Performance Analysis for MIMO SWIPT Systems with Space-Time Coding

This chapter examines simultaneous wireless information and power transfer (SWIPT) scenarios. It discusses the main SWIPT receivers, namely, separate and co-located receivers. The chapter provides numerical examples on the performance of the designed SWIPT precoding strategy. It focuses on a co-located SWIPT system, where a HAP serves a set S of devices performing both energy harvesting and information decoding in a given frequency band. The chapter illustrates some numerical results on the performance of the time switching and power splitting protocols. It also discusses some specific promising approaches to boost the performance of SWIPT systems for general wireless energy transfer (WET)-powered internet of things networks. WET and SWIPT systems are subject to non-linear responses that are often model-intractable unless too strong assumptions are adopted. The chapter concludes with an overview of some potential techniques to enable efficient SWIPT in future networks.

SummaryRadio frequency (RF) energy harvesting (EH) for wireless networks provides a green and sustainable solution and offers an energy‐efficient system. It is most crucial for fulfilling the power requirement of the rising number of low‐powered wireless devices and achieving sustainable development goals (SDG). It ensures the longevity of devices in the network even at inaccessible remote locations. Such RF‐EH‐based mechanisms are utilized in simultaneous wireless information and power transfer (SWIPT) systems. Most of the prevailing studies have analyzed the SWIPT system over conventional fading channels. However, due to the higher rate requirements, the current paradigm shift in frequency usage shifts towards the GHz band, which also offers better EH efficiency. Hence, SWIPT system analysis over the channel that is suitable for mm‐wave signal propagation is dealt with in this study. This study evaluates SWIPT performance over fluctuating two‐ray (FTR) fading channel that is crucial since it provides the best fit for characterizing GHz signal and also provides a generalized framework for most of the conventional fading channels. This study presents new analytical results assuming time switch relaying (TSR) protocol with (i) amplify and forward (AF) and (ii) decode and forward (DF) relaying. The results are also analyzed for H branches maximal ratio combining (MRC) diversity technique and evaluated the diversity gain for both AF and DF relays. The effectiveness of the system is measured in terms of system outage probability (SOP) to envisage the reliability of SWIPT based system. This work presents the simulation and modeling of such system and its obtained results are validated by Monte Carlo simulations for their accuracy.

This paper studies the outage performance of the hybrid amplify-and-forward (AF) relaying protocol in simultaneous wireless information and power transfer (SWIPT) systems with direct link. In the hybrid power-time switching based relaying (HPTSR), the block time T is divided into two parts. One is used for energy harvesting and information processing, and the other is used for information transmission from relay to destination node. During the part of energy harvesting and information processing, one portion of the received signal is used for energy harvesting (EH) and the other portion of the received signal is used for information processing. An analytical expressions for outage probability is derived in the hybrid AF-based relay network. Our numerical results verify our analytical expressions and shows that the proposed system performance of the hybrid protocol in the presence of the direct link outperforms the hybrid protocol without direct link.

In this paper, we investigate the simultaneous wireless information and power transfer (SWIPT) in a multiple-input multiple-output (MIMO) amplify-and-forward relay communication system, where the relay is an energy harvesting (EH) node and harvests the energy the signals transmitted from the source. The harvested energy is partially used to forward signals from the source to the destination, and the remaining energy is stored for other usages. The SWIPT in relay-assisted communication is interesting as long as the relay stores energy from the source and the destination receives successfully the data from the source. In this context, we propose to investigate the source and relay precoders that characterize the relationship between the achievable stored energy at the relay and the achievable source-to-destination rate, namely, the rate-stored energy (R-E) tradeoff region. First, we consider the ideal scheme, where there is the simultaneous operation of the EH and information decoding (ID) receivers at the relay. Then, we consider practical schemes, such as the power splitting and the time switching that separate the operation of EH and ID receivers over power domain or time domain, respectively. Moreover, we study the case of imperfect channel state information at the relay and the destination, and characterize its impact on the achievable R-E region. Through the simulation results, we show the effect of the position of the relay and the channel uncertainty on the achievable R-E regions of all the schemes when the used energy at the relay is constant or variable. We also show that, although it provides an outer bound on the achievable rate-energy region in one-hop MIMO systems, the ideal scheme provides only an upper bound on the maximum achievable end-to-end rate and not an outer bound on the R-E region.

The advent of 5G era and the increase of terminal’s numbers have led to increasing demand for spectrum resources and energy simultaneously. Therefore, this paper studies how to combine the cognitive radio (CR) and the Simultaneous Wireless Information and Power Transfer (SWIPT) technology effectively in a multiuser scenario, in which the spectrum utilization and energy efficiency are both improved. Firstly, the system model is designed of above cognitive SWIPT system, in which the cognitive users (CU) can choose spectrum access policy based on the amount of data transmission of licensed user. And then, according to cognitive users’ channel conditions and forwarding power, a concept of trust value and different relay selection policies is proposed. Subsequently, the according system ergodic capacity is analyzed. Finally, simulation results of system performance are provided to validate the analytical results. It shows that cognitive SWIPT technology can improve the system ergodic capacity and the spectrum access opportunities of cognitive users effectively, thereby improving the efficiency of energy and spectrum utilization.

The propagation loss of RF signals is a significant issue in simultaneous wireless information and power transfer (SWIPT) systems. Additionally, ensuring information security is crucial due to the broadcasting nature of wireless channels. To address these challenges, we exploit the potential of active intelligent reflecting surface (IRS) in a multiple-input and multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) SWIPT system. The active IRS provides better beamforming gain than the passive IRS, reducing the “double-fading” effect. Moreover, the noise introduced at the active IRS can be used as artificial noise (AN) to jam eavesdroppers. This paper formulates a secrecy sum-rate maximization problem related to precoding matrices, power splitting (PS) ratios, and the IRS matrix. Since the problem is highly non-convex, we propose a block coordinate descent (BCD)-based algorithm to find a sub-optimal solution. Moreover, we develop a heuristic algorithm based on the zero-forcing precoding scheme to reduce computational complexity. Simulation results show that the active IRS achieves a higher secrecy sum rate than the passive and non-IRS systems, especially when the transmit power is low or the direct link is blocked. Moreover, increasing the power budget at the active IRS can significantly improve the secrecy sum rate.

We develop an analytical framework to characterize the effect of impulsive noise on the performance of relay-assisted simultaneous wireless information and power transfer (SWIPT) systems. We derive novel closed-form expressions for the pairwise error probability considering two variants based on the availability of channel state information (CSI), namely, blind relaying and CSI-assisted relaying. We further consider two energy harvesting (EH) techniques, i.e., instantaneous EH (IEH) and average EH (AEH). Capitalizing on the derived analytical results, we present a detailed numerical investigation of the diversity order for the underlying scenarios under the impulsive noise assumption. For the case when two relays and the availability of a direct link, it is demonstrated that the considered SWIPT system with blind AEH-relaying is able to achieve an asymptotic diversity order of less than 3, which is equal to the diversity order achieved by CSI-assisted IEH-relaying. This result suggests that, by employing the blind AEH relaying, the power consumption of the network can be reduced, due to eliminating the need of CSI estimation. This can be achieved without any performance loss. Our results further show that placing the relays close to the source can significantly mitigate the detrimental effects of impulsive noise. Extensive Monte Carlo simulation results are presented to validate the accuracy of the proposed analytical framework.

In this paper, we investigate a new approach for simultaneous wireless information and power transfer (SWIPT) in point-to-point multiple-input multiple-output (MIMO) system with spatial switching (SS) reception. The new approach is based on the generalized triangular decomposition (GTD). The approach takes advantage of the GTD structure to allow the transmitter to use the strongest subchannel jointly for energy harvesting and information exchange while these transmissions can be separated at the receiver to comply with the SS system requirements. An optimal solution is developed in the paper for SWIPT based on GTD that jointly obtains the optimal subchannels assignment and maximizes the total data rate while meeting the minimum requirement of the harvested energy with limited total transmitted power. The theoretical and numerical results presented in this paper show that the proposed approach significantly outperforms the state of the art spatial domain SWIPT systems based on the singular value decomposition (SVD).

Recently, simultaneous wireless information and power transfer (SWIPT) has emerged as a potential solution for improving energy efficiency. However, it is also unavoidable to be eavesdropped on by security threats. In this paper, we investigate the secure transmission of the SWIPT system where a user is equipped with power-splitting (PS) scheme while an eavesdropper (Eve) tries to listen to the private information of the transmitter-user communication link. Our objective is to optimize the system secrecy rate while satisfying the requirements on energy harvesting (EH) at the user and transmit power at the transmitter. For solving the optimization problem, we utilize the feasible point pursuit (FPP) technique and the successive convex approximation (SCA) iterative-based algorithm. Although this algorithm can effectively solve our non-convex problem, it is often quite complex and time-consuming due to the many mathematical transformations and the need for the number of iterations to be converged to the optimal solutions. Therefore, we also consider the deep learning (DL)-based approach which helps the optimization problem to achieve an efficient solution in terms of the computation time. The simulation results validate the proposed scheme significantly improve the system secrecy rate. Moreover, the DL scheme achieved similar performance to the optimization algorithm, but with low computation time.

In this paper, we investigate the performance of cache-assisted simultaneous wireless information and power transfer (SWIPT) cooperative systems, in which one source communicates with one destination via the aid of multiple relays. In order to prolong the relays’ serving time, the relays are assumed to be equipped with a cache memory and energy harvesting (EH) capability. Based on the time-splitting mechanism, we analyze the effect of caching on the system performance in terms of the serving throughput and the stored energy at the relay. In particular, two optimization problems are formulated to maximize the relay-destination throughput and the energy stored at the relay subject to some quality-of-service (QoS) constraints, respectively. By using the KKT conditions and with the help of the Lambert function, closed-form solutions are obtained for the two formulated problems. In order to further improve the performance, a relay selection policy is introduced to select the best relay based on either the maximum throughput between the relays’ and destination link or maximum stored energy at the relay, for conveying information to the destination. Numerical results reveal significant benefits of incorporating caching capabilities to SWIPT systems, in terms of improved serving time, throughput, and EH performance at the relays.

In this paper, the problem of joint mode switching and power adaptation is studied for simultaneous wireless information and power transfer (SWIPT) over a fading channel. The receiver dynamically switches between information decoding (ID) and energy harvesting (EH) modes while the transmitter dynamically adapts the transmit power. Considering the nonlinearity of practical EH circuits, a realistic nonlinear EH model is adopted rather than the idealistic linear EH model. To characterize the ultimate performance tradeoff between ID and EH, an optimization problem is formulated to maximize the average harvested energy under the constraints on the average achievable rate and the average transmit power, which is a nonconvex and combinatorial problem. To solve this problem, first, the optimal power adaptation scheme for the nonlinear EH receiver that operates only in the EH mode is proposed. Using this scheme, the jointly optimal solution for the mode switching and power adaptation is then derived. By comparing the obtained results to the existing results, various useful and interesting insights into the optimized SWIPT system with nonlinear EH are presented. An important insight into the impact of nonlinear EH is that, to exploit the high energy conversion efficiency of the nonlinear circuit, the EH mode has to be selected only in the moderate range of channel gains. Also, in the EH mode, the power has to be adapted to the short-term power threshold only for the moderate channel gains.

Simultaneous wireless information and power transfer (SWIPT) has emerged as a viable technique to energize and connect low-power autonomous devices and enable future Internet of Things (IoT). A major challenge of SWIPT is the energy consumption of the receiver of such low-power devices. An attractive low-power solution consists of an integrated information decoder (ID) and energy harvester (EH) architecture for SWIPT receiver (IntRx) where the received radiofrequency (RF) signal is first rectified before being used for information decoding. Such architecture eliminates the need for energy-consuming RF components, such as local oscillators and mixers. This article proposes a novel modulation and demodulation method for the IntRx SWIPT architecture based on pulse position modulation (PPM) where information is encoded in the position of the pulse. The new method transmits high amplitude pulses to increase the peak-to-average power ratio (PAPR) of the transmit signal and exploits the EH's nonlinearity so as to boost the harvested dc power. Simultaneously, the information can be decoded from the rectifier signal by simply finding the position of the pulse in a certain symbol duration. We have analyzed both the information and the power transfer performance of the newly proposed PPM for IntRx SWIPT theoretically, numerically, and experimentally. To that end, we have established a SWIPT system testbed in an indoor environment by prototyping a base station to transfer information-power signal and the IntRx SWIPT receiver, including ID and EH blocks. The performance evaluation of the PPM was carried out in various conditions, and the results have been compared and contrasted to conventional signals. Theoretical, numerical, and experimental results highlight the significant benefits of the proposed PPM scheme to enhance the power transfer performance and operate information decoding with low-power consumption.

This paper investigates the physical layer security issue in an amplify-and-forward (AF) multi-input multi-output (MIMO) two-way relay assisted cognitive radio (CR) nonorthogonal multiple access (NOMA) network, where the simultaneous wireless information and power transfer (SWIPT) technology is employed to improve network energy efficiency. We consider the scenario that a pair of primary users and two pairs of secondary users (SUs) exchange information via a MIMO two-way relay, where the edge SU of each SU pair is untrusted and tries to wiretap the central SU’s information. For ensuring security, we aim to maximize the sum achievable secrecy rate (SASR) by jointly optimizing the power allocation at all users, power splitting factor and relay beamforming subject to the quality of service (QoS), energy harvesting and transmit power constraints. The formulated optimization problem is highly nonconvex due to coupling variables, thus it is challenging to solve. An effective path-following (PF)-based algorithm is proposed, which is proven to converge to a stationary point. Theoretical and simulation results show that the proposed PF-based algorithm has lower complexity than the state-of-art algorithm. To further reduce complexity, we proposed a zero-forcing (ZF)-based scheme. Numerical simulations show that the proposed PF-based algorithm achieves the same SASR as the state-of-art algorithm with moderate complexity, while the proposed ZF-based scheme strikes a good balance between performance and complexity.

This paper presents a ASK modulation based modeling of Simultaneous Wireless Information and Power Transfer (SWIPT) system in LabVIEW. It supports in designing of SWIPT based system which able to harvest RF energy along with transfer of information simultaneously. At the receiver end, both RF energy harvesting (EH) and information decoding (ID) paths are modeled. RF energy harvesting path consists of RF rectifier and low pass filter. While ID path contains RF envelope detector and ASK demodulator. For the simulation verification of SWIPT system, a 2-ASK modulated RF signal is used at 900MHz. This modeling provides flexible parameters selection for the simulation of SWIPT system which helps in understanding and development of SWIPT system.

Intelligent Reflecting Surfaces (IRS) is a groundbreaking innovative technique to boost energy and spectral efficiency in upcoming wireless systems, enabling simultaneous wireless information and power transfer (SWIPT). This paper optimizes Energy Harvesting Efficiency (EHE) in a multi-input multi-output (MIMO) SWIPT system, where an access point (AP)/base station (BS) uses an IRS to serve multi energy receivers (ERs) and information receivers (IRs). We formulate an EHE optimization problem, designing active and passive beamforming while satisfying the AP/BS power constraints, IRS unit-modulus constraints and IR rate demands in a linear EH model. The Linear Matrix Inequalities (LMIs) are approximated for efficient solutions. And second-order cone programming (SOCP) is solved via convex optimization (CVX), while the penalty convex-concave procedure (CCP) guarantees convexity to non-convex problems. Next, an alternating optimization (AO)-reliant iterative algorithm derived sub-optimal solutions with slack variables. According to simulation results, for all ERs within a linear EH design/model, the proposed algorithm improves total EHE by 40% to 45% compared to randomize, No-IRS, and decode-and-forward (DF) relay strategies. Ultimately, highlighting IRS’s benefit in improving quality of service (QoS) by tweaking its elements and AP/BS antennas.