Crosstalk Noise of Octagonal TSV Array Arrangement Based on Different Input Signal

Through silicon vias (TSVs) play an important role as the vertical electrical connections in 3-D stacked integrated circuits. However, the closely clustered TSVs suffer from the crosstalk noise between the neighboring TSVs, and result in the extra delay and the deterioration of signal integrity. For a 3 × 3 TSV array, the severity of crosstalk noise in the center victim TSV is classified into 11 levels, which is defined as 0C to 10C from low noise to high noise, depending on the combinations of the digital patterns applied to the TSV array. An enhanced code based on the Fibonacci number system (FNS) to suppress the crosstalk noise below 6C level is proposed, in which both the redundancy of numbers and the nonuniqueness of Fibonacci-based binary codeword are utilized to search the proper codeword. Experimental results show that the proposed technique decreases about 22% latency of TSVs comparing with the worst crosstalk cases. This technique is applicable in the large-scale TSV array for it has a quasi-linear hardware overhead, and its system overhead is less than that of the 3-D 4-LAT counterpart if the data width is greater than 18, and it has good usability for it consumes less power per TSV and achieves lower bit error rate at the interested frequency range comparing with that of the original FNS coding technique.

Thermal conduction and mechanical strength around TSV (Through Silicon Via) structures of 3D SiP (Three Dimensional System in Package) were discussed both cases of with and without void in TSV by using a large scale simulator based on FEM, ADVENTURECluster® for ensuring the reliability of 3D SiP. In the results, the thermal performance that was required in 3D SiP was estimated to ensure the reliability. Simulations for thermal stresses around TSV structure in 3D SiP under thermal cycle condition due to power ON/OFF were carried out. In case that void was not in TSV, stresses in TSV were close to hydrostatic pressure and the magnitude of the equivalent stress was lower than the yield stress of copper. However, the level of the stresses, especially in Si chips, should not be negligible in inducing damages to TSVs and Si single crystals. In case that void was in TSV, stress was concentrated around void in TSV and the magnitude of the equivalent stress was lower than the yield stress of copper. The level of stresses applied to Si chip was slightly reduced due to void in TSV. However, its level should not be negligible in inducing damages to TSVs and Si single crystals.

Recently, the downsizing and high-performing semiconductor packages have been developed and 3D packaging has been spurred research into reliability of TSV (through silicon via) [l]-[9]. In conventional SiP (System in Package), several semiconductor chips had been arranged in a plate. It is difficult to correspond to downsizing and high-performing of electronic devices because that large area is occupied by the package. The semiconductor chips have been stacked and TSVs have been used to communicate between the chips in order to solve above problems. The 3D stacked structure which was developed by ASET (Association of Su per-Advanced Electronics Technologies) [10] is shown in Fig.1. TSV (copper) is electrode which passes through silicon chip and micro bump (copper) [11] is arranged between chips. Heat is generated in package due to operation of semiconductor device, and it has been reported that silicon is broken by thermal stress which is depend on temperature increment. In case of 3D-SIP, higher stress has to be considered in the most outer part of TSV and micro bump structure due to warp and mismatch of CTE (coefficient of thermal expansion) of material. Therefore simulations with detail model must be desired for more accurate evaluation of stresses in Si chips and TSVs. However it is difficult that all of TSVs and micro bumps in chips were modeled due to large number of numerical data even if the latest computing systems have been adopted.

In the present study, high density TSV structures have been designed and fabricated with different diameter and depths, ranging from 2 to 60 µm and 50 to 100 µm respectively. The ratios of TSV diameter to space between TSVs are 1∶2, 1∶3 and 1∶4. Inspection of TSV structures at each processing step is very crucial to proceed to next step. 3D X-ray CT scan analysis has been employed to inspect TSV wafers at different processing steps. Detailed 3D X-ray CT scan analysis has been carried out on 20, 50 and 60 um TSV array structures. Using this method, it is possible to observe defect shape, size and distribution by conducting the virtual cross-section at desired location. Based on the detailed online failure analysis, TSV process development parameter are being fine-tuned and optimized.

Thermal conduction and mechanical stresses in through silicon via (TSV) structures in three dimensional system in package (3D SiP) under device operation condition were discussed. A large scale simulator, ADVENTURECluster® based on finite element method (FEM) was used to simulate the effects of voids formed inside Cu TSVs on the thermal conduction and mechanical stresses in the TSV structure. The thermal performance that was required in 3D SiP was estimated to ensure the reliability. Simulations for thermal stresses in the TSV structure in 3D SiP were carried out under thermal condition due to power ON/OFF of device. In case that void was not present inside the TSV, the stresses in TSV were close to the hydrostatic pressure and the magnitude of the equivalent stress was lower than the yield stress of copper. Maximum principal stress of the Si chip in the TSV structure for the case without voids was lower than that of the bending strength of silicon. However, the level of the stresses in the Si chips should not be negligible for damages to Si chips. In case that void was present inside the TSV, stress concentration was occurred around the void in the TSV. The magnitude of the equivalent stress in the TSV was lower than the yield stress of copper. The magnitude of the maximum principal stress of the Si chip was lower than that of the bending strength of silicon. However, its level should not be negligible for damages to TSVs and Si chips. The stress on inner surfaces of Si chip was slightly reduced due to the presence of a void in the TSV.

The thermal and spatial variation of Cu through silicon via (TSV)-induced stress in 300 mm Si wafers has been investigated for both isolated TSVs and TSV arrays using top-down and cross-sectional spectral microRaman imaging. The TSV-induced stress in Si results from plastic yield of the Cu, is compressive in the immediate vicinity of the TSV, and transitions to a tensile state at larger separations - in quantitative agreement with finite element modeling (FEM). TSV arrays (linear and square) lead to substantial tensile stress enhancement within the array. Moreover, thermal annealing showed that the intra-array Si stress field became more compressive with increased post-CMP thermal annealing while the Si stress-field external to the arrays exhibited little change. This may open potential avenues for reduction of TSV-induced Si stress in 3DICs.

Through Silicon Via (TSV) technology has been a preferred and promising strategy to achieve the reliable interconnection for the integration of 3D IC. The temperature made some changes within the procedures of the manufacture of TSV and the adoption of chips because of the mismatch in the Coefficient of Thermal Expansion (CTE) of the materials adopted within TSV structure, important thermal stress is going to be induced under the thermal load. The stresses are possible to cause different reliability problems. Dimension parameters are going to influence TSV’s thermal behaviors. For the purpose of optimizing the design of TSV, Cu-filled TSV’s numerical model had been set up for simulating and analyzing the influence of the thickness of SiO 2 , aspect ratio (AR), diameter and shape upon TSV thermal stress within the paper. The outcomes of the simulation present that the maximum of the areas of equivalent stress always happens at the bottom and top of the interface of Cu/SiO 2 . The aspect ratio’s influence on the equivalent stress is rather small when aspect ratio is more than 6 for vertical TSV. Vertical TSV with thicker SiO 2 layer may improve its reliability. However, the SiO 2 layer thickness does not have obvious influence for the inclined TSV upon equivalent stress.

Three-dimensional (3D) integration of silicon microelectronic devices improves the electronic functions of devices and minimizes packaging density drastically. A through-silicon via (TSV) structure is indispensable for maximizing the density of interconnections among the stacked silicon chips. However, since the TSV structure is surrounded by silicon, and there is large mismatch in materials properties between metallic materials used for the TSV structure and silicon, thermal stress is essentially generated around the TSV structure during their fabrication process and operating conditions. Recently, electroplated copper thin films have started to be applied to the interconnection material in the TSV structure because of its low electric resistivity and high thermal conductivity. However, the electrical resistivity of the electroplated copper thin films surrounded by SiO2 was found to vary drastically comparing with those of the conventional bulk material. This was because that the electroplated copper thin films consisted of grains with low crystallinity and grain boundaries, in other words, abnormally high defect density. Thus, both the crystallinity and electrical properties of the TSV structure was investigated quantitatively by changing their electroplating conditions and thermal history after the electroplating. It was observed that many voids and hillocks appeared in the TSV structures depending on the electroplating conditions. It was also found that the stress-induced migration occurred after the high temperature annealing which was introduced for improving the crystallinity of the electroplated films. Therefore, it is very important to evaluate the crystallographic quality of the electroplated copper thin films after electroplating to assure both the mechanical and electrical properties of the films.

This paper presents a micromachined stress-free through silicon via (TSV) backend process for AlGaN/GaN-on-Si (1 1 1) platform-based devices, which was processed by assisted back grinding, chemical mechanical polishing, deep reactive ion etching (DRIE) and copper (Cu) electroplating for the TSV. The metal-filled TSV structure was formed to enhance thermal conduction from the frontend terminal to the backend terminal, especially the source region of the AlGaN/GaN-on-Si (1 1 1) platform-based RF power devices. At the end of a stress-free TSV dry etching process, we have changed RF power 600 W to 300 W to minimize thermal stress of the fabricated TSV electrode pad structure of the AlGaN/GaN-on-Si platform-based devices. Additionally, we have sputtered a multi-metal layer and electroplated Cu metal to interconnect a topside electrode to TSV. To protect the thinned TSV electrode pad structure from water pressure in a sawing process, we have covered photoresist (AZ4330RS) of 3.3 µm thickness on the top area of the structures. We confirmed that the proposed TSV formation method assisted by low-power operation DRIE and protection of the thinned TSV surface by using the thick photoresist is very effective to create minimally stressed TSV structures in AlGaN/GaN-on-Si platform-based devices. The improvement was proved by the yield of dice without bursting the pad structures on a 4 inch AlGaN/GaN-on-Si wafer.

Grain characteristics of copper filler have an important influence on physical properties of through silicon vias (TSVs) in three-dimensional (3D) packaging. Due to the mismatch of coefficients of thermal expansion (CTE) between the copper and silicon, there exist obvious thermal stresses when the TSV structure is bearing thermal load. However, the elastic response characteristics of copper can be affected distinctly by the size, shape and orientation of copper grains in TSVs. These effects can not be ignored, especially for 3D ICs undergoing continuous miniaturization and increasing integration. In this study, the grain growth and evolution of a typical copper filler in the TSV structure is dynamically simulated and investigated by using Monte Carlo method (MCM), then the thermo-mechanical behavior of TSVs with considering the grain characteristics of copper filler is studied with combined MCM and finite element method (FEM), i.e., MC-FE method. Besides, the effects of grain evolution on the protrusion of copper filler in the TSV is also investigated. Simulation results are presented for providing more quantitative description and comprehensive understanding of the influences of microstructure evolution of copper filler on the thermo-mechanical behavior of Cu-filled TSVs.

In three-dimensional (3D) integrated circuit (IC), a large number of dummy through silicon vias (TSV) are required for thermal and thinning concerns. However, limited attention is paid to the fact that these dummy TSVs can be multi-functional and used for purposes. In this paper, we propose to use those timing wasteful dummy TSVs to replace bit line delay cells. Also, a TSV allocation algorithm is presented to optimize the TSV array layout. Finally, three memory designs are implemented to verify the feasibility and reliability of the proposed technology. It is found that all delay cells in these 3 memories can be replaced by TSV arrays.

In this paper, we design a new program to achieve carbon nanotubes through silicon vias (TSV) interconnects compatible with CMOS technology using an auxiliary TSV structures and laser local heating method. Auxiliary TSV structures are made by two wafers. One wafer is etched into ups and downs structures and then deposited SiN x and SiO 2 film. The other one is made into TSV structures by deep silicon etching, depositing thin film and wafer thinning and polish. Two wafers are bonded together by patterned BCB (Benzocyclobutene). For the entire device structures, we use FDTD solutions software to simulate infrared optical properties of SiN x . SiN x film layer can absorb 10.6 µm infrared laser strongly. Thermal simulation of geometrical model by COMSOL Multiphysics software shows well temperature compatibility. It turns out the program is compatible with current CMOS processes. Using a laser local heating method, we have studied the local growth of carbon nanotubes. Carbon nanotubes grown in TSVs are sparse, intertwined and have a poor morphology; the reason for this is that TSVs' geometric sizes limit gases flows. Carbon nanotubes interconnect still need further study.

Microfluidic cooling is proposed as a solution to reject heat from a 3-D IC stack of high power chips. However, the integration of interlayer microfluidic cooling in 3-D ICs inevitably increases wafer thickness and thus presents possible challenges for through-silicon via (TSV) integration. This paper discusses the thermal and electrical co-design of a microfluidic heat sink compatible with TSV technology. A TSV-compatible micropin-fin heat sink (MPFHS) with a height of 200 μm, a micropin-fin diameter of 150 μm, and a pitch of 225 μm is fabricated. The fabricated MPFHS is experimentally shown to maintain the chip junction temperature at a power density for a flow rate of 70 mL/min. The thermal results are benchmarked with an air-cooled heat sink and a chip junction temperature reduction of is observed. A 3 × 3 array of TSVs, each with a diameter of 10 μm and a height of 178 μm (18:1 aspect ratio), is integrated into each micropin-fin. This results in a TSV density of 17424 cm <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-2</sup> in the microfluidic heat sinks. Using four-point probing, the measured resistance of TSVs is 36.5±1.5 mΩ.

Nowadays, three-dimensional (3D) integration has been widely applied in semiconductor and electronics industry. When 3D integration applied in MEMS (micro electromechanical system) packaging, it is possible to stack host MEMS chip/wafer with other chips/wafers (such as ASIC) to lower package profile and realize area array sensor system. In this paper, a miniaturized piezoresistive pressure sensor system with TSV structure has been designed to demonstrate the application of TSV in MEMS packaging. TSV in pressure sensor chip is designed to provide communication paths for electrical signals. Cu/Sn bump is electroplated after exposing TSV from backside and backside metallurgy. Signal read-out chip contains redistribution circuits and Au studs. The pressure sensor chip and signal read-out chip are flip chip bonded using Au-Sn eutectic bonding. To realize this pressure sensor system, a systematic process flow including piezoresistors fabrication and circuits patterning, TSV process, flip chip bonding, polymer hermetic sealing is designed and implemented experimentally.

Increasing demand for new and more advanced electronic products, with smaller form factor and superior functionality and performance, while reducing the cost, has driven the semiconductor industry to develop more innovative and emerging advanced packaging technologies. 3D packaging, using z-axis through silicon via (TSV) stacking concept has been and continues to be investigated by many of the semiconductor manufacturers and research institutes and is believed to be one of the most promising, if not the most promising concept that could successfully address the limitations of today's packaging technologies. There is a continuous increase of interest in development and study of applicability of this new chip stacking approach to existing and future devices; currently, more than fifty companies worldwide are involved in some sort of 3D TSV packaging developments. There are several steps involved in 3D chip stacking using TSV technology. Each of these steps requires different techniques, materials and processes, applications that have to be well understood and integrated in order to successfully be applied. This paper will address various electrodeposition processes applied to form 3D interconnects, from TSV deposition, which is the main metallization step that stays at the hearth of this new technology, to other metallization steps for additional connections, such as bumping and redistribution layers, already well known and applied processes in current wafer level packaging (WLP) applications. Advantages and difficulties associated with each of these technologies, with more focus on 3D vertical integration using TSV copper interconnect, including the approaches taken to overcome them, will be presented. Deposition conditions for bumping were optimized in order to enable higher deposition rates. For other through- mask applications, such as redistribution lines (RDL), the complexity of the pattern, deposition rate, chemical formulation and process parameters were found to have a significant effect on within-die (WID) thickness distribution. In case of WLP structures of thick metal and high aspect ratios, seed layer uniformity proved to be essential for achieving void-free deposition. Void-free structures, especially for high aspect ratio vias seeded with dry methods, such as physical vapor deposition (PVD) or chemical vapor deposition (CVD), seem difficult to obtain. New approaches, such as seed layer repair (SLE) or direct on barrier electrodeposition (DOB) can provide superior uniformity and coverage of the conductive layer, necessary for a uniform nucleation of copper electrodeposition process along the entire sidewall of the via, at significantly lower costs. This paper will present TSV structures obtained with wet chemical processes applications for both seed layer and via filling. Besides seed layer uniformity, additional factors were identified to also be critical for successfully filling deep vias. They are: via profile, wettability of vias, superior performance of chemistries and high performance equipment. By selecting the most appropriate deposition methods and optimizing the chemical formulations together with the process parameters, void-free TSV structures can be obtained.