Simultaneous Wireless Information and Power Transfer

SummaryRadio frequency (RF) energy harvesting (EH) for wireless networks provides a green and sustainable solution and offers an energy‐efficient system. It is most crucial for fulfilling the power requirement of the rising number of low‐powered wireless devices and achieving sustainable development goals (SDG). It ensures the longevity of devices in the network even at inaccessible remote locations. Such RF‐EH‐based mechanisms are utilized in simultaneous wireless information and power transfer (SWIPT) systems. Most of the prevailing studies have analyzed the SWIPT system over conventional fading channels. However, due to the higher rate requirements, the current paradigm shift in frequency usage shifts towards the GHz band, which also offers better EH efficiency. Hence, SWIPT system analysis over the channel that is suitable for mm‐wave signal propagation is dealt with in this study. This study evaluates SWIPT performance over fluctuating two‐ray (FTR) fading channel that is crucial since it provides the best fit for characterizing GHz signal and also provides a generalized framework for most of the conventional fading channels. This study presents new analytical results assuming time switch relaying (TSR) protocol with (i) amplify and forward (AF) and (ii) decode and forward (DF) relaying. The results are also analyzed for H branches maximal ratio combining (MRC) diversity technique and evaluated the diversity gain for both AF and DF relays. The effectiveness of the system is measured in terms of system outage probability (SOP) to envisage the reliability of SWIPT based system. This work presents the simulation and modeling of such system and its obtained results are validated by Monte Carlo simulations for their accuracy.

Energy supply is a key factor affecting the normal operation of energy-constrained networks. Simultaneous wireless information and power transfer (SWIPT) technology can be used to obtain a stable and continuous energy source. But SWIPT need to take into account data transmission rate and energy harvesting performance, it is necessary to design a complex physical layer method to improve the energy efficiency of SWIPT system. The paper studies a multiple input multiple output (MIMO) SWIPT system based on space-time coding, the transmitter sends the information using the space-time encoder through multi-antenna transmission, the receiver uses the space-time decoder to decode the information and collect the energy. The expressions of channel capacity and energy harvesting under MIMO are given respectively. The energy harvesting optimization target equation under coding conditions is established. The simulation results show that the using of space-time coding can reduce the data transmission error rate of MIMO SWIPT system and improve the energy harvesting performance of the user terminals.

This paper presents a ASK modulation based modeling of Simultaneous Wireless Information and Power Transfer (SWIPT) system in LabVIEW. It supports in designing of SWIPT based system which able to harvest RF energy along with transfer of information simultaneously. At the receiver end, both RF energy harvesting (EH) and information decoding (ID) paths are modeled. RF energy harvesting path consists of RF rectifier and low pass filter. While ID path contains RF envelope detector and ASK demodulator. For the simulation verification of SWIPT system, a 2-ASK modulated RF signal is used at 900MHz. This modeling provides flexible parameters selection for the simulation of SWIPT system which helps in understanding and development of SWIPT system.

Simultaneous wireless information and power transfer (SWIPT) has emerged as a viable technique to energize and connect low-power autonomous devices and enable future Internet of Things (IoT). A major challenge of SWIPT is the energy consumption of the receiver of such low-power devices. An attractive low-power solution consists of an integrated information decoder (ID) and energy harvester (EH) architecture for SWIPT receiver (IntRx) where the received radiofrequency (RF) signal is first rectified before being used for information decoding. Such architecture eliminates the need for energy-consuming RF components, such as local oscillators and mixers. This article proposes a novel modulation and demodulation method for the IntRx SWIPT architecture based on pulse position modulation (PPM) where information is encoded in the position of the pulse. The new method transmits high amplitude pulses to increase the peak-to-average power ratio (PAPR) of the transmit signal and exploits the EH's nonlinearity so as to boost the harvested dc power. Simultaneously, the information can be decoded from the rectifier signal by simply finding the position of the pulse in a certain symbol duration. We have analyzed both the information and the power transfer performance of the newly proposed PPM for IntRx SWIPT theoretically, numerically, and experimentally. To that end, we have established a SWIPT system testbed in an indoor environment by prototyping a base station to transfer information-power signal and the IntRx SWIPT receiver, including ID and EH blocks. The performance evaluation of the PPM was carried out in various conditions, and the results have been compared and contrasted to conventional signals. Theoretical, numerical, and experimental results highlight the significant benefits of the proposed PPM scheme to enhance the power transfer performance and operate information decoding with low-power consumption.

In this paper, the problem of joint mode switching and power adaptation is studied for simultaneous wireless information and power transfer (SWIPT) over a fading channel. The receiver dynamically switches between information decoding (ID) and energy harvesting (EH) modes while the transmitter dynamically adapts the transmit power. Considering the nonlinearity of practical EH circuits, a realistic nonlinear EH model is adopted rather than the idealistic linear EH model. To characterize the ultimate performance tradeoff between ID and EH, an optimization problem is formulated to maximize the average harvested energy under the constraints on the average achievable rate and the average transmit power, which is a nonconvex and combinatorial problem. To solve this problem, first, the optimal power adaptation scheme for the nonlinear EH receiver that operates only in the EH mode is proposed. Using this scheme, the jointly optimal solution for the mode switching and power adaptation is then derived. By comparing the obtained results to the existing results, various useful and interesting insights into the optimized SWIPT system with nonlinear EH are presented. An important insight into the impact of nonlinear EH is that, to exploit the high energy conversion efficiency of the nonlinear circuit, the EH mode has to be selected only in the moderate range of channel gains. Also, in the EH mode, the power has to be adapted to the short-term power threshold only for the moderate channel gains.

We develop an analytical framework to characterize the effect of impulsive noise on the performance of relay-assisted simultaneous wireless information and power transfer (SWIPT) systems. We derive novel closed-form expressions for the pairwise error probability considering two variants based on the availability of channel state information (CSI), namely, blind relaying and CSI-assisted relaying. We further consider two energy harvesting (EH) techniques, i.e., instantaneous EH (IEH) and average EH (AEH). Capitalizing on the derived analytical results, we present a detailed numerical investigation of the diversity order for the underlying scenarios under the impulsive noise assumption. For the case when two relays and the availability of a direct link, it is demonstrated that the considered SWIPT system with blind AEH-relaying is able to achieve an asymptotic diversity order of less than 3, which is equal to the diversity order achieved by CSI-assisted IEH-relaying. This result suggests that, by employing the blind AEH relaying, the power consumption of the network can be reduced, due to eliminating the need of CSI estimation. This can be achieved without any performance loss. Our results further show that placing the relays close to the source can significantly mitigate the detrimental effects of impulsive noise. Extensive Monte Carlo simulation results are presented to validate the accuracy of the proposed analytical framework.

This paper considers simultaneous wireless information and power transfer (SWIPT) mechanisms in a relaying network with finite blocklength (FBL) codes. The reliability of the network is optimized under both a power splitting (PS) protocol and a proposed joint PS and time switching (TS) protocol. Under both protocols, we first determine the overall error probability formulation of the SWIPT-enabled two-hop transmission in the FBL regime. Subsequently, we state and solve optimization problems minimizing the overall error probability. Via numerical analysis, we show the appropriateness of our analytical model and demonstrate the performance advantage of the proposed protocol in comparison to TS and PS protocols. In addition, we provide interesting insights on the system behavior by characterizing the impact of the blocklength, transmit power and packet size on the reliability performance.

This paper studies the outage performance of the hybrid amplify-and-forward (AF) relaying protocol in simultaneous wireless information and power transfer (SWIPT) systems with direct link. In the hybrid power-time switching based relaying (HPTSR), the block time T is divided into two parts. One is used for energy harvesting and information processing, and the other is used for information transmission from relay to destination node. During the part of energy harvesting and information processing, one portion of the received signal is used for energy harvesting (EH) and the other portion of the received signal is used for information processing. An analytical expressions for outage probability is derived in the hybrid AF-based relay network. Our numerical results verify our analytical expressions and shows that the proposed system performance of the hybrid protocol in the presence of the direct link outperforms the hybrid protocol without direct link.

We built a phased array system for high-power simultaneous wireless information and power transfer (SWIPT) using four 5.8-GHz injection-locked magnetrons. In the magnetron injection-locked state, the transmission efficiency was measured at different modulation rates. The fluctuation in the transmission efficiency was not more than 0.5%. We observed that dynamic beamforming does not affect communication quality. Using the magnetron phased array system, SWIPT experiments revealed that a frequency modulated (FM) signal that carries a video camera signal is transmitted and decoded during dynamic beamforming. In this SWIPT system, the main lobe transfers power, and information can be demodulated in front of the magnetron phased array from −90° to 90°. The maximum transmitted microwave power of the proposed system is 1637 W.

Programmable metasurfaces present significant capabilities in manipulating electromagnetic waves, making them a promising candidate for simultaneous wireless information and power transfer (SWIPT), which has the potential to enable sustainable wireless communication in complex electromagnetic environments. However, challenges remain in terms of maximum power transmission distance and stable phase manipulation with high-power scattered waves. Additionally, waveform limitations restrict average scattered power and rectifier conversion efficiency, affecting data transmission rates and energy transmission distance. Here we show an amplifying programmable metasurface (APM) and a joint modulation method to address these challenges. The APM mitigates the peak-to-average power ratio and improves maximum power, phase response stability, average output power, and rectifier conversion efficiency. Through experimental validation, we demonstrate the feasibility of the SWIPT system, showcasing simultaneous LED array powering and movie video transmission. This innovative SWIPT system holds promise for diverse applications, including 6 G wireless communications, IoT, implanted devices, and cognitive radio networks.

Simultaneous wireless information and power transfer (SWIPT) formed by the mixture of communication technology and power transmission is one of the research focuses in the field of wireless communication. This paper introduces the architecture of the SWIPT system, analyzes the key technologies, presents a 2.45GHz microwave rectifier circuit at low input power for energy harvesting. Finally, with the use of Ultra-Narrow Band (UNB) as the modulation scheme, the practical SWIPT receiver system is modeled and simulated. The results provide that using UNB signal as the modulation scheme is a new feasible way for SWIPT.

Chapter 10 - Transmit beamforming for simultaneous wireless information and power transfer

Intelligent Reflecting Surfaces (IRS) is a groundbreaking innovative technique to boost energy and spectral efficiency in upcoming wireless systems, enabling simultaneous wireless information and power transfer (SWIPT). This paper optimizes Energy Harvesting Efficiency (EHE) in a multi-input multi-output (MIMO) SWIPT system, where an access point (AP)/base station (BS) uses an IRS to serve multi energy receivers (ERs) and information receivers (IRs). We formulate an EHE optimization problem, designing active and passive beamforming while satisfying the AP/BS power constraints, IRS unit-modulus constraints and IR rate demands in a linear EH model. The Linear Matrix Inequalities (LMIs) are approximated for efficient solutions. And second-order cone programming (SOCP) is solved via convex optimization (CVX), while the penalty convex-concave procedure (CCP) guarantees convexity to non-convex problems. Next, an alternating optimization (AO)-reliant iterative algorithm derived sub-optimal solutions with slack variables. According to simulation results, for all ERs within a linear EH design/model, the proposed algorithm improves total EHE by 40% to 45% compared to randomize, No-IRS, and decode-and-forward (DF) relay strategies. Ultimately, highlighting IRS’s benefit in improving quality of service (QoS) by tweaking its elements and AP/BS antennas.

Recently, simultaneous wireless information and power transfer (SWIPT) has emerged as a potential solution for improving energy efficiency. However, it is also unavoidable to be eavesdropped on by security threats. In this paper, we investigate the secure transmission of the SWIPT system where a user is equipped with power-splitting (PS) scheme while an eavesdropper (Eve) tries to listen to the private information of the transmitter-user communication link. Our objective is to optimize the system secrecy rate while satisfying the requirements on energy harvesting (EH) at the user and transmit power at the transmitter. For solving the optimization problem, we utilize the feasible point pursuit (FPP) technique and the successive convex approximation (SCA) iterative-based algorithm. Although this algorithm can effectively solve our non-convex problem, it is often quite complex and time-consuming due to the many mathematical transformations and the need for the number of iterations to be converged to the optimal solutions. Therefore, we also consider the deep learning (DL)-based approach which helps the optimization problem to achieve an efficient solution in terms of the computation time. The simulation results validate the proposed scheme significantly improve the system secrecy rate. Moreover, the DL scheme achieved similar performance to the optimization algorithm, but with low computation time.

In this paper, we provide a comprehensive literature survey on simultaneous wireless information and power transfer (SWIPT) in multi-antenna systems. We first review recent contributions on the theory analysis of SWIPT from information theoretic standpoint and introduce the tradeoff between information transfer and power transfer under various settings. Then, we focus on the utilization of multi-antenna techniques to solve existing problems of SWIPT. Contributions on the implementation aspects of multi-antenna SWIPT are summarized. The performance of SWIPT is evaluated by different metrics, therefore, we review the works on dynamic SWIPT optimization based on objective function using multi-antenna techniques. In addition, the implementation of SWIPT brings up secure issue. Thus, we summarize recent works on secure SWIPT. Finally, we present researches combining SWIPT with state-of-the-art techniques due to potential application in different scenarios.