MPPT Algorithm Based on Improved PSO and Fuzzy Algorithm

In the case of partial shading conditions, there will be more than one maximum power point (MPP) in photovoltaic (PV) array. The traditional maximum power point tracking (MPPT) methods are easy to get in the local maximum power point (LMPP) and fail. Based on the standard differential evolution (DE) algorithm, the mutation strategy, scaling factor F, and cross factor CR of the algorithm are optimized. Also, the population position variance δ 2 is used to prevent falling into LMPP. Finally, the conditions for algorithm termination and restart are set. It is verified by simulation that the method has fast convergence speed, high accuracy, and can adapt well to changes in the external environment. The improved DE algorithm has a great advantage in MPPT.

The maximum power point tracking (MPPT) system ensures that the solar cell operates at its maximum power point, which is the point at which it produces the most power for a given set of conditions. This study uses an artificial bee colony (ABC) algorithm and particle swarm optimization (PSO) algorithms to optimize the boost converter. The ABC and PSO algorithms help to optimize the boost converter by finding the best possible duty cycle and other parameters that maximize efficiency. The resulting duty cycle of 20% produced the highest efficiency of 78.26% obtained from the boost converter. A system-wide test was conducted between 9:00 and 11:10 WIB. In MPPT systems using boost converters with the PSO algorithm, the average power is 16.80 W, while in MPPT systems using boost converters with the ABC algorithm, the average power is 14.53 W. The novelty of the study discusses a system designed to optimize power by using a boost converter in order to increase power output from solar panels. The algorithms PSO and ABC are used to analyze the data from the PV and adjust the converter parameters to optimize the output in order to increase the efficiency of the system.

In order to use photovoltaic cell effectively and improve its photoelectric conversion efficiency, the maximum power point of photovoltaic generation system should be tracked rapidly and stably. In this paper after comparison and analysis common methods used in controller of photovoltaic systems such as Fuzzy and P&O, proposed an approach combined from FLC and particle swarm optimization algorithm (PSO) as an appropriate method to achieve maximum power point tracking (MPPT). Indeed Fuzzy logic control can cope with photovoltaic system using heuristic knowledge rules, but tuning the control parameters is not straightforward. PSO performs an on-line haphazard global search for input and output scaling factors of a PD-type fuzzy controller. The objective function of the PSO algorithm has been defined to minimize slope of P-V curve. The simulation results in SIMULINK of MATLAB indicate that proposed method can effectively eliminate the power oscillation around MPP and raise stability and reach steady state of the system.

Since the performance of the Photo-Voltaic (PV) arrays is dependent on irradiation and temperature, the PV output power fluctuates with the ambient temperature and the solar irradiance. The achievement of the Maximum Power Point (MPP) under various shading patterns is, as a result, an important aspect in the enhancement of PV systems' overall performance. Because existing methodologies, such as perturb & observe, incremental conductance, etc., are likely to fail, it is necessary to develop an improved Maximum Power Point Tracking (MPPT) method to distinguish between the Global MPP (GMPP) and the Local MPP (LMPP). The characteristics of a PV array under shading conditions include several LMPPs and a single GMPP. To improve the MPPT method of shaded photovoltaic systems, this paper introduces an improved Particle Swarm Optimization (PSO) algorithm with Time-Varying Acceleration Coefficients (PSO-TVAC) that is fast and more efficient than the PSO. Firstly, the PSO-TVAC algorithm is mathematically modeled and applied to the MPPT application for solar PV systems. The primary objective of this paper is to analyze the performance of the PSO-TVAC for the MPPT application. Three shading patterns are considered to study the effectiveness of the PSO-TVAC in handling the MPPT application. The results and discussions prove that PSO-TV AC can be an alternative tool for MPPT application for PV systems.

Considering the slow convergence speed and unstable transmission capacity of photovoltaic systems in maximum power point tracking (MPPT), this paper proposes a MPPT control strategy based on the fine-layered population algorithm. This strategy improves the search efficiency of the algorithm by fine-layered sequence reconstruction of the sparrow search algorithm (SSA) and particle swarm optimization algorithm (PSO) populations. Firstly, a PSO population pause mechanism is introduced to avoid the premature convergence problem of PSO. Secondly, a fine-layered sequence is used to generate a uniformly distributed initial population, and the cooperative optimization of the sparrow group and the particle swarm is designed to improve the compatibility of the algorithm. The two main populations are decomposed, the number of individuals in the population is optimized, and the individual optimal fitness value of the population is updated. At the same time, the population position is reorganized in each layer to enable each layer to optimize independently, making the entire population easier to collaborate, increasing population diversity, and thereby improving search efficiency. Finally, strategies such as filling functions and sign matrices are introduced into the speed update position of the improved hierarchical population algorithm (PSSSA) to reduce the adverse effects of power fluctuations caused by boundary effects, improve the convergence and speed of the algorithm, and ensure that the optimal solution is obtained after each update. To verify the effectiveness of the PSSSA algorithm, a simulation model under the weather conditions of a certain laboratory in Northeast China was constructed using Matlab. The simulation results show that when it is applied to the maximum power tracking problem, in the case of rapid changes in external environmental illumination, it can accurately track the maximum power point within 0.2 seconds. Its tracking stability is significantly better than the Particle Swarm Optimization (PSO) algorithm, the Seagull Search Algorithm (SSA), and the Perturbation Observation (P&O) algorithm. The size of the maximum power point is approximately 64% larger than that of the PSO algorithm. At the same time, it can also ensure the stability and rapidity of the tracking effect.

The extraction of solar energy will be higher using the multijunction solar cells instead of single junction solar cell by splitting the solar spectrum. This work proposes a detailed study to identify the optimum interconnection method for various multijunction solar cells. An effective power electronic circuit could substantially enhance the efficiency and utilization of a photovoltaic (PV) power system constructed from multijunction solar cells. The multiple input dc-dc non-inverting buck-boost converter is used to demonstrate the advantage of the proposed interconnection technique, which can maintain a constant output voltage by performing both the buck and boost mode of operation. In order to ensure maximum power point (MPP) operation, a particle swarm optimization (PSO) algorithm is applied which needs only one MPP control for multiple solar modules resulting reduction in cost and complexity. The PSO algorithm has the ability to track the global maxima of the system even under complex illumination situations.

To get the most power out of photovoltaic (PV) panels, PV systems must utilize a maximum power point tracking (MPPT) controller. In partial shading conditions (PSC), the power-voltage (P-V) characteristic of the PV network may show a single global maximum power point (GMPP) and two or more local maximum power points (LMPP). This indicates that the PV cells and panels do not get uniform illumination. As they converge on the maximum power point (MPP) that makes contact first, which is often one of the LMPPs in this scenario, common MPPT approaches like incremental conductance (InC) and perturb and observe (P&O) are unable to distinguish between a GMPP and LMPPs. In this paper, the extraction of the GMPP of the PV system under PSC based on a suggested particle swarm optimization (PSO) approaches is presented. The particularity of the suggested approach is that it takes into account the calculation of the position of each particle as a function of the duty cycle and the global maximum power. Results on the performance of the suggested PSO method show an advantage over the conventional PSO and the commonly used traditional P&O method. The suggested PSO technique offer better performance in terms of global power extracted, ripple rate of the power and efficiency.

The partial shading of a photovoltaic array repeatedly occurs in the natural environment, which can cause a failure of a conventional maximum power point tracking (MPPT) algorithm. In this paper, the convergence conditions of the standard particle swarm optimization (PSO) algorithm are deduced by the functional analysis, and then the influence of the random variables and inertia factor of the algorithm on the trajectory in the particle swarm optimization is analyzed. Based on the analysis results, an improved particle swarm optimization (IPSO) algorithm, which adopts both global and local modes to locate the maximum power point, is proposed. Compared to the standard PSO algorithm, in the improved PSO algorithm, many random and interfered variables are removed, and the structure is optimized significantly. The proposed algorithm is first simulated in MATLAB to ensure its capability. The feasibility of the approach is validated through physical implementation and experimentation. Results demonstrate that the proposed algorithm has the capability to track the global maximum power point within 3.3 s with an accuracy of 99%. Compared with five recently developed Global MPPT algorithms, the proposed IPSO algorithm achieved better performance in the maximum power tracking in the partial shading conditions.

The particle swarm optimization (PSO) algorithm presents a new way for finding optimal solutions of complex optimization problems. In this paper a modified particle swarm optimization algorithm is presented. We modify the PSO algorithm in some aspects. Firstly, a contractive factor is introduced to the position update equation, and the particles are limited in search region. A new strategy for updating velocity is then adopted, in which the velocity is weakened linearly. Thirdly, using an idea of intersecting two modified PSO algorithms. Finally, adding an item of integral control in the modified algorithm can improve its global search ability. Based on these strategies, we proposed a new PSO algorithm named crossed PSO algorithm. Simulation results show that the crossed PSO is superior to the original PSO algorithm and can get overall promising performance over a wide range of problems.

Collaborative beamforming in wireless sensor networks using a novel particle swarm optimization algorithm variant

Neural Network system for SoC is one topic in the world. Recently, SoC began to combine AI technique by Python. When developers consider Intelligent system on SoC, the co-design software and hardware are significant. In this case, small devices and embedded system are target system. For IoT, those techniques will grow up in the world. Those cases, avoiding premature convergence while keeping performance is a challenge in training the neural network, especially in a case of large NNs or a large number of training data. In this case, one problem is a huge memory and processing power. For tiny memory and processing system as SoC, we propose an improved particle swarm optimization (PSO) algorithm called the PSOseed2 algorithm for training NN. The PSOseed2 algorithm solves the premature convergence of the standard PSO (SPSO) algorithm by slightly modifying the velocity update function without adding many computational tasks to the SPSO algorithm. We evaluated this algorithm on field programmable gate array (FPGA)-based NN and software-based NN and trained these NNs with different PSO algorithms that are SPSO, PSOseed, PSOseed2, and dissipative PSO. Experimental results with different datasets confirmed that the NNs trained by the proposed PSOseed2 algorithm had better recognition rates and lower global learning errors than the NN trained by other PSO algorithms. In this talk, I would like to talk those relational research in the world and our results and discussion.

Maximum power point tracking (MPPT) control is one of the essential requirements in harnessing wind power of wind energy conversion systems (WECS). The more precise the maximum power point (MPP) is determined, the more optimal the WECS is operated. Amongst MPPT algorithms, a hill-climb search (HCS) algorithm is preferred because of its simplicity however it also has few drawbacks such as the difficulty of selecting an appropriate step size, the premature convergence phenomenon and the speed-efficiency trade-off. A cuckoo search (CS) algorithm is proposed in this paper for finding out a MPP of a WECS driven by a doubly-fed induction generator (DFIG) under various wind speeds which mostly overcomes the above disadvantages. Then, the DFIG-WECS is controlled to track the MPP. This ensures that the DFIG-WECS is always operated at MPPs regardless of various wind speeds. It is realized that the proposed CS algorithm is also a population-based algorithm inspired from the breeding behavior of cuckoos but it is quite simple, powerful and especially requires less parameters to define optimal solutions than a genetic algorithm (GA) and a particle swarm optimization (PSO) algorithm. Though numerical results, the CS algorithm shows its effectiveness in finding out MPPs in the DFIG-WECS. Furthermore, the obtained results using the CS algorithm are also compared with those using the HCS and PSO algorithms. The comparison demonstrates that the convergence value and speed of the CS algorithm are always better than those of the HCS and PSO algorithms in the MPPT application in the DFIG-WECS.

Dynamic global maximum power point tracking of the PV systems under variant partial shading using hybrid GWO-FLC

Photovoltaic power generation systems will switch between two situations: uniform illumination and local shadow. For maximum power point tracking (MPPT), the conventional strategy is often efficient in only one situation. But for both situations with switching, there face problems such that the tracking time may be too long or it may fall into the local maximum power point (LMPP). Aiming at these problems, in this paper, an event-triggered dual-mode control technology is proposed, which enables the system to work with high efficiency and high precision under both uniform illumination and local shadow. Under the uniform illumination, the maximum power point is tracked by the perturbation method (P&O), while in a local shaded environment, the current flowing through the bypass diode acts as a trigger signal which enables Particle Swarm Optimization (PSO) to track the Global Maximum Power Point (GMPP). The simulation experiment by Matlab shows that in both the uniform illumination and local shadow, the algorithm of event-triggered dual-mode control is efficient in MPPT and has a fast and smooth transition between P&O and PSO, overcoming the problems of conventional strategy.

The position of MPP of a solar panel changes with changes in weather conditions such as radiation, temperature and partial Shadow. In such a situation, several local MPPs and one GMPP are created in the P-V curve, and the common methods of MPPT(P&O, IC,…) have converged due to the failure to recognise the local MPP. They cause a lot of losses to the photovoltaic system. Therefore, in this article, it has been tried to provide a new method of particle swarm optimisation with variable coefficients, which in combination with the perturb and observe method can reach the GMPP in the fastest possible time. In this proposed method, we first reach the convergence of the GMPP using the VCPSO method, and after converging to it, we go to the P&O method and use P&O until significant changes are made in the system, and if observed Variations To re-examine the GMPP, we return to the VCPSO algorithm. The results of the simulation of the efficiency of the proposed method show that this method was able to reach the GMPP in the shortest time, and the efficiency of the photovoltaic system increases and the effects of partial shading are reduced.