Indoor Location Position Based on Bluetooth Signal Strength

The location method based on Received Signal Strength Indication (RSSI) ranging has the advantages of low development cost and simple implementation mechanism, and is the mainstream indoor location method nowadays. However, at present, there is a lack of systematic research on the characteristics of Access Point (AP) received signal strength, which cannot meet the signal strength characteristics required by specific indoor positioning environment. Detailedly, in this study, the indoor distribution characteristics of 2.4 GHz RSSI were analyzed experimentally from three influencing factors including antenna orientation of the receiver, type of wireless network card of the receiver and height difference of the transmitting and receiving antenna. The experimental results show that: (1) The RSSI value measured is the strongest When the antenna of the receiver is vertically oriented to the antenna of the transmitter, while the antenna is vertically backward to the transmitter, it is the opposite. The difference between the strongest signal and the weakest signal is 20%–25% at the same test point. (2) The network card with a large measurement range should be selected for data collection on the premise that the quantization step size is 1 and the smoothness is small. Avoiding using the network card for positioning with the maximum limit of measurement range is proposed also. (3) The path loss index of the ranging model is affected by the height difference of the antenna, resulting in a deviation of 0.1–0.2.

Received Signal Strength Indicator (RSSI) is used in indoor positioning for measuring object distance to the base station. However, acquiring accurate RSSI values is challenging because wireless interference factors, such as multipath decline interference, make RSSI values of the same object fluctuate over time. Therefore, instead of a single RSSI, RSSI acquisition will collect a set of RSSI values from which the most moderate RSSI is derived. For this purpose, we propose an Enhanced Gaussian Mixture Model (EGMM) to derive a more precise RSSI for improving indoor positioning accuracy. EGMM enhances Gaussian Mixture Model (GMM) by applying Akaike information criterion (AIC) to determine the best K value for GMM to divide RSSI values into K sets representing signals from different paths. Then, EGMM identifies the most appropriate set of RSSI values to derive a more precise RSSI and thus improves the accuracy of indoor positioning. Our EGMM solution performs well in an open indoor space. The experiment is conducted with iBeacon devices, and the average error distance of EGMM is about 64% of those generated by existing Gaussian filtering. The average positioning error of EGMM is about 0.48 meter, which is adequate to indoor positioning accuracy.

As WiFi technology becomes more widespread and integrated, precise location tracking within complex indoor environments is gaining significance in contemporary public spaces.Nevertheless, challenges persist in indoor scenarios, including issues such as noise and multi-path effects stemming from the degradation of the Received Signal Strength Indicator (RSSI). Additionally, obstacles causing signal shading contribute to a decrease in the accuracy of indoor location tracking. Within this paper, we introduce an innovative indoor localization algorithm termed Vision Transformer Indoor Localization (VTIL). This algorithmleverages RSSI and Vision-Transformer (ViT) technologies to enhance indoor positioning accuracy. Initially, the RSSI fingerprints undergo normalization by scaling them to the maximum and minimum values. To mitigate the impact of noise and irrelevant features, the Principal Component Analysis (PCA) algorithmis then employed for effective feature extraction.Secondly, the RSSI fingerprint library is converted into an RSSI gray image library. Then the RSSI gray image is divided into several small blocks, and the position-coding input is performed in the form of a sequence. The ViT model divides the weight ratio of each block in the RSSI image to alleviate the impact of multi-path effects. According to the experimental results using public datasets, our approach achieves a noteworthy 37.26% reduction in the average distance estimation error when compared to existing indoor fingerprint localization algorithms.

Indoor localization can provide a number of different services such as location-aware advertisement, indoor navigation and automating different appliances based on the user location. A number of different techniques such as time-difference- of-arrival, angle-of-arrival, time-of-flight, and received signal strength indicator (RSSI) have been used to provide Location Based Services (LBS). RSSI is one of the widely used methods as it is cost efficient and easy to implement. However, RSSI's performance is limited by multipath fading and indoor noise. Particle Filter (PF) is an accurate Bayesian Filtering algorithm that can improve the performance of RSSI-based indoor localization. However, PF is not able to satisfy the high accuracy requirement (possibly 10cm) of indoor localization. In this paper, we present Particle Filter-Extended Kalman Filter (PFEKF) cascaded algorithm that combines PF and EKF in series to reduce the impact of multipath effects and noise on the RSSI. Our experimental results show that PFEKF improves the localization accuracy by 31.3% and 33.9% in 3D and 2D environments respectively when compared with using only a PF.

An indoor localization system in wireless sensor networks has become a hot development area. Received signal strength indicator (RSSI)-based localization is a promising technique since it requires a relatively low configuration, battery power and easy control. However, the received signal strength is influenced by channel interference and propagation environments. This characteristic affects channel stability and location accuracy in RSSI-based localization. As a result, we propose a novel indoor localization system consisting of a preprocessing method and a post-processing method. To improve channel stability, the pre-processing method selects an optimal channel in terms of the smallest distance error. The optimal channel is less affected to IEEE 802.11. To develop location accuracy, the post-processing method performs maximum likelihood estimation-based location tracking scheme considering the reliability of the RSSI value measurement. We apply three methods to the existing MLE to improve the reliability of the RSSI value. By using this indoor localization system with preprocessing and post-processing, the location error can be reduced. We also proved the performance of the indoor localization system by conducting experiments in a real indoor environment.

Towards a better indoor positioning system: A location estimation process using artificial neural networks based on a semi-interpolated database

This paper describes research towards a system for locating wireless nodes in a home environment requiring merely a single access point. The only sensor reading used for the location estimation is the received signal strength indication (RSSI) as given by an RF interface, e.g., Wi-Fi. Wireless signal strength maps for the positioning filter are obtained by a two-step parametric and measurement driven ray-tracing approach to account for absorption and reflection characteristics of various obstacles. Location estimates are then computed using Bayesian filtering on sample sets derived by Monte Carlo sampling. We outline the research leading to the system and provide location performance metrics using trace-driven simulations and real-life experiments. Our results and real-life walk-troughs indicate that RSSI readings from a single access point in an indoor environment are sufficient to derive good location estimates of users with sub-room precision.

At present, the theory and algorithm of wireless indoor positioning systems have been widely researched. Some applications of these systems have been successfully used such as inventory management. Nevertheless, positioning using radio signals indoor is subject to multipath propagation and other causes. Therefore, how to determine the location accurately has been recognized as a difficult task. This paper focuses on one of the positioning methods called received signal strength indication(RSSI) in a Wireless Local Area Network(WLAN). To improve the positioning accuracy, we proposed a scheme which to estimate the distance between access point(AP) and mobile station(MS) using the average of pilot signal strength in frequency domain. We then propose another scheme to estimate the position of the MS based on the estimated distances. At last, the simulations results show that the proposed schemes has a higher degree accuracy compared with the conventional methods.

Indoor location-based mobile applications have been gaining momentum in reshaping the daily activities of Internet users. A large number of indoor localization techniques achieve the localization goal by analyzing the received signal strength indication (RSSI) of pervasive WiFi signals. Compared with RSSI, the channel state information (CSI) provides more comprehensive time and space information with more complex hardware and software cost. In this paper, we proposed two CSI-based indoor localization algorithms: 1) a localization algorithm based on the weighted linear discriminant analysis; 2) a localization algorithm based on two-dimensional principal component analysis. The experimental results show that the proposed algorithms outperform the basic Bayesian algorithm based on the principal component analysis on improving the localization accuracy and reducing the computational complexity.

Positioning services are increasingly used for applications such as navigation, advertising and social media. While outdoor navigation based on GPS and/or cellular systems works well, indoor navigation is a much tougher challenge. This paper proposes an indoor localization using Wi-Fi received signal strength indicator (RSSI) measurements from existing access points. Using RSSI data from multiple access points, additional access points will be added in the system thru linear regression statistical model to create virtual access points (VAPs). This paper fuses the low-cost and flexible system of fingerprint localization with VAP creation and the improvement in accuracy by adapting Kalman Filter (KF) and Particle Filter (Pf). The effectiveness of using KF with VAP has demonstrated positive results in previous research. This paper aims to integrate the use of PF in the system. To improve the performance of indoor localization, the proposed model will be an improved virtual access point localization, proposed filtering (VAP+KF+PF).

Nowadays, location awareness becomes the key to numerous Internet of Things (IoT) applications. Among the various methods for indoor localisation, received signal strength indicator (RSSI)-based fingerprinting attracts massive attention. However, the RSSI fingerprinting method is susceptible to lower accuracies because of the disturbance triggered by various factors from the indoors that influence the link quality of radio signals. Localisation using body-mounted wearable devices introduces an additional source of error when calculating the RSSI, leading to the deterioration of localisation performance. The broad aim of this study is to mitigate the user’s body shadowing effect on RSSI to improve localisation accuracy. Firstly, this study examines the effect of the user’s body on RSSI. Then, an angle estimation method is proposed by leveraging the concept of landmark. For precise identification of landmarks, an inertial measurement unit (IMU)-aided decision tree-based motion mode classifier is implemented. After that, a compensation model is proposed to correct the RSSI. Finally, the unknown location is estimated using the nearest neighbour method. Results demonstrated that the proposed system can significantly improve the localisation accuracy, where a median localisation accuracy of 1.46 m is achieved after compensating the body effect, which is 2.68 m before the compensation using the classical K-nearest neighbour method. Moreover, the proposed system noticeably outperformed others when comparing its performance with two other related works. The median accuracy is further improved to 0.74 m by applying a proposed weighted K-nearest neighbour algorithm.

A new era of ubiquitous indoor location awareness is on the horizon especially for context sensing, ambient assisted living and many other smart city applications. Although indoor localization plays a pivotal role in making the environment smarter, it is still very difficult to compare state-of-the-art localization algorithms due to the scarcity of standard databases. Publicly available databases are neither fine-grained nor contain data for different conditions. Received Signal Strength Indicator (RSSI) of Wi-Fi signals vary with indoor environment (open/closed room, presence/absence of user, temperature etc.) and scanning smart hand-held devices. Thus, localization accuracy varies with various environmental conditions and also granularity of location points (cell). Consequently, in this paper, our contribution is two-fold. First, we present a comprehensive indoor localization dataset, subject to different domains-spatial, temporal, context and device. RSSI data has been collected with cell sizes as small as $$1\,{\mathrm{m}}\times 1\,{\mathrm{m}}$$ from three floors of a building of our University using an Android application built for this purpose. This multi-floor dataset is available online at https://drive.google.com/open?id=1_z1qhoRIcpineP9AHkfVGCfB2Fd_e-fD. Our experimental results show that maximum of $$71.78\%$$ classification accuracy can be achieved for state-of-the-art classifiers when training and testing samples are taken in different environmental conditions and from smartphones having different configurations. Single classifier cannot easily be modified to suit these variations without loosing its generality. So, to overcome these conditional dependencies, our second contribution is to propose a framework for indoor localization, JUIndoorLoc and design an ensemble of condition specific classifiers as part of the framework to take care of context and device heterogeneity. Consequently, this ensemble of condition specific classifiers is implemented and found to predict a location with $$91.74\%$$ accuracy (1.87 m) for our dataset.

Indoor localization techniques using Received Signal Strength Indicator (RSSI) is attractive in the Internet of Things domain due to its simplicity and cost-effectiveness. However, there are many different approaches proposed in and there is not a common, widely acceptable solution in the research community. This is mainly due to the limited number of publicly available datasets and that the multi-effect signal phenomenon limits each dataset to its gathering testbed. In this paper, we tested several fingerprinting methods in a publicly available dataset and we compared them against the RSSI regression approach, which is considered as the most prominent one in certain domains, such as indoor and outdoor localization.

Nowadays, location-based services are common in our daily lives. Traditional Global Positioning System (GPS) location can provide real-time location function in outdoor complex environments, but it is insufficient for indoor location. There are many indoor location technologies, such as ultrasound, Zigbee, RFID and WIFI. RFID location technology has attracted the attention of researchers due to its high precision and low cost. Most existing RFID location algorithms are based on RSSI (Received Signal Strength Indicator) measurement. When converting RSSI to distance, the inaccurate estimation of the path loss parameter may lead to large error. In order to reduce the deviation, this paper proposes a new RFID location algorithm. Specifically, the RSSI of the target tag is read in different directions of the antenna, and the position information is predicted by the general regression neural network, which is optimized by the optimization algorithm. The experimental results show the efficiency of our proposed algorithm.

D-Log: A WiFi Log-based differential scheme for enhanced indoor localization with single RSSI source and infrequent sampling rate