Implementation of Deep Learning in Spatial Multiplexing MIMO Communication

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

Multiple-input multiple-output (MIMO) wireless communication systems rely upon the knowledge of channel state information (CSI) at the receiver for data detection and decoding. In this paper, a better performance and reduced complexity channel estimation method is proposed for MIMO systems based on matrix factorization. This technique is applied on least squares (LS) channel estimation for performance improvement. Experimentation results indicate that the proposed method not only alleviates the performance of channel estimation but also significantly reduces the complexity caused by matrix inversion. The performance evaluations are validated through computer simulations using MATLAB® 7.0 in terms of BER. Simulation results show that the performance and complexity of the proposed method clearly outperforms the conventional LS channel estimation method.

Traditional receiver algorithms developed for multiple-input multiple-output (MIMO) wireless communication systems are based on the assumption that the channel state information (CSI) is perfectly known at the receiver. However, in real environments the exact CSI is unavailable. In this paper, we address the problem of robustness of multiuser space-time block coded MIMO systems against imperfect CSI and develop a simple linear receiver which guarantees robustness against CSI errors with a certain selected probability. The proposed receiver is formulated via a probability-constrained optimization problem which is further relaxed using Chebyshev inequality to a much simpler second-order cone programming (SOCP) problem. Simulations demonstrate that the proposed receiver has a moderate performance degradation as compared to the exact solution to the original probability-constrained optimization problem, while offering much simpler implementation.

In conventional ways of fast responding and high performing model predictive control using Field Programmable Gate Arrays (FPGA), the approaches developed are applicable only to Single Input Single Output System (SISO). Many real time systems are Multiple Input Multiple Output (MIMO) systems and loop interaction is a major concern and has to be reduced in control of MIMO systems. Also, direct digital control with ability to solve the Quadratic Programming (QP) problem online, which can be applied to complex systems with fast response time and/or embedded applications and with limited computational resource for supervisory control approach, is required in many complex industrial MIMO systems. A novel direct digital control of Model predictive controller with FPGA for a MIMO system which considers and reduces loop interaction and which can also be implemented with very less investment is proposed here. The system was modeled from first principles and then simulated in Labview environment for MIMO system. Implementation of the system and response was verified for a stirred tank system. The proposed system has good performance in terms of reduction in loop interaction which is a major concern in implementation of controller for MIMO systems. Also, direct digital control of MIMO system instead of supervisory control was accomplished.

The capacity of multiple-input multiple-output (MIMO) wireless communication systems over spatially correlated Rayleigh distributed flat fading channels with complex Gaussian additive noise is investigated. Specifically, the probability density function of the mutual information between transmitted and received complex signals of MIMO systems is derived. Using this density the closed-form ergodic capacity (mean), delay-limited capacity, capacity variance and outage capacity formulas for spatially correlated channels are derived and then these formulas are evaluated numerically. Numerical results show how the channel correlation degrades the capacity of MIMO communication systems. It is also shown that the density of mutual information of correlated/uncorrelated MIMO systems can be approximated by a Gaussian density with derived mean and variance, even for a finite number of inputs and outputs.

Nonlinearities play an imperative role in performance of wireless communication systems. In this paper, High Power Amplifiers (HPA) have been used to check the performance of the proposed system by analyzing its amplitude, phase and their joint distortions using Multiple-Input Multiple-Output (MIMO) wireless communication system. This paper takes-in account the overall effects of HPA that provokes nonlinearities at the transmitter's end in a communication system. Therefore, a novel method for the HPA nonlinearities mitigation has been proposed to improve the performance of amplitude, phase and joint distortions in MIMO communication systems. The simulation results show an improvement in the overall effect of the MIMO system and enhance the input response on the transmitter side. Furthermore, this method has been proposed to exploit the benefits of the MIMO system to improve the Symbol Error Rate (SER) versus Signal to Noise Ratio (SNR) curves for amplitude, phase and their joint distortions.

Orbital Angular Momentum (OAM) has been considered as a new dimension in wireless transmission. In Multiple Input Multiple Output (MIMO) system, OAM can also be utilized as the new Degrees of Freedom (DoF) to manipulate the beamforming instead of the traditional Channel State Information (CSI) feedback, so that the computation complexity of the beamforming dramatically decreases, as well as the capacity of the transmission is maintained approaching the upper bound of the MIMO system. For example, this beamforming manipulation with OAM is extremely efficient in the Line of Sight (LoS) MIMO system. In this paper, the mathematical model of the DoF in beamforming manipulation in MIMO with OAM is established. The computation complexity is evaluated, and compared in LoS environment within MIMO, MIMO-OAM, and OAM. The quantitatively simulation confirms the fact that MIMO-OAM has the best trade-off between the capacity and the computation complexity, which gives a consolidated evidence that the MIMOOAM scheme can be adopted as an efficient beamforming scheme in LoS backhaul links between the base station and the self backhaul small cell station, or Near Field Communications (NFC) directly between mobile terminals. Due to these promising applications, MIMO-OAM may become one of the candidate technologies in Beyond 5G (B5G) mobile communications.

The fifth generation cellular communication is all about high speed internet access with devices consuming less amount of power. Millimeter wave Multiple Input Multiple Output (MIMO) systems is a promising technology that offers high data rates due to a large bandwidth. These systems are compact with minimal antenna heights which allows us to deploy these systems more widely. The mm-Wave Massive MIMO systems enhances the data rates to a large extent. But due to the increasing number of antennas to support high data rates, the power consumption of the system goes high. In this paper, a limited channel state information (CSI) based precoding technique has been used to optimize the power consumption and to reduce the computational complexity of the system. The use of Hybrid Precoder architecture with sub array of precoding blocks helps in reducing the computational complexity by many folds. The conditional switching between two stages minimizes the number of computations required. The estimation of Angle of arrival (AoA) enables the precoder to steer the beam at the transmitter for higher throughput. The smart antenna selection algorithm optimizes the power consumption of the system. The two – staged precoding algorithm proposed employs all these techniques to optimize the performance of mm-Wave MIMO systems.

This paper has proposed an adaptive antenna selection technique in multiple input multiple output (MIMO) system that optimizes the system energy efficiency to achieve maximum throughput. Though throughput increases with the dimension of MIMO system, the energy consumed per RF module is a major concern. The antenna selection technique exploits the channel state information (CSI) at transmitting end to reduce the number of RF module to achieve maximum benefit out of MIMO system. However, simultaneously achievement of best throughput and energy efficiency, with fixed number of transmitted antennas, is not possible. In this paper, the number of transmitting antenna to be selected is varied as per channel condition. The proposed technique aims to maximize the instantaneous throughput with optimum energy efficiency.

Visible Light Communication (VLC) has emerged as a powerful technique for wireless communication systems. Providing high data rate and increasing capacity are the major problems in VLC. Recent evidence suggests that Multiple Input Multiple Output (MIMO) technique can offers improved data rates and increased link range. This paper describes the design and implementation of visible light communication system in indoor environment exploring the benefits of MIMO. The specific objective of this research was to implement a 4×4 Multiple Input (LEDs) Multiple Output (photodetectors)-VLC communication system, where a 16 white power LEDs in four arrays are setting up at transmitter and four RX modules are setting up at receiver side without the need for additional power or bandwidth as well as analyze a mathematical model for a VLC- 4×4 MIMO with different modes such as the suitable angles to cover the entire room. The research designs practically an electronic circuit for the transmitter and receiver with inexpensive components. The power distribution of different propagation modes is calculated for Single Input Single Output (SISO) and MIMO channels in typical room dimensions. The results in this paper indicate that the power is distributed uniformly for entire room when implemented VLC-MIMO as compared to VLC-SISO. Furthermore, a 4×4 MIMO implementing VLC is compared in term of BER vs. SINR with SISO communication system for both Line of Sight (LOS) and Non Line of Sight (NLOS) propagation modes. Comparing the two results of LOS and NLOS, it can be seen that a 4×4 MIMO implementing VLC for LOS perform better than the same system with NLOS due to decreasing in the received power resulted from the multipath effect.

Multiple Input Multiple Output(MIMO) has been in much importance in recent past because of high capacity gain over a single antenna system. In this article, analysis over the capacity of the MIMO channel systems with spatial channel with modified precoder and decoder has been considered when the channel state information (CSI) is considered partial. Due to delay in acquiring transmitted information at the receiver end, the time selective fading wireless channel often induces incomplete or partial CSI. The dynamic CSI model has also been implemented consisting channel mean and covariance which leads to extracting of channel estimates and error covariance which then further applied with the modified precoder and decoder utilizing both the parameters indicating the CSI quality since these are the functions of temporal correlation factor, and based on this, the model covers data from perfect to statistical CSI, either partially or fully blind. It is found that in case of partial and imperfect CSI, the capacity depends on the statistical properties of the error in the CSI which has been manipulated according to the precoder and decoder conditions. Based on the knowledge of statistical distribution of the deviations in CSI knowledge, a new approach which maximizes the capacity of spatial channel model with modified precoder and decoder has been tried. The interference then interactively reduced by employing the iterative channel estimation and data detection approach, where by utilizing the detected symbols from the previous iteration, multiuser/MIMO channel estimation and symbol detection is improved.

We propose a precoder design to minimize the codeword error rate of multiple-input multiple-output (MIMO) systems in the presence of channel estimation errors. Our proposed scheme only requires knowledge of the second-order statistics of the channel, noise and the estimation errors; an estimate of the instantaneous channel state information (CSI) is not required. Compared to the instantaneous CSI requirement, our assumption is more practical since obtaining an accurate CSI is challenging if the channel fluctuates rapidly, while the channel statistics are likely to remain unchanged for a much longer period. Furthermore, the feedback overhead from the receiver to the transmitter is greatly reduced. When compared to the case without transmit preceding, our proposed design achieves a significant improvement in error performance: (i) for a real 2 × 2 MIMO system with 4-PAM modulation and at codeword error rate of 104, our proposed precoder design achieves coding gains of up to 6 dB and (ii) for a real 4 × 4 MIMO system with BPSK modulation and at codeword error rate of 104, coding gains of up to 6.5 dB can be achieved.

Multiple-input multiple-output (MIMO) has been accepted as a promising technology for its potential to achieve low bit error rate (BER) by space time coding [1] or to achieve large capacity by multiplexing [2]. MIMO multiplexing has been widely adopted to realize high speed data communications. The capacity of MIMO systems in the point-to-point transmission without external interferences has been studied in [3, 4] to show that large capacity can be achieved in a rich scattering environment. In a cellular environment, the same frequency/frequencies can be used in neighboring cells. As a result, co-channel interference exists and the channel between the base-station (BS) and the mobile-station (MS) is changed from noise-limited channel to interference-limited channel. Recently, the capacity of MIMO systems in the cellular environment has attracted much interest. Uplink (transmission from MS to BS) capacity with variable-rate transmissions is studied in [5]. By modeling the co-channel interference as additive white Gaussian noise (AWGN), the uplink capacity is also studied in [6, 7]. On the other hand, from the users’ stand point, the downlink capacity may be more interesting. However, the results for the downlink capacity of cellular MIMO systems presented in the literature are mainly based on the simulation results. Very detailed simulation results for the downlink MIMO capacity in 3G FDD WCDMA cellular systems can be found in [8]. By assuming single-frequency-reuse (the frequency reuse factor (FRF) equals to 1), the capacity of downlink cellular MIMO systems is studied by simulations and the results are presented in [9, 10]. These results are given in terms of the number of antennas, the modulation schemes, the propagation parameters as well as the cell size. However, FRFs other than 1 are not considered. By taking various FRFs into consideration, a comparative study on the capacity of cellular MIMO systems is presented in [11]. A comprehensive comparison between the capacity of SISO, SIMO, STBC-MISO and MIMO systems in a cellular environment is made based on the simulation results. In general, fixed FRF has been considered in cellular systems. It is reported in [12] that a flexible FRF may help to improve the capacity for cellular single antenna (SISO) systems. However, flexible design of FRF for cellular MIMO systems is rarely available in the literature. In this chapter, the downlink capacity of cellular MIMO systems is theoretically analyzed in terms of both the ergodic and outage capacities. The theoretical results of the best and worst situation capacities suggest that the greatest capacities may be achieved by using FRF 1 or FRF 3 adaptively according to the situations. Therefore, a hybrid frequency reuse scheme is

Consider a multiple input multiple output (MIMO) system with pulse amplitude modulation (PAM), where each transmit antenna is allowed to choose a different transmission delay. (We refer to this system as a MIMO system with asynchronous PAM.) Such MIMO systems have been studied before for increasing diversity and avoiding unintentional beamforming. We quantify the capacity/outage capacity improvement due to asynchronism and the corresponding spectral leakage (if any) for MIMO point-to-point and MIMO broadcast channels. We show that under commonly used transmitter spectral mask constraints, the channel has unbounded degrees of freedom. Synchronous PAM exploits only a finite number of these degrees of freedom, and asynchronism helps to improve capacity. For most cases of interest, two distinct shifts attain most of the capacity improvement. These gains are robust to interference from adjacent carriers. Analysis of the spectrum of the asynchronous PAM suggests that optimal water-filling based schemes are useful for improving capacity only in directional links due to possible spectral leakage, while uniform power allocation leads to capacity improvement without any extra spectral leakage.

After a few decades’ evolution of wireless communication systems, to ensure reliable highspeed communication over unreliable wireless channels is still one of the major challenges facing researchers and engineers. The use of multiple antennas at transmitter and receiver, known as multiple-input multiple-output (MIMO) communications, is one promising technology delivering desired wireless services. The main goal of this thesis is to study two important issues in wireless MIMO communication systems: receiver design for coded MIMO systems, and diversity-multiplexing tradeoff analysis in general fading channels. In the first part of this thesis, we decompose the receiver design problem into two subproblems: MIMO channel estimation and MIMO detection. For the MIMO channel estimation, we develop an expectation-maximization (EM) based semi-blind channel and noise covariance matrix estimation algorithm for space-time coding systems under spatially correlated noise. By incorporating the proposed channel estimator into the iterative receiver structure, both the channel estimation and the error-control decoding are improved significantly. We also derive the modified Cramer-Rao bounds (MCRB) for the unknown parameters as the channel estimation performance metric, and demonstrate that the proposed channel estimation algorithm can achieve the MCRB after several iterations. For the MIMO detection, we propose a novel lowcomplexity MIMO detection algorithm, which has only cubic order computational complexity, but with near-optimal performance. For a 4×4 turbo-coded system, we show that the proposed detector had the same performance as the maximum a posteriori (MAP) detector for BPSK modulation, and 0.1 dB advantage over the approximated MAP detector (list sphere decoding algorithm) for 16-QAM modulation at BER = 10−4. In the second part of this thesis, we derive the optimal diversity-multiplexing tradeoff for