Spatially correlated multiple-antenna channel capacity distributions

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

Multiple-input multiple-output (MIMO) has been accepted as a promising technology for its potential to achieve low bit error rate (BER) by space time coding [1] or to achieve large capacity by multiplexing [2]. MIMO multiplexing has been widely adopted to realize high speed data communications. The capacity of MIMO systems in the point-to-point transmission without external interferences has been studied in [3, 4] to show that large capacity can be achieved in a rich scattering environment. In a cellular environment, the same frequency/frequencies can be used in neighboring cells. As a result, co-channel interference exists and the channel between the base-station (BS) and the mobile-station (MS) is changed from noise-limited channel to interference-limited channel. Recently, the capacity of MIMO systems in the cellular environment has attracted much interest. Uplink (transmission from MS to BS) capacity with variable-rate transmissions is studied in [5]. By modeling the co-channel interference as additive white Gaussian noise (AWGN), the uplink capacity is also studied in [6, 7]. On the other hand, from the users’ stand point, the downlink capacity may be more interesting. However, the results for the downlink capacity of cellular MIMO systems presented in the literature are mainly based on the simulation results. Very detailed simulation results for the downlink MIMO capacity in 3G FDD WCDMA cellular systems can be found in [8]. By assuming single-frequency-reuse (the frequency reuse factor (FRF) equals to 1), the capacity of downlink cellular MIMO systems is studied by simulations and the results are presented in [9, 10]. These results are given in terms of the number of antennas, the modulation schemes, the propagation parameters as well as the cell size. However, FRFs other than 1 are not considered. By taking various FRFs into consideration, a comparative study on the capacity of cellular MIMO systems is presented in [11]. A comprehensive comparison between the capacity of SISO, SIMO, STBC-MISO and MIMO systems in a cellular environment is made based on the simulation results. In general, fixed FRF has been considered in cellular systems. It is reported in [12] that a flexible FRF may help to improve the capacity for cellular single antenna (SISO) systems. However, flexible design of FRF for cellular MIMO systems is rarely available in the literature. In this chapter, the downlink capacity of cellular MIMO systems is theoretically analyzed in terms of both the ergodic and outage capacities. The theoretical results of the best and worst situation capacities suggest that the greatest capacities may be achieved by using FRF 1 or FRF 3 adaptively according to the situations. Therefore, a hybrid frequency reuse scheme is

Consider a multiple input multiple output (MIMO) system with pulse amplitude modulation (PAM), where each transmit antenna is allowed to choose a different transmission delay. (We refer to this system as a MIMO system with asynchronous PAM.) Such MIMO systems have been studied before for increasing diversity and avoiding unintentional beamforming. We quantify the capacity/outage capacity improvement due to asynchronism and the corresponding spectral leakage (if any) for MIMO point-to-point and MIMO broadcast channels. We show that under commonly used transmitter spectral mask constraints, the channel has unbounded degrees of freedom. Synchronous PAM exploits only a finite number of these degrees of freedom, and asynchronism helps to improve capacity. For most cases of interest, two distinct shifts attain most of the capacity improvement. These gains are robust to interference from adjacent carriers. Analysis of the spectrum of the asynchronous PAM suggests that optimal water-filling based schemes are useful for improving capacity only in directional links due to possible spectral leakage, while uniform power allocation leads to capacity improvement without any extra spectral leakage.

Nonlinearities play an imperative role in performance of wireless communication systems. In this paper, High Power Amplifiers (HPA) have been used to check the performance of the proposed system by analyzing its amplitude, phase and their joint distortions using Multiple-Input Multiple-Output (MIMO) wireless communication system. This paper takes-in account the overall effects of HPA that provokes nonlinearities at the transmitter's end in a communication system. Therefore, a novel method for the HPA nonlinearities mitigation has been proposed to improve the performance of amplitude, phase and joint distortions in MIMO communication systems. The simulation results show an improvement in the overall effect of the MIMO system and enhance the input response on the transmitter side. Furthermore, this method has been proposed to exploit the benefits of the MIMO system to improve the Symbol Error Rate (SER) versus Signal to Noise Ratio (SNR) curves for amplitude, phase and their joint distortions.

Everyone in the world always wants to use a better wireless network which provide high capacity and high data rates. High data rates and capacity can be produce by Multiple Input Multiple Output(MIMO) systems. This paper mainly focused on MIMO systems because the MIMO systems have multiple number of antennas in transmitting and receiving end which can produce more data rates and capacity compared to SISO, SIMO, MISO systems. The multiple antennas allow MIMO systems to produce multiplexing gain and diversity gain. The capacity of MIMO systems will be increased by increased the number of antennas in transmitter and receiver end.

Multiple-input multiple-output (MIMO) wireless communication systems can achieve higher throughput through interference alignment. For a small number of users, determining the maximum possible degrees of freedom as well as the feasibility of interference alignment in MIMO systems is well studied. However, the issues of scheduling in systems employing interference alignment and serving a large number of users have received little attention so far. In this paper, we study the problem of joint scheduling, interference alignment, and packet admission control in MIMO wireless systems with the goal of maximizing system throughput subject to stability constraints. We formulate a stochastic network optimization problem and propose a scheduling and interference alignment (SIA) algorithm. In each time slot, SIA schedules some users among many competing ones to transmit data, and determines encoding and decoding matrices for the selected users. Packet admission control is performed in each time slot. In addition, we propose a heuristic semi-distributed algorithm (SDSIA), which has a lower computational complexity than the SIA algorithm. Via simulation, we evaluate the performance of SIA and SDSIA for different algorithm parameters and different numbers of users. We also compare the performance of SDSIA with other approaches which do not simultaneously exploit interference alignment and scheduling and find that the combination of these two techniques increases the achievable data rate dramatically.

Traditional receiver algorithms developed for multiple-input multiple-output (MIMO) wireless communication systems are based on the assumption that the channel state information (CSI) is perfectly known at the receiver. However, in real environments the exact CSI is unavailable. In this paper, we address the problem of robustness of multiuser space-time block coded MIMO systems against imperfect CSI and develop a simple linear receiver which guarantees robustness against CSI errors with a certain selected probability. The proposed receiver is formulated via a probability-constrained optimization problem which is further relaxed using Chebyshev inequality to a much simpler second-order cone programming (SOCP) problem. Simulations demonstrate that the proposed receiver has a moderate performance degradation as compared to the exact solution to the original probability-constrained optimization problem, while offering much simpler implementation.

We present a hybrid soft detector that has a good performance/complexity trade-off for a multiple-input multiple-output (MIMO) wireless communication system with known channel information. The new soft detector combines the merits of a simple unstructured least-squares (LS)-based soft detector and a list sphere decoder (LSD)-based soft detector for data bit detection. The former is computationally much more efficient than the latter at the cost of poorer performance. The poor performance of the former occurs mainly when the channel matrix is ill-conditioned. Whenever this happens, we use the LSD-based soft detector in the hybrid soft detector; otherwise, we use the LS-based one. Moreover, we provide a tight radius for a sphere decoder, a hard detector, via using the output of an LS-based hard detector. These two hard detectors are needed to determine if LS or LSD should be used in the hybrid soft detector. As an application example, we consider doubling the maximum data rate of the IEEE 802.11a conformable wireless local area networks by a MIMO system with two transmit and two receive antennas. For this application, the new soft detector is about 10 times faster than the LSD-based one and is about 10 times slower than the LS-based one. Yet the packet error rate due to using the new soft detector is quite close to that of using the LSD-based one.

Wireless communications using multiple input multiple output (MIMO) systems enable increased spectral efficiency for a given total transmit power. The increased capacity is achieved through the introduction of additional spatial channels (space-time coding). In this paper, MIMO capacity is calculated as a function of environmental factors, including channel complexity, external interference and channel estimation error. The capacity of MIMO systems, where both the transmitter and receiver know the channel (channel estimate feedback), is compared with single input multiple output (SIMO) and MIMO systems, where only the receiver knows the channel. The channel complexity is studied using a simple statistical physical scattering model. Finally, an expression for capacity loss particular to channel estimation error at the transmitter is introduced.

In conventional ways of fast responding and high performing model predictive control using Field Programmable Gate Arrays (FPGA), the approaches developed are applicable only to Single Input Single Output System (SISO). Many real time systems are Multiple Input Multiple Output (MIMO) systems and loop interaction is a major concern and has to be reduced in control of MIMO systems. Also, direct digital control with ability to solve the Quadratic Programming (QP) problem online, which can be applied to complex systems with fast response time and/or embedded applications and with limited computational resource for supervisory control approach, is required in many complex industrial MIMO systems. A novel direct digital control of Model predictive controller with FPGA for a MIMO system which considers and reduces loop interaction and which can also be implemented with very less investment is proposed here. The system was modeled from first principles and then simulated in Labview environment for MIMO system. Implementation of the system and response was verified for a stirred tank system. The proposed system has good performance in terms of reduction in loop interaction which is a major concern in implementation of controller for MIMO systems. Also, direct digital control of MIMO system instead of supervisory control was accomplished.

Multiple-input multiple-output (MIMO) wireless communications systems have attracted a lot of attentions, because of their potential for high gain in channel capacity. Recently, attention has shifted to multiuser MIMO (MU-MIMO) systems. In the schemes for downlink MU-MIMO system, dirty paper coding (DPC) and block diagonalization (BD) algorithms can provide higher sum rate capacity of MU-MIMO systems; however, exhaustive user scheduling for them may cause prohibitive computation complexity. The greedy scheduling algorithms were proposed for DPC and for BD; and proportionally fair (PF) scheduling for MU-MIMO was also discussed in the previous works. However, the discussions in where mainly based on the system model with equal average signal to noise power ratio (SNR) users. In this paper, we focus on the user scheduling for the downlink of MU-MIMO systems with DPC transmission scheme, where each user is assumed to have only one receive antenna, which will simplify the analysis and is expected to give more insight of PF scheduling. We also assume each individual user has different average transmit SNR in the system. We modify the conventional user scheduling algorithm for DPC to modified Gram-Schmidt orthogonalization (M-GSO) based algorithm and extend it into PF scheduling. We also propose a modified PF metric corresponding to the unequal SNR users system model, that increases the sum rate capacity of MU-MIMO system.

Independent component analysis for multiple-input multiple-output wireless communication systems

The free space optical (FSO) communication system has attracted many researchers from different countries, owning to its advantages such as high security, high speed and anti-interference. Among all kinds of the channels of the FSO communication system, the atmosphere channel is very difficult to deal with for two typical disadvantages at least. The one is the scintillation of the optical carrier intensity caused by the atmosphere turbulence and the other is the multipath effect by the optical scattering. A lot of studies have shown that the MIMO (Multiple Input Multiple Output) technology can overcome the scintillation of the optical carrier through the atmosphere effectively. So the background of this paper is a MIMO system which includes multiple optical transmitting antennas and multiple optical receiving antennas. A number of particles such as hazes, water droplets and aerosols exit in the atmosphere widely. When optical carrier meets these particles, the scattering phenomenon is inevitable, which leads to the multipath effect. As a result, a optical pulse transmitted by the optical transmitter becomes wider, to some extent, when it gets to the optical receiver due to the multipath effect. If the information transmission rate is quite low, there is less relationship between the multipath effect and the bit error rate (BER) of the communication system. Once the information transmission rate increases to a high level, the multipath effect will produce the problem called inter symbol inference (ISI) seriously and the bit error rate will increase severely. In order to take the advantage of the FSO communication system, the inter symbol inference problem must be solved. So it is necessary to use the channel equalization technology. This paper aims at deciding a equalizer and designing suitable equalization algorithm for a MIMO free space optical communication system to overcome the serious problem of bit error rate. The reliability and the efficiency of communication are two important indexes. For a MIMO communication system, there are two typical equalization methods. The first method, every receiving antenna has an independent equalizer without the information derived from the other receiving antennas. The second, the information derived from all of the receiving antennas mixes with each other, according to some definite rules, which is called space-time equalization. The former is discussed in this paper. The equalization algorithm concludes training mode and non training mode. The training mode needs training codes transmitted by the transmitter during the whole communication process and this mode reduces the communication efficiency more or less. In order to improve the communication efficiency, the blind equalization algorithm, a non training mode, is used to solve the parameter of the equalizer. In this paper, firstly, the atmosphere channel is described focusing on the scintillation and multipath effect of the optical carrier. Then, the structure of a equalizer of MIMO free space optical communication system is introduced. In the next part of this paper, the principle of the blind equalization algorithm is introduced. In addition, the simulation results are showed. In the end of this paper, the conclusions and the future work are discussed.

After a few decades’ evolution of wireless communication systems, to ensure reliable highspeed communication over unreliable wireless channels is still one of the major challenges facing researchers and engineers. The use of multiple antennas at transmitter and receiver, known as multiple-input multiple-output (MIMO) communications, is one promising technology delivering desired wireless services. The main goal of this thesis is to study two important issues in wireless MIMO communication systems: receiver design for coded MIMO systems, and diversity-multiplexing tradeoff analysis in general fading channels. In the first part of this thesis, we decompose the receiver design problem into two subproblems: MIMO channel estimation and MIMO detection. For the MIMO channel estimation, we develop an expectation-maximization (EM) based semi-blind channel and noise covariance matrix estimation algorithm for space-time coding systems under spatially correlated noise. By incorporating the proposed channel estimator into the iterative receiver structure, both the channel estimation and the error-control decoding are improved significantly. We also derive the modified Cramer-Rao bounds (MCRB) for the unknown parameters as the channel estimation performance metric, and demonstrate that the proposed channel estimation algorithm can achieve the MCRB after several iterations. For the MIMO detection, we propose a novel lowcomplexity MIMO detection algorithm, which has only cubic order computational complexity, but with near-optimal performance. For a 4×4 turbo-coded system, we show that the proposed detector had the same performance as the maximum a posteriori (MAP) detector for BPSK modulation, and 0.1 dB advantage over the approximated MAP detector (list sphere decoding algorithm) for 16-QAM modulation at BER = 10−4. In the second part of this thesis, we derive the optimal diversity-multiplexing tradeoff for

This paper considers large multiple-input multiple-output (MIMO) communication systems with linear precoding and linear minimum mean-squared error (LMMSE) equalization based on the iterative conjugate gradient (CG) algorithm. Convergence of the CG algorithm is fast when the eigenvalues of the received signal's covariance matrix are clustered, suggesting that mean-squared error and receiver complexity can be managed with judicious precoder design. In order to accelerate convergence of an iterative CG receiver, we incorporate constraints on two measures of eigenvalue clustering into the precoder design. Closed-form solutions to the optimal precoders are derived using majorization theory and convex optimization techniques. We show that if there are constraints on receiver complexity, the proposed precoders can improve performance for large MIMO systems operating over slowly time-varying fading channels.