Modeling and simulation of mixed modulation formats for improved CDMA bandwidth efficiency

With the rapid development of Global Navigation Satellite Systems (GNSS). The binary offset carrier (BOC) signal was proposed to separate new navigation signal from traditional BPSK in frequency and it has better accuracy and anti-multipath performance compared with the BPSK of the same code rate. But the ambiguity caused by the multi-peaks of auto-correlation function makes traditional acquisition technique not applicable to BOC.A novel unambiguous acquisition algorithm for sine BOC signals is proposed in this paper. There are two types of local reference signals: the BOC signal and a designed binary auxiliary signal. They are both correlated with the received signals. Then, a correlation function unambiguous for acquisition of BOC signal is obtained by multiplying the two correlation results. In the acquisition stage of BOC(10,5), the detection probability of the proposed method is approximately 1.5 dB better than that of GRASS and 2 dB better than that of SPAR. For BOC(14,2), the detection probability advantages of the proposed method increase to 6 dB and 7.5 dB . In conclusion, the proposed method can eliminate ambiguity and has significant performance advantages compared with the above methods.

Binary offset carrier (BOC) signal synchronization is based on the correlation between the received and locally generated BOC signals. Thus, the multiple side-peaks in BOC autocorrelation are one of the main error sources in synchronizing BOC signals. Recently, a new correlation function with no side-peaks was proposed for sine or cosine phased BOC signal synchronization by the authors [7]. In this paper, we propose a novel correlation function for composite binary offset carrier (CBOC) signals by using the similar method to that in [7], which has a better power ratio than the CBOC autocorrelation.

Binary Offset Carrier (BOC) modulation technology is gradually replacing the traditional BPSK modulation signal as the main modulation method of the new generation satellite navigation signal due to its superiority in multipath suppression performance and code tracking accuracy. However, the tracking and mis-locking problem of BOC signals has become a key point limiting the widespread application of BOC signals. In this paper, we use code reference waveform (CCRW) technology and optimized Bump-jump (BJ) algorithm to analyze the multipath performance of low-order BOC signals under five code reference waveforms. Aiming at the high peak BOC signal with many peaks and high peak-to-peak ratio, we propose a new code reference waveform ensures the high-order BOC signal has good anti-multipath performance and solves the problem of extremely easy mis-locking of its receiver.

Multipath is a dominant source of positioning errors in global navigation satellite system receivers. It is difficult to design multipath mitigation techniques for binary offset carrier (BOC) signals due to the complicated autocorrelation function of BOC signals and localized variations of multipath. In this paper, a dual high resolution correlators (DHRC) technique is proposed for BOC signals to mitigate code and subcarrier multipath errors, as well as the carrier multipath error that is neglected by common techniques. Based on the concept of dual binary phase-shift keying (BPSK) tracking, the BOC signal is decomposed into two BPSK signals located in the upper and lower sidebands, respectively, thereby transforming the multipath mitigation in the BOC signal into the multipath mitigation in the upper and lower sidebands. Two narrow correlation functions of the upper and lower sidebands are synthesized using multiple correlation values, so the multipath outside the main peak of the synthesized correlation function is eliminated. The peak value of the synthesized correlation function is reduced from the original ACF, resulting in a large noise error. Therefore, a complementary filter is designed to compensate the noise error. Theoretical analysis and simulation results demonstrate that the DHRC technique with complementary filters can significantly mitigate multipath errors for BOC signals with slight thermal noise performance loss.

The long PN code in a Binary Offset Carrier (BOC) modulated signal has a higher rate than the GPS C/A code, which makes the acquisition process in the new global navigation satellite system (GNSS) much more complex.To achieve a fast acquisition of the GNSS signal with a reduced number of correlators and low computational complexity, a two-stage deterministic compressed (DS) GNSS acquisition technique has been proposed.Nevertheless, the ambiguous threat of BOC signal isn't taken into account in the DS technique.To eliminate the ambiguity threat in the acquisition process of BOC (m, n) signal, an unambiguous deterministic compressed acquisition is proposed in this paper.The main idea of the proposed technique is to introduce a simplified GRASS algorithm in the second stage measurement.Theoretical analysis and simulation results show that, at the expense of some performance degradation the proposed technique can completely remove the undesired positive side peaks of BOC (m, n) signal, and reduce the chance of false peak acquisition compared with the DS technique.

The present paper deals with design and development of a generalized parametrizable modulator (GPM) that can perform Gaussian minimum shift keying (GMSK) modulation and Quadrature Phase Shift Keying (QPSK) modulation in a reconfigurable baseband modulator for software defined radio (SDR) architecture. GMSK is the underlying modulation scheme for the Global System for mobile (GSM) standard, while QPSK technique is the basic modulation scheme for Code Division Multiple Access (CDMA) standard. Although GMSK is an inherently non-linear modulation technique, the present work uses a linearly approximated GMSK technique to take the advantage of the simplicity of the filter structure. The normalised error in amplitude as a function of modulation index and bandwidth time product has been simulated. The proposed GPM is capable of working at a maximum data rate of 13.75 Mbps, thus satisfying the requirements of almost all 2G and 3G air interface standards. The GPM can perform QPSK using four pulse shaping filters, two Raised Cosine (RC) filters and two Root Raised Cosine (RRC) filters. The proposed GPM architecture is implemented on a Spartan 3E starter kit.

Traditional group delay measurement methods include single carrier phase method and spectrum analysis method based on signal autocorrelation function, but these two methods have their own limitations in GNSS receiver group delay measurement. The single carrier phase method cannot measure the group delay of multi filters and downconverters stage connect channel directly, and the measurement accuracy of group delay of spectrum analysis method based on signal autocorrelation function will deteriorate greatly near the zero point of signal power spectrum. In order to solve the above problems, this paper proposes a BOC (bi-nary offset carrier) signal group delay measurement method, which can realize the simple and accurate measurement of GNSS receiver group delay. In this paper, a group delay measurement method is analyzed and simulated by software, and verifies the feasibility and accuracy of the method are verified by simulation.KeywordsBOC navigation signalGroup delayGNSS receiver

The recent researches on the tracking of binary offset carrier (BOC) modulated signals have been studied focusing onresolving the ambiguity problem caused by the multiple side-peaks in BOC autocorrelation. In this paper, we proposea novel unambiguous BOC tracking scheme with an improved tracking performance by using partial-pulses of BOCsignals. Firstly, we observe that a sub-carrier consists of two partial rectangular pulses referred to as partial-pulses,and then, generate multiple partial-correlations composing the BOC autocorrelation. Finally, a correlation function withno side-peak is constructed by combining the partial-correlations, and then, a delay lock loop employing the proposedunambiguous correlation function adjusts the phase of the local BOC signals. From numerical results, it is confirmedthat the proposed scheme provides a better tracking performance than the conventional schemes in terms of thetracking error standard deviation.

The optimized design of the spreading modulation technique is considered to be the major way to achieve both spectrum compatibility and performance improvement. To allow a variety of signals to share the limited frequency band of GNSS and further improve the signals’ ranging accuracy and anti-interference performance, several new spreading modulation techniques have been proposed in recent years. In this chapter, we will introduce a variety of typical spreading modulation techniques such as BPSK with rectangular chips (BPSK-R), binary offset carrier (BOC), binary coded symbol (BCS), composite BCS (CBCS), time-multiplexed BOC (TMBOC), composite BOC (CBOC), quadrature multiplexed BOC (QMBOC), as well as alternative BOC (AltBOC). The processing ambiguity threat of BOC and MBOC signals and possible solutions are also discussed. Considering that in the next-generation GNSS implementations, new requirements and new constraints will constantly emerge and new modulation methods will be needed, this chapter is not meant to be regarded as a review of the development of navigation signal modulation technology, or an interpretation of the signal formats being used by several major satellite navigation systems. Instead, we regard the spreading modulations used in satellite navigation signals as general techniques and focus our discussion on the principles of these modulation techniques and the design ideas behind their generation processes.

The binary offset carrier (BOC) modulation was initially developed for easy sharing of spectrum between GPS modernization signals and legacy binary phase shift keying (BPSK)-modulated signals in the same band. It is now adopted by all GNSS constellations as a BOC signal has a larger Gabor bandwidth, producing better ranging (accuracy and multipath) performance. However, general BOC signal acquisition and tracking encounters the problem of multiple peaks (less an issue for MBOC, though), and many methods have been proposed to address this issue. A simple method to avoid such an ambiguity is to extract the upper and lower sidebands of the split spectrum of a BOC signal, treat them separately as a BPSK signal each, and then combine the results so as to recover the reduced sideband signal strength. Coherent combining is more gainful than the noncoherent counterpart particularly when the incoming signal is weak and/or when a strong interference signal is present. In this paper, a long coherent combining and integration (LCCI) scheme is presented, which enables standalone acquisition of a BOC signal without external aiding from a network or an inertial navigation system (INS) under combined narrowband and matched spectral interference signals. The LCCI scheme burns through the strong interference via building up the desired signal while averaging out noise and interference. To build up the desired signal, it makes use of all information resources available (e.g., L1 and L2, upper and lower sidebands, odd and even chips, and/or I and Q components) and applies coherent combining and long coherent integration, followed by non-coherent accumulation if necessary. Issues and enabling techniques are presented in this paper. The LCCI scheme is implemented on a software defined receiver (SDR) platform consisting of FPGA and ARM. Results of real-time demo with input RF signals generated by a Spirent GPS Simulator are described in the paper.

It is well known that code and carrier-phase multipath, which has been under study for over two decades, is the limiting error sources in high-precision differential GPS applications. In virtually every study, however, the effects of autocorrelation function are considered little. This article focuses on the bounds of code and carrier-phase multipath error in terms of GNSS (Global Navigation Satellite Systems) signals autocorrelation functions, which result from a fundamental theoretical description and mathematical modeling of GNSS receiver. Firstly, an overview of the characteristics of the BOC (Binary Offset Carrier) signal ACF (autocorrelation function) is given in the paper. The impact on the DLL (delay-lock loop) and PLL (phase lock loop) discriminator functions are derived in the followed section and consequently a general description of multipath errors are obtained for the BOC signals. This quantifies the influence of limited bandwidth on receiver tracking error due to multipath. Finally, the simulation results show a distinct change in the error envelope for BOC signals from which has been got using current GPS C/A code signal.

The global navigation satellite system (GNSS) signal modulation type plays a crucial role in determining the performances of positioning, navigation and timing (PNT) services. Currently, the binary offset carrier (BOC) modulation signal and binary coded symbol (BCS) modulation signal are both bipolar signals, which greatly restrict the room of improving the GNSS signal performance. Therefore, multi-level coded symbol (MCS) modulation has received great attention in the field of GNSS signal design. The MCS modulation is the most extensive step-coded symbol modulation mode, where BOC modulation and BCS modulation are its special cases. Since the waveform symbol of the MCS modulation signal can be arbitrarily valued, the optimal GNSS signal can be designed. However, like the BOC modulation signal, the MCS modulation signal also has the problem of ambiguous tracking, and then results in a large pseudo range measurement error, which is unacceptable for the new generation GNSS with high accuracy. In recent years, the unambiguous tracking of GNSS signals has become a hot research subject in the navigation signal processing domain and many methods are presented, and those methods can be divided into three categories:BPSK-like method, bump jump (BJ) method, and side-peak cancellation (SC) method. However, these methods are designed for BOC signal, and they are not suitable for MCS signal. Therefore, in this paper we propose a general unambiguous tracking algorithm based on the pseudo correlation function (PCF), which is suitable for MCS modulated signals. Firstly, the unitary expression of MCS modulated signal based on waveform value vector is given, then the unitary formula of cross-correlation function for MCS signal is derived and the definition of PCF is given. Then the constraint condition which should be satisfied to realize unambiguous tracking is analyzed in depth, and the universal constructing method of two reference signals and the relationship between each other are derived according to this constraint condition, which brings great convenience for solving the specific MCS signal. The code tracking loop model of GNSS receiver based on the proposed method is illustrated. It is observed that the proposed method can receive different MCS signals under the same receiver loop framework, and can simplify the design of the receiver while eliminating the tracking ambiguous problem. Finally, as a special case of MCS signal, the applications of the proposed method in four kinds of BOC signals are discussed respectively, and then the waveform value vector of the reference signal and the unitary expression of code discriminator are derived. Simulation results show that the proposed method can effectively solve the ambiguous tracking problem of MCS signal, which has good performance and broad application prospect.

Binary offset carrier (BOC) modulation signals have been widely adopted in global navigation satellite systems (GNSSs) such as Galileo and modernized global positioning system [1] [2]. Although this kind of modulation offers excellent performances, a main drawback of BOC modulation is that ambiguous acquisition and biased tracking for its multi-peak autocorrelation function (ACF). This article presents herein a novel acquisition technique allows removal of side peaks thoroughly and acquire better acquisition performance. This scheme is applicable to BOC (n, n) modulation signals. Theoretical analysis and system simulation demonstrate the algorithm proposed has better performance in acquisition aspect compared with other typical algorithms under the influence of additive white Gaussian noise.

As Gaussian minimum shift keying (GMSK) modulation scheme is adopted for wireless body area network (WBAN) applications, simple and noise-robust synchronisation algorithms for GMSK are desired to meet the limited resources of power, storage and size in WBAN. However, the current synchronisation algorithms for GMSK are either too complicated or have unsatisfactory performance for low signal-to-noise ratio (SNR), especially for coded GMSK systems. The authors will propose the synchronisation algorithms for general GMSK systems with three unknown synchronisation parameters, namely, timing, frequency and phase offsets estimation. By incorporating noise/interference-reduction methods, the authors propose low-complexity synchronisation algorithms for GMSK that can achieve satisfactory performance in low SNR region. Furthermore, their new feedforward timing and frequency recovery algorithms can provide much better performance than those in the literature by using reliability-measuring mechanism for timing estimation and two-phase frequency estimation. The data-aided Cramer–Rao bounds (CRBs) for the joint estimation of GMSK synchronisation parameters are also derived. The numerical results show that the performance of their proposed synchronisation algorithms is close to the CRBs. The overall bit error rate performance for both uncoded and Bose-Chaudhuri-Hocquenhem BCH-coded GMSK systems are examined. The performance loss owing to synchronisation errors can be reduced to about 1 dB with their proposed algorithms.

The WiMax (Worldwide Interoperability for Microwave Access) is a technology in<strong> </strong>broadband wireless access, which employs OFDM (Orthogonal Frequency Division Multiplexing) as an alternative transmission to enable high speed data in communication system. This research aim is to analyze the performance system of the OFDM-Based WiMAX, which used the cyclic prefix. The model was designed in four schemes of simulation method, the BPSK (Binary Phase Shift Keying, QPSK (Quadrature Phase Shift Keying), 16 QAM (Quadrature Amplitude Modulation) and 64 QAM. Each scheme was investigated BER (Bit Error Rate) on AWGN (Additive White Gaussian Noise) channel and multipath Rayleigh fading channel, which had applied the cyclic prefix. By simulation of the cyclic prefix was produced the modulation measurement of the BPSK, QPSK, 16 and 64 QAM. The performance result of Eb/No 15 dB was obtained the BER of BPSK and QPSK of 1.11E-11, the BER of 16 QAM and 64 QAM of 8.69E-06 and 0.00333 respectively. Those results indicated much smaller BER value than EbNo 0 dB which BPSK and QPSK of 1 BER, 1.5 and 1.75 BER for 16 QAM and 64 QAM respectively. In conclusion, a higher value of EbNo, hence the BER value would be lower.