• Home
  • Search
  • Damage Localization in Complex Composite Panels Using Guided Wave Based Structural Health Monitoring System
  • Cite Icon1
  • https://doi.org/10.1115/smasis2011-5069Copy DOI Icon

Damage Localization in Complex Composite Panels Using Guided Wave Based Structural Health Monitoring System

  • Jan 1, 2011
  • Yingtao Liu +3 more
Show More
  • Abstract
  • Literature Map
  • References
  • Citations
  • Similar Papers
Abstract

Knowledge of the damage location in composite structures is a necessary output for both Non-Destructive Evaluation (NDE) and Structural Health Monitoring (SHM). Although several damage localization approaches using a triangulation method and Time-of-Flight (ToF) of guided waves have been reported in literature, the damage localization technique is still not mature for composite structures with complex material properties, varying thickness and complex geometries. This paper investigates the development of a new approach for SHM and damage localization using a guided wave based active sensing system. In contrast to the traditional ellipse method, the proposed method does not require the information of structural thickness, ToF, or the estimation of group velocities of each guided wave mode at different propagation angles, which is one of the main limitations of most current ToF methodologies involving composites. This approach uses time-frequency analysis to calculate the difference of the ToF of the converted modes for each sensor signal. The damage location and the group velocity are obtained by solving a set of nonlinear equations. The proposed method can be used for composite structures with unknown lay-up and thickness. To validate the proposed method, experiments were conducted on both composite plates and stiffened composite panels. Eight piezoelectric (PZT) transducers were surface-bonded on each composite specimen and used in four pairs. The PZT transducers in each pair were bonded close to each other. In the PZT array, one PZT transducer from one PZT pair was used as the actuator and the other three pairs were used as sensors. A windowed cosine signal was used as the excitation signal. The locations of the delaminations in the composite specimens were validated using a flash thermography system. The accuracy of the proposed method in localizing delaminations was examined through comparison with the experimental measurements.

Similar Papers
  • Research Article
  • Citations32

Structural health monitoring of seismically vulnerable RC frames under lateral cyclic loading

  • Jul 01, 2020
  • Earthquakes and Structures
  • Constantin E Chalioris +2
  • Research Article
  • Citations36

An integrated approach for structural health monitoring using an in-house built fiber optic system and non-parametric data analysis

  • Nov 25, 2014
  • Smart Structures and Systems
  • Masoud Malekzadeh +3
  • Research Article
  • Citations13

Durability of Co-bonded Piezoelectric Transducers

  • Jan 01, 2014
  • Procedia Technology
  • M Moix-Bonet +4
  • PDF
  • Research Article
  • Citations47

Evaluation of SHM System Produced by Additive Manufacturing via Acoustic Emission and Other NDT Methods

  • Oct 21, 2015
  • Sensors (Basel, Switzerland)
  • Maria Strantza +4
  • Conference Article
  • Citations82

Structural damage detection and localization using NETSHM

  • Jan 01, 2006
  • Krishna Chintalapudi +8
  • Conference Article
  • Citations10

Simulation tools for guided wave based structural health monitoring

  • Jan 01, 2018
  • AIP conference proceedings
  • Olivier Mesnil +4
  • Research Article
  • Citations9

Piezoelectric Transducer Diagnostics via Linear Reciprocity for Guided Wave Structural Health Monitoring

  • Mar 01, 2011
  • AIAA Journal
  • Sang Jun Lee +3
  • PDF
  • Research Article
  • Citations6

Experimental researching of biological objects noninvasive passive acoustothermometry features

  • Feb 29, 2020
  • Eastern-European Journal of Enterprise Technologies
  • Vitalii Didkovskyi +3
  • Research Article
  • Citations153

Locating acoustic emission sources in complex structures using Gaussian processes

  • Jun 13, 2009
  • Mechanical Systems and Signal Processing
  • J Hensman +4
  • Book Chapter
  • Citations1

Use of Deep Learning Techniques for Damage Localization in Aeronautical Composite Structures

  • Jun 22, 2022
  • Guillermo Azuara +4
  • Conference Article
  • Citations90

A complete Internet of Things (IoT) platform for Structural Health Monitoring (SHM)

  • Feb 01, 2018
  • Md Anam Mahmud +4
  • Conference Article
  • Citations3

Locating and Imaging Impact Damage with an Integrated System of PZT and Eddy Current Probe

  • May 01, 2019
  • Bo Feng +3
  • Front Matter
  • Citations74

Preface to the Special Issue on Phase I of the IASC-ASCE Structural Health Monitoring Benchmark

  • Dec 15, 2003
  • Journal of Engineering Mechanics
  • Dionisio Bernal +1
  • PDF
  • Research Article
  • Citations150

A New Structural Health Monitoring Strategy Based on PZT Sensors and Convolutional Neural Network

  • Sep 05, 2018
  • Sensors (Basel, Switzerland)
  • Mario A De Oliveira +2
  • Research Article
  • Citations12

Hybrid approach for two dimensional damage localization using piezoelectric smart aggregates

  • Sep 01, 2017
  • Mechanics Research Communications
  • Nemanja Marković +4
Cactus Communications logo

Copyright 2026 Cactus Communications. All rights reserved.