Throughput-Efficient Scheduling and Interference Alignment for MIMO Wireless Systems

Multipath fading is one of the primary factors for degrading the performance in a wireless network. Information theoretic and past research suggest the use various diversity techniques to combat fading in wireless networks. Antenna diversity, a form of diversity technique, when incorporated in a wireless transceiver increases the system capacity and is one of the effective methods to combat fading in wireless systems. Also, recent research by Laneman et.al., Sendonaris et.al. suggests that cooperation among users in a wireless networks is an effective approach for a better signal reception in multipath fading environments. The diversity gains obtained by cooperation among the users of a wireless network is termed as cooperative diversity . Although, prior research in cooperative diversity considers users equipped with single antenna, in practical scenarios users may be able to accommodate multiple antennas due to the recent advanced research in semiconductor industry. Hence, the primary purpose of this thesis is to design, simulate and analyze an end-end performance of multi-antenna wireless systems employing cooperative multi antenna relay nodes so as to exploit the cooperative diversity and antenna diversity simultaneously in a wireless networks. Three main contributions to the area of cooperative multiple-input multiple-output (MIMO) wireless systems is presented in this thesis. First, we perform information theoretic analysis to study the impact of antenna arrays on cooperative wireless networks and propose the best possible distribution of antenna arrays among the three terminals of a simple three terminal cooperative relay network. Second, we design, simulate, and analyze a cooperative multiple-input multiple-output (MIMO) wireless systems employing orthogonal space-time block codes as proposed by Alamouti in 1998 with a decode-and-forward (DF) relay terminal. We implement a maximal ratio combining receiver that provides almost twice the diversity gain with respect to point-point multiple input multiple output link. Finally, we implement a practical receiver for cooperative reception using multiple antennas at all nodes based on Bell-Labs Layered Space Time architecture (BLAST). We incorporate a practical adaptive decode-and-forward (DF) relaying technique for reliable signal retransmission for both Alamouti space-time coding and the BLAST schemes. Results presented in terms of bit error rates and throughput show that remarkable performance gains are achievable by combining the concepts drawn from space-time coding, cooperative relaying and array processing.

After a few decades’ evolution of wireless communication systems, to ensure reliable highspeed communication over unreliable wireless channels is still one of the major challenges facing researchers and engineers. The use of multiple antennas at transmitter and receiver, known as multiple-input multiple-output (MIMO) communications, is one promising technology delivering desired wireless services. The main goal of this thesis is to study two important issues in wireless MIMO communication systems: receiver design for coded MIMO systems, and diversity-multiplexing tradeoff analysis in general fading channels. In the first part of this thesis, we decompose the receiver design problem into two subproblems: MIMO channel estimation and MIMO detection. For the MIMO channel estimation, we develop an expectation-maximization (EM) based semi-blind channel and noise covariance matrix estimation algorithm for space-time coding systems under spatially correlated noise. By incorporating the proposed channel estimator into the iterative receiver structure, both the channel estimation and the error-control decoding are improved significantly. We also derive the modified Cramer-Rao bounds (MCRB) for the unknown parameters as the channel estimation performance metric, and demonstrate that the proposed channel estimation algorithm can achieve the MCRB after several iterations. For the MIMO detection, we propose a novel lowcomplexity MIMO detection algorithm, which has only cubic order computational complexity, but with near-optimal performance. For a 4×4 turbo-coded system, we show that the proposed detector had the same performance as the maximum a posteriori (MAP) detector for BPSK modulation, and 0.1 dB advantage over the approximated MAP detector (list sphere decoding algorithm) for 16-QAM modulation at BER = 10−4. In the second part of this thesis, we derive the optimal diversity-multiplexing tradeoff for

The capacity of multiple-input multiple-output (MIMO) wireless communication systems over spatially correlated Rayleigh distributed flat fading channels with complex Gaussian additive noise is investigated. Specifically, the probability density function of the mutual information between transmitted and received complex signals of MIMO systems is derived. Using this density the closed-form ergodic capacity (mean), delay-limited capacity, capacity variance and outage capacity formulas for spatially correlated channels are derived and then these formulas are evaluated numerically. Numerical results show how the channel correlation degrades the capacity of MIMO communication systems. It is also shown that the density of mutual information of correlated/uncorrelated MIMO systems can be approximated by a Gaussian density with derived mean and variance, even for a finite number of inputs and outputs.

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

Spatial correlation is a crucial impairment for practical Multiple Input Multiple Output (MIMO) wireless communication systems. It is important to consider spatial correlation between antennas in actual communication scenario at both sides, i.e. transmit and receive side. Furthermore, we have considered nonorthogonal full rate STBC in MIMO systems equipped with four transmit antennas and four receive antennas in a quasi-static Rayleigh fading channel. In this paper, Bit Error Rate (BER) performance of full rate non-orthogonal Space Time Block code (STBC) is obtained using simulations in MIMO wireless communication systems. Spatial correlation is assumed between antennas at both the transmitter and the receiver sides. For this analysis, we have considered various transmit antenna spacing values of d t = 0.1π, 0.2π, and 0.4π keeping fixed d r = 0.1π and various receive antenna spacing values of d r = 0.1π, 0.2π, and 0.4π keeping fixed d t = 0.1π. The obtained results show that the transmitting diversity is more serious than the receiving diversity in the spatially correlated antenna environment for the specified signal-to-noise ratio. This study will be useful for actual wireless communication implementation where spatial correlation antennas are present in the practical environment of the MIMO wireless communication system.

Nonlinearities play an imperative role in performance of wireless communication systems. In this paper, High Power Amplifiers (HPA) have been used to check the performance of the proposed system by analyzing its amplitude, phase and their joint distortions using Multiple-Input Multiple-Output (MIMO) wireless communication system. This paper takes-in account the overall effects of HPA that provokes nonlinearities at the transmitter's end in a communication system. Therefore, a novel method for the HPA nonlinearities mitigation has been proposed to improve the performance of amplitude, phase and joint distortions in MIMO communication systems. The simulation results show an improvement in the overall effect of the MIMO system and enhance the input response on the transmitter side. Furthermore, this method has been proposed to exploit the benefits of the MIMO system to improve the Symbol Error Rate (SER) versus Signal to Noise Ratio (SNR) curves for amplitude, phase and their joint distortions.

Multiple transmit-receive antenna based wireless communication system is a well investigated area in the literature. However, within the scope of author’s knowledge there are few analytical frameworks which facilitate communication system design engineers to select the required transmit-receive antenna combination for a given quality of service (QoS) in terms of Bit Error Rate (BER) or Symbol Error Rate (SER). Most of such frameworks for Multiple-Input Multiple-Output (MIMO) wireless systems in the existing literature are lacking tightness between theoretical approximation and actual simulation results. The aim of investigation in this study is to provide theoretical expectation of receiver performance with MIMO wireless communication system within a given channel. In this study, new analytical performance bound frameworks with tighter lower bounds have been presented for different receivers for MIMO systems. On the basis of the presented analytical framework, a simulation platform has been established. The channel state information as well as expected quality of service is assumed to be known for simplicity. Rayleigh fading channel has been considered within simulation platform. Simulation results show that the proposed frameworks provide degree of tightness up to 100 times at Signal to Noise Ratio (SNR) 20 dB for (2x2) MIMO system in comparison to the existing frameworks. Few other MIMO antenna combinations have been considered in the evaluation process of the proposed framework.

Tensor space–time (TST) coding for MIMO wireless communication systems

In conventional ways of fast responding and high performing model predictive control using Field Programmable Gate Arrays (FPGA), the approaches developed are applicable only to Single Input Single Output System (SISO). Many real time systems are Multiple Input Multiple Output (MIMO) systems and loop interaction is a major concern and has to be reduced in control of MIMO systems. Also, direct digital control with ability to solve the Quadratic Programming (QP) problem online, which can be applied to complex systems with fast response time and/or embedded applications and with limited computational resource for supervisory control approach, is required in many complex industrial MIMO systems. A novel direct digital control of Model predictive controller with FPGA for a MIMO system which considers and reduces loop interaction and which can also be implemented with very less investment is proposed here. The system was modeled from first principles and then simulated in Labview environment for MIMO system. Implementation of the system and response was verified for a stirred tank system. The proposed system has good performance in terms of reduction in loop interaction which is a major concern in implementation of controller for MIMO systems. Also, direct digital control of MIMO system instead of supervisory control was accomplished.

Independent component analysis for multiple-input multiple-output wireless communication systems

Traditional receiver algorithms developed for multiple-input multiple-output (MIMO) wireless communication systems are based on the assumption that the channel state information (CSI) is perfectly known at the receiver. However, in real environments the exact CSI is unavailable. In this paper, we address the problem of robustness of multiuser space-time block coded MIMO systems against imperfect CSI and develop a simple linear receiver which guarantees robustness against CSI errors with a certain selected probability. The proposed receiver is formulated via a probability-constrained optimization problem which is further relaxed using Chebyshev inequality to a much simpler second-order cone programming (SOCP) problem. Simulations demonstrate that the proposed receiver has a moderate performance degradation as compared to the exact solution to the original probability-constrained optimization problem, while offering much simpler implementation.

We present a hybrid soft detector that has a good performance/complexity trade-off for a multiple-input multiple-output (MIMO) wireless communication system with known channel information. The new soft detector combines the merits of a simple unstructured least-squares (LS)-based soft detector and a list sphere decoder (LSD)-based soft detector for data bit detection. The former is computationally much more efficient than the latter at the cost of poorer performance. The poor performance of the former occurs mainly when the channel matrix is ill-conditioned. Whenever this happens, we use the LSD-based soft detector in the hybrid soft detector; otherwise, we use the LS-based one. Moreover, we provide a tight radius for a sphere decoder, a hard detector, via using the output of an LS-based hard detector. These two hard detectors are needed to determine if LS or LSD should be used in the hybrid soft detector. As an application example, we consider doubling the maximum data rate of the IEEE 802.11a conformable wireless local area networks by a MIMO system with two transmit and two receive antennas. For this application, the new soft detector is about 10 times faster than the LSD-based one and is about 10 times slower than the LS-based one. Yet the packet error rate due to using the new soft detector is quite close to that of using the LSD-based one.

Symbol decoding in multiple-input multiple-output (MIMO) wireless communication systems requires the deployment of fast, energy-efficient computing hardware deployable at the edge. The brute-force and exact maximum likelihood (ML) decoder, solved on conventional classical digital hardware to decode MIMO symbols, has exponential time complexity. Approximate classical solvers implemented on the same hardware have polynomial time complexity at the best. In this article, we design an alternative ring-oscillator-based coupled oscillator array (also known as oscillatory neural network (ONN)) to act as an oscillator Ising machine (OIM) and heuristically solve the ML-based MIMO detection problem. Complementary metal oxide semiconductor (CMOS) technology is used to design the ring oscillators, and ferroelectric field effect transistor (FeFET) technology is chosen as the non-volatile memory (NVM) coupling element (X) between the oscillators in this CMOS + X OIM design. For this purpose, we experimentally report high linear range of conductance variation (1 µS to 60 µS) with programming voltage pulses in a HfO 2 -based FeFET device fabricated at 28 nm high-K/ metal gate (HKMG) CMOS technology node. We incorporate the conductance modulation characteristic in SPICE simulation of the ring oscillators connected in an all-to-all fashion through a crossbar array of these FeFET devices. We show that the above range of conductance variation of FeFET is suitable to obtain best OIM performance, thereby making FeFET a suitable NVM device for this application. Our SPICE simulations show that there is no significant performance drop for symbol detection up to MIMO array sizes of 90 transmitting and 90 receiving antennas. Our simulations, combined with analytical treatment using Kuramoto model of oscillators, predict that this designed classical analog OIM, if implemented experimentally, will offer logarithmic scaling of computation time with MIMO size, thereby offering huge improvement (in terms of computation speed) over exact and approximate classical solvers run on conventional digital hardware.

Multiple-Input Multiple-Output (MIMO) systems that realize high-speed data transmission with multiple antennas at both transmitter and receiver are drawing much attention. In line-of sight (LOS) environments, the performance of MIMO systems depends largely on the difference of the phase difference of direct paths from transmit antennas to each receive antenna. When the phase difference of direct paths are close to each other, the spatial division multiplexing (SDM) channels are not orthogonal to each other so signal detection becomes difficult. In this paper, we propose a MIMO system with relative phase difference time-shift modulation (RPDTM) in Rician fading environments. The proposed scheme transmits independent signals from each antenna at each time slot where the relative phase difference between signal constellations used by transmit antennas varies in a pre-determined pattern. This transmission virtually changes the phase difference of direct paths from transmit antennas to each receive antenna without lowering data rate and without knowledge of the channels. In addition, forward error correction coding (ECC) is applied to exploit the time slots where the receiver can detect the signals easily to improve the detection performance. If there are time slots where the receiver can separate the received signal, the receiver can decode the data by using the time slots and the correlation between data. From the results of computer simulation, we show that MIMO system with RPDTM can achieve the better bit error rate (BER) than the conventional MIMO system. We also show that the MIMO system with RPDTM is effective by about Rician factor K=10dB.

Consider a multiple input multiple output (MIMO) system with pulse amplitude modulation (PAM), where each transmit antenna is allowed to choose a different transmission delay. (We refer to this system as a MIMO system with asynchronous PAM.) Such MIMO systems have been studied before for increasing diversity and avoiding unintentional beamforming. We quantify the capacity/outage capacity improvement due to asynchronism and the corresponding spectral leakage (if any) for MIMO point-to-point and MIMO broadcast channels. We show that under commonly used transmitter spectral mask constraints, the channel has unbounded degrees of freedom. Synchronous PAM exploits only a finite number of these degrees of freedom, and asynchronism helps to improve capacity. For most cases of interest, two distinct shifts attain most of the capacity improvement. These gains are robust to interference from adjacent carriers. Analysis of the spectrum of the asynchronous PAM suggests that optimal water-filling based schemes are useful for improving capacity only in directional links due to possible spectral leakage, while uniform power allocation leads to capacity improvement without any extra spectral leakage.