Design and Development of an Efficient EBG Structures Based Band Notched UWB Circular Monopole Antenna

This paper proposes a reconfigured horn antenna with reduced side-lobe radiation by using electromagnetic band gap (EBG) structure. A mushroom-like structure with a circular-shaped patch as unit cell is designed to achieve a complete EBG. The EBG structure is lined on the metal wall along the E-plane of the horn antenna. This causes the surface waves on the metal wall to be suppressed, resulting in lower side-lobe emission. A conducting wedge is inserted on the gap between the EBG structure and waveguide feed aperture to achieve impedance matching in the antenna. In addition, the proposed horn antenna is suitable for high power systems due to a purely metallic construction of the EBG structure.

In this paper, we present an equivalent circuit (EC) based technique which combined with the numerical method to optimize the EBG structures with simple square-loop frequency selective surfaces (FSSs), they can take on in-phase reflection characteristic in some broad-band electromagnetic band gap (EBG) structures. By using the multilayered FSSs in this type of EBG structure, the surface waves and current could stopped effectively. The geometry and working of the antenna with this EBG structure are detailed and the design method is proposed.

This paper presents a design of a dielectric resonator antenna (DRA) for millimeter-wave applications. An electromagnetic band gap (EBG) structure is used in the antenna design to enhance the antenna characteristics. The simulated with and without EBG results of the designed antenna is calculated to show the parameters such as impedance bandwidth, reflection coefficient, and gain. The parameters of the proposed antenna have improved after the periodic unit cell structure (EBG) introduction. The obtained reflection coefficients of the proposed antenna with and without EBG structure are −30.5 dB and −20.8 dB, respectively. In the presence of an EBG structure antenna shows a peak gain of 25 dBi, which is higher than the without EBG (8 dBi) structure. The designed antenna resonates at 33 GHz with an impedance bandwidth of 700 MHz. The Ansys HFSS software is used to design and simulate the proposed antenna.

This paper presents a circularly polarized printed circuit board (PCB) patch antenna using mushroom-like electromagnetic band gap (EBG) structure for gain enhancement. Unlike the popular method of using artificial magnetic conductor (AMC) or EBG structure as the ground of the antenna, we place the mushroom-like EBG structure around the patch antenna to avoid increasing the number of PCB layers. The EBG structure works in-phase reflection around 24.25 GHz by optimizing design. Limited by the size of the antenna, only twelve EBG units can be distributed around the corner-cut square circularly polarized patch antenna. Simulation results show that gain of the antenna enhances 0.8 dB and cross polarized gain reduces about 15 dB, moreover, the axial ratio is also improved.

Electromagnetic Bandgap (EBG) structures are increasingly utilized by a variety of microwave and optical devices as filters for unwanted signals. One such application is their incorporation in power distribution network (PDN) of electronic circuits where the EBG structure replaces one of the reference voltage planes thus forming a shielded EBG structure. The EBG induces a wide (on the order of few GHz) omni-directional stopband in the operating frequency range of the PDN which mitigates the so called simultaneous switching noise (SSN) on the power plane. The challenging aspect in designing an EBG for such applications is to achieve a wide stopband centered at low GHz frequencies while maintaining a reasonably small unit cell size and a low profile. Indeed, the dimensions of the unit cell of the EBG structure for low frequency designs can become relatively large with respect to the size of the host dielectric substrate. Therefore, availability of a systematic design approach that can provide a fast and accurate means of performance prediction to enable geometry tweaking and design optimization will be of critical importance in utilizing EBG structures in such applications.

In this paper a novel microstrip antenna is proposed using electromagnetic band gap (EBG) structure for mobile and wireless applications. It covers two mobile bands ranging from (2.20–2.29) GHz and (2.29–2.30) GHz. An extremely compact size EBG structure is applied in a square shape. After applying EBG structure to the proposed design, performance characteristics such as percentage bandwidth and return loss enhance by 5.1% and 5% respectively. Also by changing the feed and shorting pole (via) position, the same structure is used for ISM (2.45 ± 0.05) GHz band with resonant frequency 2.45 GHz. The measured and simulated results show very good agreement. The design structure is fabricated using FR4 substrate with dielectric constant 4.4, loss tangent 0.02 and thickness 1.6 mm.

Electromagnetic Bandgap (EBG) structures have been successfully applied for suppressing the Simultaneous Switching Noise (SSN) between the power and ground planes. Aimed at the relative narrow bandwidth and the poor performance in low frequency of the conventional Uniplanar-Compact EBG (UC-EBG) structure, a novel EBG structure formed by adding spiral-shaped metal strips on the conventional UC-EBG is proposed. This new EBG structure significantly enhance the equivalent inductance between the neighboring nuit cells, as well as change the character of the stop-band. Simulation results show that the new EBG structure can achieve a bandwidth reach 4.35GHz.This stop-band is 47.5% wider than the conventional UC-EBG structure, and 17.5% wider than the reference EBG structure in literature. The excellent SSN suppression is achieved between 0.18-4.53GHz in the depth of -40dB.

Patch antenna arrays are used extensively due to their low profile structure, light weight and low cost. Patch antenna arrays have been widely used for a variety of wireless applications. However, a major drawback of this type of antenna arrays is mutual coupling and bandwidth. Mutual Coupling losses can be reduced effectively by placing Electromagnetic band gap (EBG) structures, also called photonic band gap (PBG) structures. In this paper, different types of Electromagnetic Band Gap (EBG) structures are proposed to be placed in between the patch antenna arrays to reduce the mutual coupling loss. These EBG structures are designed as small as possible because of system compactness. Hence the design of novel compact hybrid EBG structures are more challenging for wireless applications. In this paper various hybrid EBG structures showed with and without vias are compared with the defined antenna parameters.KeywordsEBG structurespatch antenna arraysmutual coupling lossstructure realizationband passstop bandcompact sizebandwidthvias

This paper presents a printed rectangular slot microstrip antenna array of two elements based on an Electromagnetic Band Gap (EBG) structure. The proposed EBG structure is invented to improve the isolation between the radiating elements for multiple-input multiple-output (MIMO) application. Single and two slotted rectangular microstrip antennas are designed on an FR-4 substrate with a dielectric constant (εr) of 4.3 and loss tangent (tanδ) of 0.025 with thickness of 1.6 mm. The proposed EBG structure is designed as one planar row of 24 slots. The proposed array performance is tested numerically using Computer Simulation Technology Microwave Studio (CSTMW) of Finite Integration Technique (FIT) formulations. The antenna performance in terms of reflection coefficient (S11), isolation coefficient (S21), radiation patterns, boresight gain and Envelope Correlation Coefficient (ECC) are investigated before and after introducing the EBG structure to identify the significant enhancements. The proposed EBG structure is located between the radiating antenna elements to reduce the mutual coupling of the proposed antenna array. The edge to edge separation distance of the proposed antennas is λ0/16, where the λ0 is the free space wavelength at 2.45 GHz. The simulated results show a significant isolation enhancement from –6 dB to –29 dB at the first resonant frequency 2.45 GHz and from –10 dB to –25 dB at the second resonant frequency 5.8 GHz after introducing the EBG structure to the antenna array.

This paper presents an ultra-wideband monopole antenna integrated with a new configuration of electromagnetic band gap (EBG) structure. The operating frequency band of the ultra-wideband antenna is 3.1 GHz–10.6 GHz whereas the dual rejected centre frequencies are 5.2 GHz and 5.8 GHz. These two notched bands are to eliminate interference with wireless local area networks. The new proposed EBG structure is composed of a double inversed U-shape slotted patch and edge-located via. By using this new EBG structure, a high notching selectivity can be achieved for both bands. Compared to conventional mushroom-like EBG structure, the proposed configuration of the EBG structure can reject dual band instead of single band and it is 73 % smaller. The detailed theoretical explanations supported by electromagnetic full-wave simulations and confirmed by experimental measurements are introduced.

There is a strong interest to implement antenna-in-package (AiP) systems for a cohort of applications such as imaging, beamforming, integrated transceivers, and radars. Substrate integrated pyramidal antennas (SIPA) are valuable AiP candidates owing to their small form factor, integration ease, and high gain. However, height reduction and substrate integration can drastically reduce the overall directivity of such antennas and hence limit their potential applications. This degradation is mainly due to surface waves propagating and radiating on the dielectric. For the first time in this paper, we present a 94GHz low temperature cofired ceramic (LTCC) integrated pyramidal horn antenna. To prevent transverse magnetic (TM) surface waves, a mushroom type electromagnetic bandgap (EBG) structure is implemented in the surrounding of the horn. The LTCC fabrication is particularly suitable for this kind of structure. Since only a single well is needed to fabricate the horn and the EBG structure, complexity and cost are minimized. The combined antenna with EBG surrounding leads to approximately 1.8dB improvement in maximum directivity. Concurrently, the 3dB beamwidth is reduced by 10° for the E-Plane and 20° for the H-Plane.

In this paper, a novel antenna with vertical polarization and low profile in vertical direction was designed base on substrate integrated waveguide (SIW) and Electromagnetic Band Gap (EBG) structure. The radiation performance and the standing-wave ratio (SWR) were optimized via stepped transition structure. The gain and the front-to-back ratio were increased via the Electromagnetic Band Gap structure. This antenna with wide bandwidth and wide radiation lobe was base on Printed Circuit Board(PCB), and it was easy to be produced and easy for integration.

This paper presents a novel two-layer electromagnetic bandgap (EBG) structure. The studies on the characteristics of the cell are carried out numerically and experimentally. A lumped-LC equivalent circuit extracted from the numerical simulation is used to model the bandgap characteristics of the proposed EBG structure. The influences of geometric parameters on the operation frequency and equivalent LC parameters are discussed. A meander line high performance bandstop filter and a notch type duplexer are designed and measured. These EBG structures are shown to have potential applications in microwave and RF systems.

The paper aims to determine the Green's functions for different realizations of electromagnetic band-gap (EBG) structures and to calculate the coupling between two dipoles placed above these EBG structures. The applied method avoids the complexity of the Floquet mode approach and the limitations of the surface wave approach. For each considered structure, some sort of asymptotic boundary conditions are derived in which the periodicity of the structure is assumed to be negligible compared to the wavelength. The goal (and the test) of the applied method is to determine properties of each considered EBG structure. Therefore, all important physical phenomena should be taken into account. In order to be able to analyze multilayer structures, the analysis model has been implemented in the G1DMULT algorithm that calculates the spectral domain Green's functions of planar, circular-cylindrical and spherical multilayer structures (Sipus, Z. et al., App. Computational Electromagnetics Soc. J., vol.13, p.243-54, 1998).

For 60-GHz band communications, both the mutual coupling and transmission distance restrict the performance of a multiple-input multiple-output (MIMO) antenna array. Several studies presented different types of meta-materials and electromagnetic bandgap (EBG) structures to improve the performance of a MIMO antenna array at the 60-GHz band. In this paper, we presented the four-element MIMO patch antenna with different types of EBG structures for the millimeter wave (mmW)communications at the 60-GHz unlicensed industrial, scientific, and medical band. The single element of the MIMO antenna array covered the mmW band from 57 GHz to 63 GHz having the dimensions of 1.3 mm × 1.8 mm × 0.1 mm. We developed a set of square-shaped, cross-shaped, and complex-slotted EBG ground planes between the antenna elements for the performance improvement. All the three EBG ground planes provided significant coupling reduction between the mmW MIMO antenna elements. The proposed EBG structures exhibited wide bandgap characteristics and improved scattering parameters in the desired frequency band. In contrast with the cross- and complex-slotted, the square-shaped EBG structure substantially improved the overall gain of MIMO antenna array. In addition, the square-shaped EBG reformed the maximum beam and enhanced the far-field gain pattern in the desired direction. Experimental results conducted with the fabricated prototypes showed a good agreement with the simulation results and adequately covered the 60-GHz band. The low-profile and salient features of the proposed MIMO antenna array shows the potential for on-chip applications at 60 GHz.