confirm the theoretical prediction for that material.

The effects of parenteral injection of aluminum, indium, gadolinium, or terbium in rats have been previously studied in several organs such as the liver, the kidneys, etc., but never in mammary glands. In this work, we have attempted to study the subcellular localization of these elements after their intraperitoneal administration. Their subsequent effects in the lactating mammary gland cells have also been studied. Our results using conventional transmission electron microscopy have shown that the lysosomes of the mammary glandular epithelial cells are the intracellular site of accumulation of the studied elements. Our results have also show intracellular deteriorations such as an expanded ergastoplasm and altered mitochondria after intraperitoneal injection of aluminum and indium.

Multicolored gene reporters for light microscopy are indispensable for biomedical research, but equivalent genetic tools for electron microscopy (EM) are still rare despite the increasing importance of nanometer resolution for reverse engineering of molecular machinery and reliable mapping of cellular circuits. We here introduce the fully genetic encapsulin/cargo system of Quasibacillus thermotolerans (Qt), which in combination with the recently characterized encapsulin system from Myxococcus xanthus (Mx) enables multiplexed gene reporter imaging via conventional transmission electron microscopy (TEM) in mammalian cells. Cryo-electron reconstructions revealed that the Qt encapsulin shell self-assembles to nanospheres with T = 4 icosahedral symmetry and a diameter of ∼43 nm harboring two putative pore regions at the 5-fold and 3-fold axes. We also found that upon heterologous expression in mammalian cells, the native cargo is autotargeted to the inner surface of the shell and exhibits ferroxidase activity leading to efficient intraluminal iron biomineralization, which enhances cellular TEM contrast. We furthermore demonstrate that the two differently sized encapsulins of Qt and Mx do not intermix and can be robustly differentiated by conventional TEM via a deep learning classifier to enable automated multiplexed EM gene reporter imaging.

In 1967, Coates discovered the electron channelling contrast of backscattered electrons (BSEs) in scanning electron microscopy, and by this the possibility to investigate arrangements of lattice defects in deformed microstructures of materials. Since that time, a straightforward development of the scanning electron microscopes as well as of the electron channelling contrast technique took place. Nowadays, the performance of scanning electron microscopes is high enough that the resolution of electron channelling contrast imaging (ECCI) micrographs is comparable with conventional bright field transmission electron microscopy (TEM) micrographs. In the first part of the present paper, a historical review on the development of the ECCI technique starting from its discovery more than 45 years ago up to the combination with other advanced methods of scanning electron microscopy like electron backscatter diffraction or high-resolution selected area channelling patterning in the last few years is given. Major important investigations using this technique for the visualization of individual lattice defects like stacking faults (SFs) and dislocations or dislocation arrangements are chronologically summarized. The second part demonstrates that nowadays, ECCI micrographs taken in high-resolution scanning electron microscopes can be called high-resolution ECCI (HR-ECCI). It is shown that the resolution of individual SFs and dislocations in the HR-ECCI micrographs is comparable to that of conventional TEM (about 15 nm defect image width). Furthermore, the paper is demonstrating that HR-ECCI micrographs can be obtained for various types of materials after different mechanical loadings and different grain sizes ranging from large grain size of 500 μm (cast steel) down to less than 2 μm (γ-TiAl).

Chaffey, N.J. ed. Wood formation in trees--cell and molecular biology techniques

Crystalline structures of carbon complexes in amorphous carbon films

It is well known that the combination of a field emission gun (FEG) and a conventional transmission electron microscope (CTEM) is extremely important for nanometer area analysis in analytical electron microscopy. However, the smaller illumination angle and reduced energy spread of FEG than those of a conventional electron gun (W hair pin filament or LaB6) give a slowly damping envelop function in phase contrast transfer function (PCTF). Thus the FEG ensures application not only to analytical microscopy but also to high resolution electron microscopy to improve the information limit.In a high voltage electron microscope (above 200 kV), high-speed vacuum pumps have to be provided below the acceleration tube to get an ultra high vacuum (UHV) around the field emission tip located at the top of the acceleration tube. However, this method is not always the best way to provide UHV because of the poor vacuum conductance caused by the electrodes inside the acceleration tube.

Fine structure of abnormal filaments isolated from Alzheimer's diseased brain: an application of atomic force microscopy

Stereology is the method of choice for the quantitative assessment of biological objects in microscopy. It takes into account the fact that, in traditional microscopy such as conventional light and transmission electron microscopy, although one has to rely on measurements on nearly two-dimensional sections from fixed and embedded tissue samples, the quantitative data obtained by these measurements should characterize the real three-dimensional properties of the biological objects and not just their “flatland” appearance on the sections. Thus, three-dimensionality is a built-in property of stereological sampling and measurement tools. Stereology is, therefore, perfectly suited to be combined with 3D imaging techniques which cover a wide range of complementary sample sizes and resolutions, e.g. micro-computed tomography, confocal microscopy and volume electron microscopy. Here, we review those stereological principles that are of particular relevance for 3D imaging and provide an overview of applications of 3D imaging-based stereology to the lung in health and disease. The symbiosis of stereology and 3D imaging thus provides the unique opportunity for unbiased and comprehensive quantitative characterization of the three-dimensional architecture of the lung from macro to nano scale.