Monitoring-based spectrum management for expanding opportunities of white space utilization

3G/4G wireless systems employed multiple antennas at both the transmitter and receiver offered significant gains over single-antenna systems. MassiveMIMO (MM) is one of the 5G technologies, which supports to increase the demand for high speed data, capacity, energy efficiency and spectral efficiency. It is known that space-time multiplexing and/or coding offer attractive means of combating fading and increases the capacity in a multi-antenna communication. In this paper, MM downlink scenario is considered. Performance analysis using conventional precoders like Matched Filter (MF), Zero Forcing (ZF), Regularized Beamforming (RBF) and Minimum Mean Square Error (MMSE) with Singular Value Decomposition (SVD) based balanced equalizer are studied in spatio-temporal environment. Signal to Interference Ratio (SINR) and Bit-Error Rate (BER) are used as performance measures. Monte-Carlo simulations are carried out to compute BER and SINR in MATLAB.

Multi-user detection (MUD) techniques are applied to the GPS interference suppression/rejection problem, such that recovery of GPS satellite signals out of an environment contaminated with one or more correlated interference sources is afforded. In modeling the narrowband digital interference as a set of multiple users it is shown that recovery is possible via any of several MUD algorithms, including the conventional detector, the decorrelating detector, the optimum linear detector, and the minimum mean square error (MMSE) detector. The relationship between the underlying structure of the GPS symbol (C/A code) and the performance of these detectors is studied such that bit error rate (BER) and signal-to-interference ratio (SIR) are developed analytically.

For the uplink interleaved single carrier frequency division multiple access (SC-FDMA) system, one of the main problems is that the multiple carrier frequency offsets (CFO), caused by Doppler shift in high-speed wireless communications, will cause severe inter-subcarrier interference (ICI), so as to influence the system performance. In this paper, we propose an effective multiple CFO compensation scheme, for reducing the ICI influence in the uplink interleaved SC-FDMA. On the one hand, the optimal CFO compensation value, which maximizes the signal-to-interference ratio (SIR), is achieved to compensate the CFO for each user at the receiver. On the other hand, the residual ICI is analyzed and an improved minimum mean square error (MMSE) frequency domain equalizer (FDE) receiver is developed which suppresses both ICI and noise. Theoretical analysis and simulation results show that the proposed CFO compensation scheme can effectively reduce the influence of ICI and im-prove the system performance.

We generalize the multiuser (CDMA spread spectrum) communication systems to the fading environments. We first extend Verdu's (1986) conventional optimum receiver to Rayleigh-fading environments and then evaluate its performance. Having no knowledge of the received power at the receiving end, we therefore need an estimator to efficiently estimate the received signal strength of each user in fading environments. A linear minimum mean square error (LMMSE) unbiased estimator is proposed to attain this goal. By using the minimum mean square error (MMSE) Bayesian estimation, we further propose the LMMSE bit estimator for efficient demodulation. Its performance is close to the optimum multiuser receiver but with a much simpler polynomial complexity. To further reduce the complexity, we extend the LMMSE estimator to the sequential LMMSE estimator. In sequential estimation, we do not need to implement the matched filter banks and to perform the matrix inversion when estimating. In addition, it converges after approximately 2k iterations, where k is the number of users. With this fast convergence property and the simple structure, the sequential LMMSE estimator provides an attractive alternative to the implementation of a multiuser system.

In present days, there has been a race among the communication systems in different schemes and generations. Gradually the transmission rate of data is increasing tremendously and breaking the previous generation's record. Now people are thinking of transmitting data beyond imagination. Using multiple antennas both at transmitter and receiver side, MIMO wireless technology efficiently provides very high spectral efficiency, boost the data transmission rate, enhance link reliability and improve system coverage. While transmitting data over mobile radio channels at high bit rates, the impulse response of the channel can be extended over a lot of symbol periods, leading fading and Inter-symbol interference (lSI). Equalizers are used to minimize Fading and interference effects. The analysis of the paper is studying the performance of Minimum mean square error method in terms of BER for MIMO (2×2) and (3×3) wireless channels. Binary Phase Shift Keying (BPSK) modulation technique was used in Rayleigh flat fading channel. Simulating in MATLAB results show that Minimum mean square error (MMSE) receivers is good for noise free channel and is successful in removing ISI. Successive interference method with optimal ordering outperforms the MMSE however a few problems arise because of iterative nature of the algorithm.

In orthogonal frequency-division multiplexing (OFDM) systems, it is generally assumed that the channel response is static in an OFDM symbol period. However, the assumption does not hold in high-mobility environments. As a result, intercarrier interference (ICI) is induced and the system performance is degraded. A simple remedy for this problem is the application of the zero-forcing (ZF) and minimum mean square error (MMSE) equalizers. Unfortunately, the direct ZF method requires the inversion of an NxN ICI matrix, where N is the number of subcarriers. When N is large, the computational complexity can become prohibitively high. As for the direct MMSE method, in addition to an NxN matrix inverse, it requires an extra NxN matrix multiplication, making the required computational complexity higher compared to the direct ZF method. In this dissertation, we first propose a low-complexity ZF method to solve the problem in single-input-single-output (SISO) OFDM systems. The main idea is to explore the special structure inherent in the ICI matrix and to apply Newton's iteration for matrix inversion. With our formulation, fast Fourier transforms (FFTs) can be used in the iterative process, reducing the complexity from O(N^3) to O(Nlog_2 N) . Also, the required number of the iteration is typically one or two. We also analyze the convergence behavior of the proposed method and derive the theoretical output signal-to-interference-noise-ratio (SINR). For the MMSE method, we first reformulate the MMSE solution in a way that the extra matrix multiplication can be avoided. Similar to the ZF method, we then exploit the structure of the ICI matrix and apply Newton's iteration to reduce the complexity of the matrix inversion. For a multiple-input-multiple-output (MIMO) OFDM system, the required complexity of the ZF and MMSE methods becomes more intractable. We then manage to extend the proposed ZF and MMSE methods for SISO-OFDM systems to MIMO-OFDM systems. It turns out that the computational complexity can be reduced even more significantly. Simulation results show that the performance of the proposed methods is almost as good as that of the direct ZF and MMSE methods, while the required computational complexity is reduced dramatically. Finally, we explore the application of the proposed methods in mobility-induced ICI mitigation for OFDM multiple access (OFDMA) systems, and in carrier frequency offset (CFO) induced ICI mitigation for OFDMA uplink systems. As that in OFDM systems, the proposed methods can reduce the required computational complexity, effectively.

Multiple-input multiple-output (MIMO) systems can achieve high data-rate and high capacity transmission. In MIMO systems, the scheme that weight substreams based on minimum mean square error (MMSE) criterion at the transmitter using feedback channel state information (CSI) achieves good performance (denoted hereafter as MMSE precoder). However, if the optimum number of substreams is not selected based on CSI and methods for reducing the performance degradation due to feedback delay is not used, MMSE precoder cannot achieve the full performance possible. In this paper, we propose an MMSE precoder with mode selection for MIMO systems, which selects both the number of substreams and the modulation scheme for each substream to minimize the average BER at a fixed rate. We evaluate the BER of the proposed MMSE precoder with two methods for reducing performance degradation due to feedback delay, channel prediction and receive weight robust to feedback delay. We also evaluate the BER of the proposed MMSE precoder with the method that combines channel prediction with receive weight robust to feedback delay. Simulation results show that the BER of the proposed MMSE precoder is improved compared to that of the conventional MMSE precoder using the fixed number of substreams. We also show that the method that combines channel prediction with receive weight robust to feedback delay can achieve good BER even when the large feedback delay exists.

In this paper, the minimum mean square error (MSE) convergence of the RBF equalizer is evaluated and compared with the linear equalizer based on the theoretical minimum MSE. The basic idea of comparing these two equalizers comes from the fact that the relationship between the hidden and output layers in the RBF equalizer is also linear. As extensive studies of this research, various channel models are selected, which include linearly separable channel, slightly distorted channel, and severely distorted channel models. The theoretical minimum MSE for both RBF and linear equalizers were computed, compared and the sensitivity of minimum MSE due to RBF center spreads was analyzed.

For the code division multiple access (CDMA) downlink channel, the chip-level equalization has been considered in this paper. There is no interference after despreading if all spreading codes are orthogonal, as in IS-95. However, it cannot be true for a frequency-selective fading channel. In this case, the chip-level equalization can be applied to restore the orthogonality. We investigate the chip-level equalization using finite impulse response (FIR) equalizers for the mobile station with multiple receive antennas. A blind approach and the minimum mean square error (MMSE) approach with code-multiplexed pilot are considered. A generalized MMSE equalization, which combines the MMSE and blind approaches together, is also investigated. It is shown that the generalized MMSE equalizer can effectively increase the number of samples to track the variation of channel and thereby performs better when the coherence time is small. In addition, we derive closed-form solutions of the blind, MMSE, and generalized MMSE equalizers for given channels.

Multiple user satellites monitor is an important technology which can improve both the monitoring network coverage and the capacity of multi-target signal processing. Multi user detection (MUD) is one of the key technology for multiple user satellites communication. In this paper, a new algorithm for MUD is implemented on field-programmable gate array (FPGA). This FPGA design is based on the minimum mean square error (MMSE) algorithm which consists of two main components: Matched filter and minimum mean square error matrix. Additionally, in order to conduct Monte Carlo simulation, we adopt a way which based on Mat lab, UART and FPGA platform.

With the increasing rate of wireless devices and high bandwidth operations, wireless networking and communications are becoming over crowded. To cope with such crowded and messy situation, massive MIMO is designed to work with hundreds of low-cost serving antennas at a time as well as improve the spectral efficiency at the same time. Time Division Duplexing (TDD) has been used for gaining beamforming which is a major part of massive MIMO, to gain its best improvement to transmit and receive pilot sequences. All the benefits are only possible if the channel state information or channel estimation is gained properly. Least Square (LS), Minimum Mean Square Error (MMSE) and Linear Minimum Mean Square Error (LMMSE) are the estimators commonly used for estimating channel matrices. We have optimized these methods using genetic algorithm to minimize the mean squared error and finding the best channel matrix from existing algorithms with less computational complexity. Our simulation result has shown that the use of Genetic Algorithm (GA) worked well on existing algorithms in a Rayleigh slow fading channel and existence of Additive White Gaussian Noise. We found that the GA optimized LS is better than existing algorithms. GA provides optimal result in some few iterations in terms of Mean Square Error (MSE) with respect to SNRand computational complexity.

Visible light communication (VLC) has been proposed as a promising way for next generation wireless communication networks to mitigate the scarcity of the radio frequency (RF) spectrum, and has consequently attracted much attention. This paper introduces a single-input single-output (SISO) VLC system under the joint effects of statistical random channel and signal-dependent shot noise (SDSN). Moreover, it estimates the channel of the considered system using maximum likelihood (ML), least square (LS), linear minimum mean square error (LMMSE), maximum posteriori probability (MAP) and minimum mean square error (MMSE) estimators. Furthermore, a Bayesian Cramér-Rao lower bound (BCRLB) is derived for the proposed system and it is compared to the mean square error (MSE) of the proposed estimators. The problem of unknown SDSN factor, <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$\zeta ^{2}$</tex-math></inline-formula> , at the receiver side is discussed and two solutions are investigated. The receiver of a VLC system under SDSN and random channel gain <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex-math notation="LaTeX">$h$</tex-math></inline-formula> is designed and its BER is studied. Finally, Monte Carlo simulation results of the proposed estimators, which show the dramatic effect of the SDSN on the considered system, are provided. In particular, the presence of noise variance, as well as the SDSN factor, causes an increase in the MSE of the system, while increasing the power reinforces the system performance.

This paper studies the effect of channel estimation in WiMAX system. The channel estimation is based on the principle of pilot-symbol-aided channel estimation (PACE) in frequency domain. The algorithms used here are based on the least squares (LS) and the minimum mean squares error (MMSE) approaches. Furthermore we propose a simple method to reduce the computation complexity of MMSE algorithm significantly which has a desirable performance. In the end, our result will quantitatively demonstrate the effect of LS, MMSE and proposed low complexity MMSE algorithms for uncoded IEEE802.16d standard of WiMAX system.

If N is standard Gaussian, the minimum mean square error (MMSE) of estimating a random variable X based on √( <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">snr</i> ) <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">X</i> + <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">N</i> vanishes at least as fast as 1/ <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">snr</i> as <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">snr</i> → ∞. We define the MMSE dimension of X as the limit as <i xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">snr</i> → ∞ of the product of snr and the MMSE. MMSE dimension is also shown to be the asymptotic ratio of nonlinear MMSE to linear MMSE. For discrete, absolutely continuous or mixed distribution we show that MMSE dimension equals Rényi's information dimension. However, for a class of self-similar singular X (e.g., Cantor dis tribution), we show that the product of snr and MMSE oscillates around information dimension periodically in snr (dB). We also show that these results extend considerably beyond Gaussian noise under various technical conditions.

In a companion paper, we have studied the zero-forcing (ZF) transceiver with decision feedback equalizer (DFE) over slowly time-varying narrowband multiinput multioutput (MIMO) channels. The space-time generalized triangular decomposition (ST-GTD) was used for the design of ZF-DFE transceivers. The space-time geometric mean decomposition (ST-GMD) ZF transceiver minimizes both the arithmetic mean square error (MSE) at the feedback detector and the average uncoded bit error rate (BER) in moderate high signal-to-noise ratio (SNR). This paper addresses the design problem of DFE transceiver without zero-forcing constraint. In the first part, a channel independent temporal precoder is superimposed on the conventional block-wise GMD-based minimum mean square error (MMSE) DFE transceiver to take advantage of the temporal diversity. In the second part, ST-GTD is applied for the design of MMSE DFE transceivers. With accurate channel prediction and space-time powerloading, the proposed ST-GMD MMSE transceiver minimizes the arithmetic MSE at the feedack detector, and maximizes Gaussian mutual information. For practical applications, the ST-GTD MMSE transceiver which does not require channel prediction but shares the same asymptotic BER performance with the ST-GMD MMSE system is also developed. In the convex region, our analysis shows that the proposed MMSE transceivers has better BER performance than the conventional GMD-based MMSE transceiver; the average BERs of the proposed systems are nonincreasing functions of the ST-block size. The superior performance of ST-GMD MMSE transceiver over the ST-GMD ZF transceiver is also verified analytically.