ON PREVENTIVE MAINTENANCE POLICY FOR WAVE DISSIPATING BLOCKS COVERING CAISSON BREAKWATER

Optimal preventive maintenance policy for leased equipment using failure rate reduction

Different type of maintenance problems have been investigated during the past decades. With the growth in complexity of modern systems, the cost of purchasing new systems becomes higher ever than before. Surprisingly, very little attention in the literature has been paid to the failure replacement in these preventive maintenance models. However, in practice most systems incur increasingly expensive down time costs when the systems suffer the unexpected failures. The major changes to the standard maintenance model in this research are the addition of a failure replacement cost for a failed system and the reliability limit for which system has to be replaced. The overall objective of this research is to propose an efficient algorithm to obtain the optimal maintenance policy. The optimal preventive maintenance policy is investigated with incorporating the costs of minimal repair, imperfect preventive maintenance, failure replacement and preventive replacement. The specific maintenance actions for a repairable system are when to perform an imperfect preventive maintenance or to replace the system while the system is in the operating condition. In another case, the specific maintenance actions for a repairable system are whether to replace the system, or to perform a minimal repair when the system fails. The number of imperfect preventive maintenance and the control limits of the optimal maintenance policy are calculated under the expected average cost rate criterion.

A special game against nature is examined in this paper, in which nature controls timings of repairable and non-repairable failures of a system of equipment, and preventive maintenance, repairs and preventive replacement policies are the countermeasures. We optimize the imperfect preventive maintenance policy for a multi-unit system with different initial virtual age units. We develop a binary integer programming problem, where the management decides on the optimal preventive maintenance policy to minimize the total expected maintenance cost not to exceed a given budget. The mathematical formulation is developed for a multi-unit system, considering different preventive maintenance levels for each unit. Numerical examples with sensitivity analysis are performed to illustrate the performance and efficiency of the proposed model. Also, the model is examined for a real case study from railway industry. The results determine the optimal preventive maintenance policy and provide managerial insights based on computational analysis.

Thompson1 considers a linear control model to ascertain the optimal preventive maintenance policy for production equipment and, simultaneously, its optimal sale date. He assumes age‐dependent deterministic continuous deterioration, production rate and linear efficiency of maintenance expenditures. In the present paper we first consider a linear maintenance model under a budget constraint. The impact of such a restriction is an earlier switch in the optimal bang‐bang policy. Then a non‐linear, non‐autonomous generalization of Thompson's model is analysed by the maximum principle. The optimal maintenance policy is shown to be downward sloping provided that in each time period the production rate is greater than the sum of interest and deterioration rate. The monotonicity of the optimal rate of preventive maintenance holds also under the additional possibility of random machine failure provided the production rate is greater than the sum of the rate of interest, the rate of deterioration and the rate of stochastic failure at each age. Moreover, it is shown that the higher the failure rate the smaller the optimal expenditures for preventive maintenance at any fixed age of the machine. In particular, the optimal maintenance rate at age t in a model without random failure is greater than those in any case including stochastic failure at the same age.

PurposeWhile steady-state analysis is useful, it does not consider the inherent transient characteristics of repairable systems' behavior, especially in systems that have relatively short life spans, or when their transient behavior is of special concern such as the motivating example used in this paper, military systems. Therefore, a maintenance policy that considers both transient and steady-state availability and aims to achieve the best trade-off between high steady-state availability and rapid stabilization is essential.Design/methodology/approachThis paper studies the transient behavior of system availability under the Kijima Type II virtual age model. While such systems achieve steady-state availability, and it has been proved that deploying preventive maintenance (PM) can significantly improve its steady-state availability, this improvement often comes at the price of longer and increased fluctuating transient behavior, which affects overall system performance. The authors present a methodology that identifies the optimal PM policy that achieves the best trade-off between high steady-state availability and rapid stabilization based on cost-availability analysis.FindingsWhen the proposed simulation-based optimization and cost analysis methodology is applied to the motivating example, it produces an optimal PM policy that achieves an availability–variability balance between transient and steady-state system behaviors. The optimal PM policy produces a notably lower availability coefficient of variation (by 11.5%), while at the same time suffering a negligible limiting availability loss of only 0.3%. The new optimal PM policy also provides cost savings of about 5% in total maintenance cost. The performed sensitivity analysis shows that the system's optimal maintenance cost is sensitive to the repair time, the shape parameter of the Weibull distribution and the downtime cost, but is robust with respect to changes in the remaining parameters.Originality/valueMost of the current maintenance models emphasize the steady-state behavior of availability and neglect its transient behavior. For some systems, using steady-state availability as the sole metric for performance is not adequate, especially in systems that have relatively short life spans or when their transient behavior affects the overall performance. However, little work has been done on the transient analysis of such systems. In this paper, the authors aim to fill this gap by emphasizing such systems and applications where transient behavior is of critical importance to efficiently optimize system performance. The authors use military systems as a motivating example.

Optimal rearrangement and preventive maintenance policies for heterogeneous balanced systems with three failure modes

본 논문에서는 수리가 가능한 시스템에 대하여 혼합보증이 종료된 이후의 교체모형과 예방보전모형을 고려하는데, 만약 보증기간이 종료된 이후에 시스템에 고장이 발생하면 최소수리를 수행한다. 최적의 교체정책과 최적의 예방보전정책을 결정하기 위한 기준으로는 기대비용과 기대비가동시간에 근거한 총밸류함수를 사용한다. 그리고 시스템의 고장시간이 와이블분포를 할 때 수치적 예를 통해서 제안된 최적의 교체정책 및 예방보전정책을 자세히 설명하고자 한다. This paper considers the replacement model and the preventive maintenance model following the expiration of combination warranty for a repairable system. If the system fails after the combination warranty is expired, then it is minimally repaired at each failure. The criterion used to determine the optimal replacement policy and the optimal preventive maintenance policy is the overall value function based on the expected cost rate per unit time and the expected downtime per unit time. The numerical examples are presented for illustrative purpose when the failure time follows a Weibull distribution.

International audience

There have been many publications dealing with preventive maintenance policies for stochastically deteriorating systems. However, most of them study systems having one device subject to failure. Much of the limited research dealing with multi-device production systems has been conducted through simulation experiments. In this paper, the preventive maintenance problem for serial production systems is formulated as a mathematical model. This formulation permits management to analyse the impact of a preventive maintenance policy on a serial production system without resorting to simulation. Numerical examples are used to provide managerial implications for maintaining a serial production system. The results show that the operating characteristics of the stations are interrelated; therefore, it is important to examine the joint effects of a maintenance policy on the various stations of the production system simultaneously rather than study each station separately.

Optimal preventive maintenance policies, for a machine subject to deterioration with age and intermittent breakdowns and repairs, are derived using optimal control theory. The optimal policies are shown to be of bang-bang nature. The extension to the case when there are a large number of identical machines and several repairmen in the system is considered next. This model takes into account the waiting line formed at the repair facility and establishes a link between this problem and the classical ``repairmen problem.''

The need for suitable replacement policies are essential to minimize down time, maintenance cost and maximize the availability and reliability of equipment. On this premise, this work models the failure rate of Photocopy machines and obtain its optimal preventive maintenance policy that would prevent damage and its attendant losses to both users and end-product consumers. The failure distribution of the machine was shown to follow the Log-Logistic distribution with shape parameter, ˆα=1.723339368 and scale parameter, ˆβ=763.9219635. Optimal probabilities of the distribution were obtained and utilized in both the cumulative failure function and cumulative hazard function-based replacement models to formulate a replacement maintenance policy for the machine. The failure cumulative function-based replacement model was found to be a better model which yields optimal replacement maintenance time of 166 hours at a minimum cost of 113 Naira for maintaining the machine per cycle time with 96% availability, 94% reliability and 0.07% chance of failure occurrence in the machine.

Reliability modeling and optimal random preventive maintenance policy for parallel systems with damage self-healing

Optimal preventive maintenance policy of the balanced system under the semi-Markov model

As an airframe has finite lifetime and has to be designed lightweight, the maintenance of airframe is indispensable to operate aircraft without any serious troubles. After an airframe begins to operate, it suffers stresses and the stress causes the damage such as cracks of the airframe. Cracks grow with operation time and cause catastrophic phenomenon such as the mid-air disintegration when they become greater than a critical size. So, the managerial crack size is prespecified and Preventive Maintenance (PM) undergoes when the inspected crack size exceeds it. In this paper, optimal PM policies of airframe crack failure are discussed. Airframe states are represented as the Markov renewal process, and one-step transition probabilities are discussed. The total expected cost from the start of operation to the end by failure is defined and the optimal PM policies which minimize it is discussed.

An Efficient Jaya Algorithm for Joint Optimization of Preventive Maintenance and Quality Policy in Production Systems