EBG Inspired Pattern and Polarization Reconfigurable Antenna

This paper proposes a reconfigured horn antenna with reduced side-lobe radiation by using electromagnetic band gap (EBG) structure. A mushroom-like structure with a circular-shaped patch as unit cell is designed to achieve a complete EBG. The EBG structure is lined on the metal wall along the E-plane of the horn antenna. This causes the surface waves on the metal wall to be suppressed, resulting in lower side-lobe emission. A conducting wedge is inserted on the gap between the EBG structure and waveguide feed aperture to achieve impedance matching in the antenna. In addition, the proposed horn antenna is suitable for high power systems due to a purely metallic construction of the EBG structure.

In this paper, we present an equivalent circuit (EC) based technique which combined with the numerical method to optimize the EBG structures with simple square-loop frequency selective surfaces (FSSs), they can take on in-phase reflection characteristic in some broad-band electromagnetic band gap (EBG) structures. By using the multilayered FSSs in this type of EBG structure, the surface waves and current could stopped effectively. The geometry and working of the antenna with this EBG structure are detailed and the design method is proposed.

This paper presents a circularly polarized printed circuit board (PCB) patch antenna using mushroom-like electromagnetic band gap (EBG) structure for gain enhancement. Unlike the popular method of using artificial magnetic conductor (AMC) or EBG structure as the ground of the antenna, we place the mushroom-like EBG structure around the patch antenna to avoid increasing the number of PCB layers. The EBG structure works in-phase reflection around 24.25 GHz by optimizing design. Limited by the size of the antenna, only twelve EBG units can be distributed around the corner-cut square circularly polarized patch antenna. Simulation results show that gain of the antenna enhances 0.8 dB and cross polarized gain reduces about 15 dB, moreover, the axial ratio is also improved.

Electromagnetic Bandgap (EBG) structures are increasingly utilized by a variety of microwave and optical devices as filters for unwanted signals. One such application is their incorporation in power distribution network (PDN) of electronic circuits where the EBG structure replaces one of the reference voltage planes thus forming a shielded EBG structure. The EBG induces a wide (on the order of few GHz) omni-directional stopband in the operating frequency range of the PDN which mitigates the so called simultaneous switching noise (SSN) on the power plane. The challenging aspect in designing an EBG for such applications is to achieve a wide stopband centered at low GHz frequencies while maintaining a reasonably small unit cell size and a low profile. Indeed, the dimensions of the unit cell of the EBG structure for low frequency designs can become relatively large with respect to the size of the host dielectric substrate. Therefore, availability of a systematic design approach that can provide a fast and accurate means of performance prediction to enable geometry tweaking and design optimization will be of critical importance in utilizing EBG structures in such applications.

PurposeIn wireless communication system, use of multiple antennas for different requirements of system will increase the system complexity. However, reconfigurable antenna is maximizing the connectivity to cover different wireless services that operate different frequency range. Pattern reconfigurable antenna can improve security, avoid noise and save energy. Due to their compactness and better performance at different applications, reconfigurable antennas are very popular among the researchers. The purpose of this work, is to propose a novel design of S-shaped antenna with frequency and pattern diversity. The pattern and frequency reconfiguration are controlled via ON/OFF states of the PIN diode.Design/methodology/approachThe geometrical structure of the proposed antenna dimension is 18 × 18 × 0.787 mm3 with εr = 2.2 dielectric constant. Three S-shaped patches are connected to a ring patch through PIN diodes. The approximate circumference of ring patch is 18.84 mm and length of patch is 5 mm, so approximate length of radiating patch is 14.42 mm and effective dielectric constant is 1.93. Conductor backed coplanar waveguide (CPW) is used for feeding. The proposed antenna is designed and simulated on CST microwave studio and fabricated using photolithography process. Measurements have been done in anechoic chamber.FindingsAntenna shows the dual band operation at 2.1 and 3.4 GHz frequency. The first band remains constant at 2.1 GHz resonant frequency and 200–400 MHz impedance bandwidth. Second band is switched at seven different resonant frequencies as 3.14, 3.45, 3.46, 3.68, 3.69, 3.83 and 3.86 GHz with switching of the diodes. The −10 dB bandwidth is more than 1.4 GHz.Research limitations/implicationsPattern reconfigurability can be achieved using mechanical movement of antenna easily but it is not a reliable approach for planar antennas. Electronic switching method is used in proposed antenna. Antenna size is very small so fabrication is very crucial task. Measured results are deviated from simulation results due to fabrication error and effect of leads of diodes, connecting wires and battery.Practical implicationsThe reconfiguration of the proposed antenna is controlled via ON/OFF states of the three PIN diodes. The lower band of 2.1 GHz is fixed, while second band is switched at five different resonant frequencies as 3.27, 3.41, 3.45, 3.55 and 3.88 GHz, with switching of the PIN diodes with all state of diodes and exhibit pattern reconfigurability at 2.1 GHz frequency. At second band center frequency is significantly changed with state of diodes and at 3.4 GHz pattern is also changed with state of diodes, hence antenna exhibits frequency and pattern reconfigurability.Originality/valueA novel design of pattern and frequency reconfigurable antenna is proposed. Here, work is divided into two parts: first is frequency reconfiguration and second is radiation pattern reconfiguration. PIN diodes as switch are used to select the frequency band and reconfigure the radiation pattern. This proposed antenna design is novel dual band frequency and pattern reconfigurable antenna. It resonates at two distinct frequencies, i.e. 2.1 and 3.4 GHz, and has a pattern tilt from 0° to 355°. The conductor backed CPW feed technique is used for impedance matching.

Band notched circular monopole antennas for ultra-wide band applications are proposed in this paper. The proposed antennas in this paper can reject worldwide interoperability for microwave access WiMAX band (3.3–3.8 GHz) and wireless local area network WLAN band (5–6 GHz). Antennas utilises mushroom-type electromagnetic band gap (EBG) structures and I-slot embedded edge located via (ELV) EBG structures to achieve band-notched designs. The advantages of band notched designs using EBG structures like notch-frequency tuning, dual-notch antenna designs and stable radiation pattern are also verified. Various antenna designs with slot in EBG structures, variations in placement of EBG structures, number of EBG structures and ELV type EBG structures are simulated. About 30% reduction in size of EBG structures is obtained if conventional mushroom type EBG is replaced by proposed I-slot embedded ELV-EBG structure. Fabricated and measured results are in good agreement with simulated ones.

This paper presents a design of a dielectric resonator antenna (DRA) for millimeter-wave applications. An electromagnetic band gap (EBG) structure is used in the antenna design to enhance the antenna characteristics. The simulated with and without EBG results of the designed antenna is calculated to show the parameters such as impedance bandwidth, reflection coefficient, and gain. The parameters of the proposed antenna have improved after the periodic unit cell structure (EBG) introduction. The obtained reflection coefficients of the proposed antenna with and without EBG structure are −30.5 dB and −20.8 dB, respectively. In the presence of an EBG structure antenna shows a peak gain of 25 dBi, which is higher than the without EBG (8 dBi) structure. The designed antenna resonates at 33 GHz with an impedance bandwidth of 700 MHz. The Ansys HFSS software is used to design and simulate the proposed antenna.

In this paper a novel microstrip antenna is proposed using electromagnetic band gap (EBG) structure for mobile and wireless applications. It covers two mobile bands ranging from (2.20–2.29) GHz and (2.29–2.30) GHz. An extremely compact size EBG structure is applied in a square shape. After applying EBG structure to the proposed design, performance characteristics such as percentage bandwidth and return loss enhance by 5.1% and 5% respectively. Also by changing the feed and shorting pole (via) position, the same structure is used for ISM (2.45 ± 0.05) GHz band with resonant frequency 2.45 GHz. The measured and simulated results show very good agreement. The design structure is fabricated using FR4 substrate with dielectric constant 4.4, loss tangent 0.02 and thickness 1.6 mm.

Electromagnetic Bandgap (EBG) structures have been successfully applied for suppressing the Simultaneous Switching Noise (SSN) between the power and ground planes. Aimed at the relative narrow bandwidth and the poor performance in low frequency of the conventional Uniplanar-Compact EBG (UC-EBG) structure, a novel EBG structure formed by adding spiral-shaped metal strips on the conventional UC-EBG is proposed. This new EBG structure significantly enhance the equivalent inductance between the neighboring nuit cells, as well as change the character of the stop-band. Simulation results show that the new EBG structure can achieve a bandwidth reach 4.35GHz.This stop-band is 47.5% wider than the conventional UC-EBG structure, and 17.5% wider than the reference EBG structure in literature. The excellent SSN suppression is achieved between 0.18-4.53GHz in the depth of -40dB.

The present work represents polarization reconfigurable MIMO antenna which is design to work at 2.4 GHz (WLAN) and C band application. An inverted U-shaped slot and two PIN diodes per radiator are incorporated in the circular patch antenna to achieve polarization reconfigurability between Linear and Circular polarization (RHCP or LHCP). A simple rectangular strip is utilized between the radiators to achieve isolation improvement from -14 dB to -22dB in the proposed design. Computer Simulation Technology (CST) 2018 is used to design and validate the polarization reconfigurable MIMO antenna with sufficient isolation. Surface current distribution, Envelope Correlation Coefficient (ECC) and Diversity Gain (DG) and axial ratio are calculated using simulation software and used to validate circularly polarized MIMO design’s diverse behavior. The design is fabricated in low-cost FR-4 material and measurement is done to verify the simulation results. The measurement results show close agreement with simulated results and proves that the proposed design can be a better candidate for WLAN and C band application with polarization reconfiguration properties.

Patch antenna arrays are used extensively due to their low profile structure, light weight and low cost. Patch antenna arrays have been widely used for a variety of wireless applications. However, a major drawback of this type of antenna arrays is mutual coupling and bandwidth. Mutual Coupling losses can be reduced effectively by placing Electromagnetic band gap (EBG) structures, also called photonic band gap (PBG) structures. In this paper, different types of Electromagnetic Band Gap (EBG) structures are proposed to be placed in between the patch antenna arrays to reduce the mutual coupling loss. These EBG structures are designed as small as possible because of system compactness. Hence the design of novel compact hybrid EBG structures are more challenging for wireless applications. In this paper various hybrid EBG structures showed with and without vias are compared with the defined antenna parameters.KeywordsEBG structurespatch antenna arraysmutual coupling lossstructure realizationband passstop bandcompact sizebandwidthvias

This paper presents a novel two-layer electromagnetic bandgap (EBG) structure. The studies on the characteristics of the cell are carried out numerically and experimentally. A lumped-LC equivalent circuit extracted from the numerical simulation is used to model the bandgap characteristics of the proposed EBG structure. The influences of geometric parameters on the operation frequency and equivalent LC parameters are discussed. A meander line high performance bandstop filter and a notch type duplexer are designed and measured. These EBG structures are shown to have potential applications in microwave and RF systems.

This paper presents an embedded on-body planar monopole antenna using a low profile electromagnetic band gap (EBG) structure. The EBG structure consists of the series capacitance between an inter-digital slot and the shunt inductance through a via. Using the band-gap characteristic of the EBG array, a planar monopole antenna which has an isotropic radiation pattern could be mounted on the human body with low interference. The planar monopole has an advantage of miniaturization compared to the patch antenna which is usually used in on-body communication. By using the low profile EBG structure, the thin antenna is applicable to on-body communication systems.

Aim of this paper is to describe the simultaneous switching noise (SSN) mitigation by means of a novel electromagnetic band gap (EBG) structure with triangle patches and hexagonal array. The proposed EBG structure allows achieving -40 dB stop band within the frequency range 6.5-9 GHz. Parametric analysis including the radius effect of the metal plated vias, the via length and the distance between the patches is performed by means of full wave simulations, based on the Finite Integration Technique. The impact of the proposed design on the signal integrity is also investigated both in time domain (eye-diagrams and TDR) and frequency domain (S-parameters). Finally dispersion diagrams of the singular unit EBG cell are analyzed by means of eigenmode solver and periodic boundary conditions.

The paper aims to determine the Green's functions for different realizations of electromagnetic band-gap (EBG) structures and to calculate the coupling between two dipoles placed above these EBG structures. The applied method avoids the complexity of the Floquet mode approach and the limitations of the surface wave approach. For each considered structure, some sort of asymptotic boundary conditions are derived in which the periodicity of the structure is assumed to be negligible compared to the wavelength. The goal (and the test) of the applied method is to determine properties of each considered EBG structure. Therefore, all important physical phenomena should be taken into account. In order to be able to analyze multilayer structures, the analysis model has been implemented in the G1DMULT algorithm that calculates the spectral domain Green's functions of planar, circular-cylindrical and spherical multilayer structures (Sipus, Z. et al., App. Computational Electromagnetics Soc. J., vol.13, p.243-54, 1998).