OPTIMAL MAINTENANCE OF AIRFRAME CRACKS

Optimal preventive maintenance policy for leased equipment using failure rate reduction

PurposeWhile steady-state analysis is useful, it does not consider the inherent transient characteristics of repairable systems' behavior, especially in systems that have relatively short life spans, or when their transient behavior is of special concern such as the motivating example used in this paper, military systems. Therefore, a maintenance policy that considers both transient and steady-state availability and aims to achieve the best trade-off between high steady-state availability and rapid stabilization is essential.Design/methodology/approachThis paper studies the transient behavior of system availability under the Kijima Type II virtual age model. While such systems achieve steady-state availability, and it has been proved that deploying preventive maintenance (PM) can significantly improve its steady-state availability, this improvement often comes at the price of longer and increased fluctuating transient behavior, which affects overall system performance. The authors present a methodology that identifies the optimal PM policy that achieves the best trade-off between high steady-state availability and rapid stabilization based on cost-availability analysis.FindingsWhen the proposed simulation-based optimization and cost analysis methodology is applied to the motivating example, it produces an optimal PM policy that achieves an availability–variability balance between transient and steady-state system behaviors. The optimal PM policy produces a notably lower availability coefficient of variation (by 11.5%), while at the same time suffering a negligible limiting availability loss of only 0.3%. The new optimal PM policy also provides cost savings of about 5% in total maintenance cost. The performed sensitivity analysis shows that the system's optimal maintenance cost is sensitive to the repair time, the shape parameter of the Weibull distribution and the downtime cost, but is robust with respect to changes in the remaining parameters.Originality/valueMost of the current maintenance models emphasize the steady-state behavior of availability and neglect its transient behavior. For some systems, using steady-state availability as the sole metric for performance is not adequate, especially in systems that have relatively short life spans or when their transient behavior affects the overall performance. However, little work has been done on the transient analysis of such systems. In this paper, the authors aim to fill this gap by emphasizing such systems and applications where transient behavior is of critical importance to efficiently optimize system performance. The authors use military systems as a motivating example.

A special game against nature is examined in this paper, in which nature controls timings of repairable and non-repairable failures of a system of equipment, and preventive maintenance, repairs and preventive replacement policies are the countermeasures. We optimize the imperfect preventive maintenance policy for a multi-unit system with different initial virtual age units. We develop a binary integer programming problem, where the management decides on the optimal preventive maintenance policy to minimize the total expected maintenance cost not to exceed a given budget. The mathematical formulation is developed for a multi-unit system, considering different preventive maintenance levels for each unit. Numerical examples with sensitivity analysis are performed to illustrate the performance and efficiency of the proposed model. Also, the model is examined for a real case study from railway industry. The results determine the optimal preventive maintenance policy and provide managerial insights based on computational analysis.

Hundreds of scholarly papers on optimisation of preventive maintenance policies for items under warranty have been published in the reliability related literature. They typically have two limitations: they make a simplified assumption on the relationship between age and usage for items under two-dimensional warranty and they assume that it is cost-effective to conduct preventive maintenance (PM) on each sold product item. These assumptions may not reflect the reality. This paper therefore proposes a copula-based approach to modelling the relationship between age and usage of items under two-dimensional (2D) warranty. It investigates the probabilistic properties of the bivariate failure rate functions of age and usage and derives optimal PM policies for users who bought multiple product items. It also proposes approaches to incorporating maintenance effectiveness in bivariate copulas for depicting the dependence between age and usage. A case study and numerical examples are provided to illustrate the findings.

Optimal rearrangement and preventive maintenance policies for heterogeneous balanced systems with three failure modes

Different type of maintenance problems have been investigated during the past decades. With the growth in complexity of modern systems, the cost of purchasing new systems becomes higher ever than before. Surprisingly, very little attention in the literature has been paid to the failure replacement in these preventive maintenance models. However, in practice most systems incur increasingly expensive down time costs when the systems suffer the unexpected failures. The major changes to the standard maintenance model in this research are the addition of a failure replacement cost for a failed system and the reliability limit for which system has to be replaced. The overall objective of this research is to propose an efficient algorithm to obtain the optimal maintenance policy. The optimal preventive maintenance policy is investigated with incorporating the costs of minimal repair, imperfect preventive maintenance, failure replacement and preventive replacement. The specific maintenance actions for a repairable system are when to perform an imperfect preventive maintenance or to replace the system while the system is in the operating condition. In another case, the specific maintenance actions for a repairable system are whether to replace the system, or to perform a minimal repair when the system fails. The number of imperfect preventive maintenance and the control limits of the optimal maintenance policy are calculated under the expected average cost rate criterion.

There have been many publications dealing with preventive maintenance policies for stochastically deteriorating systems. However, most of them study systems having one device subject to failure. Much of the limited research dealing with multi-device production systems has been conducted through simulation experiments. In this paper, the preventive maintenance problem for serial production systems is formulated as a mathematical model. This formulation permits management to analyse the impact of a preventive maintenance policy on a serial production system without resorting to simulation. Numerical examples are used to provide managerial implications for maintaining a serial production system. The results show that the operating characteristics of the stations are interrelated; therefore, it is important to examine the joint effects of a maintenance policy on the various stations of the production system simultaneously rather than study each station separately.

Reliability modeling and optimal random preventive maintenance policy for parallel systems with damage self-healing

Optimal preventive maintenance policy of the balanced system under the semi-Markov model

Purpose Making decisions on preventive maintenance (PM) policy and buffer sizing, as is often studied, may not result in overall optimization. The purpose of this paper is to propose a joint model that integrates PM and buffer sizing with consideration of quality loss for a degenerating system, which aims to minimize the average operation cost for a finite horizon. The opportunistic maintenance (OM) policy which could increase the output and decrease the cost of the system is also explored. Design/methodology/approach A joint PM and buffer size model considering quality loss is proposed. In this model, the time-based PM and the condition-based PM are taken on the upstream and the downstream machine, respectively. Further, the OM policy based on the theory of constraints (TOC) is also considered. An iterative search algorithm with Monte Carlo is developed to solve the non-linear model. A case study is conducted to illustrate the performance of the proposed PM policies. Findings The superiority of the proposed integrated policies compared with the separate PM policy is demonstrated. Effects of the policies are testified. The advantages of the proposed TOC-based OM policy is highlighted in terms of low-cost and high-output. Originality/value Few studies have been carried out to integrate decisions on PM and buffer size when taking the quality loss into consideration for degenerating systems. Most PM models treat machines equally ignoring the various roles of them. A more comprehensive and integrated model based on TOC is proposed, accompanied by an iterative search algorithm with Monte Carlo for solving it. An OM policy to further improve the performance of system is also presented.

International audience

ABSTRACTA framework for reliability and maintenance analysis of job shop manufacturing systems is proposed in this paper. An efficient preventive maintenance (PM) policy in terms of failure effects analysis (FEA) is proposed. Subsequently, reliability evaluation and component importance measure based on FEA are performed under the PM policy. A job shop manufacturing system is applied to validate the reliability evaluation and dynamic maintenance policy. Obtained results are compared with existed methods and the effectiveness is validated. Some vague understandings for issues such as network modelling, vulnerabilities identification, the evaluation criteria of repairable systems, as well as PM policy during manufacturing system reliability analysis are elaborated. This framework can help for reliability optimisation and rational maintenance resources allocation of job shop manufacturing systems.

본 논문에서는 수리가 가능한 시스템에 대하여 혼합보증이 종료된 이후의 교체모형과 예방보전모형을 고려하는데, 만약 보증기간이 종료된 이후에 시스템에 고장이 발생하면 최소수리를 수행한다. 최적의 교체정책과 최적의 예방보전정책을 결정하기 위한 기준으로는 기대비용과 기대비가동시간에 근거한 총밸류함수를 사용한다. 그리고 시스템의 고장시간이 와이블분포를 할 때 수치적 예를 통해서 제안된 최적의 교체정책 및 예방보전정책을 자세히 설명하고자 한다. This paper considers the replacement model and the preventive maintenance model following the expiration of combination warranty for a repairable system. If the system fails after the combination warranty is expired, then it is minimally repaired at each failure. The criterion used to determine the optimal replacement policy and the optimal preventive maintenance policy is the overall value function based on the expected cost rate per unit time and the expected downtime per unit time. The numerical examples are presented for illustrative purpose when the failure time follows a Weibull distribution.

In this paper, we consider a serial production line consisting of $$n$$n unreliable machines with $$n-1$$n-1 buffers. The objective is to determine the optimal preventive maintenance policy and the optimal buffer allocation that will minimize the total system cost subject to a given system throughput level. We assume that the mean time between failure of all machines will be increased after performing periodic preventive maintenance. An analytical decomposition-type approximation is used to estimate the production line throughput. The optimal design problem is formulated as a combinatorial optimization one where the decision variables are buffer levels and times between preventive maintenance. To solve this problem, the extended great deluge algorithm is proposed. Illustrative numerical examples are presented to illustrate the model.

The infrastructures are required to keep a certain level of performance during the duration of service. Because the performance of the infrastructures including harbor and coastal structures deteriorates due to aging and damage that is caused by the action of external forces, it is necessary to perform appropriate maintenance. Satow et al. (2009) proposed a mathematical model for the preventive maintenance of wave dissipating blocks based on the method of the reliability engineering. They also derived the expected maintenance cost over the in service period and the optimal preventive maintenance policy. In this study, the optimal threshold for preventive maintenance to minimize the expected maintenance cost is determined for the wave dissipating blocks covering caisson breakwater by using the above model.