Prediction of Hydrogen Production from Solid Oxide Electrolytic Cells Based on ANN and SVM Machine Learning Methods

Near infrared spectroscopy was used in discrimination of intact bovine teeth in terms of animal sex, diet, tooth type and place of origin. Discriminant Analysis (DA) models were developed and tested using a stratified random 70:30 data split to calibration and test sets. Of the discriminant techniques of Soft Independent Modelling of Class Analogy (SIMCA), Partial Least Squares – DA, Artificial Neural Networks (ANN) and Support Vector Machine (SVM), SVM and PLS-DA models performed best in most instances, with pretreatment choice impacting technique success. For test set prediction of animal sex, an accuracy of 95% was achieved using a PLS-DA model, and similar performance achieved using a SVM model. SVM, ANN and SIMCA models predicted three categories of tooth type (deciduous, permanent unerupted and erupted) with similar accuracies (89, 79 and 82%, respectively), however, permanent unerupted teeth were conflated with permanent erupted teeth. Prediction accuracy for ANN, SVM and PLS-DA models were also similar for discrimination of teeth from animals on a grain versus grass diet (PLS-DA 82%). There was considerable variation between models in prediction of geographic origin. Of the seven locations, two were discriminated with true positive rate around 70% using SVM and ANN models. Potential applications of this technology are discussed.

Bio-oil production from rice husk, an abundant agricultural residue, has gained significant attention as a sustainable and renewable energy source. The current research aims to employ artificial neural network (ANN) and support vector machine (SVM) modeling techniques for the optimization of operating parameters for bio-oil extracted from rice husk ash (RHA) through pyrolysis. ANN and SVM methods are employed to model and optimize the operational conditions, including temperature, heating rate, and feedstock particle size, to enhance the yield and quality of bio-oil. Additionally, ANN modeling is utilized to create a predictive model for bio-oil properties, allowing for the efficient optimization of pyrolysis conditions. This research provides valuable insights into the production and properties of bio-oil from RHA. By harnessing the capabilities of ANN and SVM, this research not only aids in understanding the intricate relationships between process variables and bio-oil properties but also provides a means to systematically enhance the production process. The predictive results obtained from the ANN were found to be good when compared with the SVM. Several models with different numbers of neurons have been trained with different transfer functions. R values for the training, validation, and test phases are around 1.0, i.e., 0.9981, 0.9976, and 0.9978, respectively. The overall R-value was 0.9960 for the proposed network. The findings were considered acceptable, as the overall R-value was close to 1.0. The optimized operational parameters contribute to the efficient conversion of RHA into bio-oil, thereby promoting the use of this sustainable resource for renewable energy production. This approach aligns with the growing emphasis on reducing the environmental impact of traditional fossil fuels and advancing the utilization of alternative and environmentally friendly energy sources.

Aggregate stability is a useful soil physical dynamic index of soil resistivity to surface wind and water erosion in all ecosystems, especially, in arid and semi-arid regions. Two machine learning techniques including support vector machines (SVMs) and artificial neural networks (ANNs) were used to develop predictive models for the estimation of geometric mean diameter (GMD) of soil aggregates. An empirical multiple linear regression (MLR) model was also constructed as the benchmark to compare their performances. Furthermore, the influence of feature space dimension reduction using parallel genetic algorithm (PGA) on the prediction accuracy of all investigated techniques was evaluated. The ANN model achieved greater accuracy in GMD prediction as compared to the MLR and SVM models. The obtained ERROR% value in GMD prediction using the ANN model was 6.9%, while it was 15.7 and 10.6% for the MLR and SVM models, respectively. Feature selection using PGA improved the prediction accuracy of all investigated techniques. The coefficient of determination (R2) values between the measured and the predicted GMD values using PGA-based MLR, SVM, and ANN models increased by 20.0, 12.2, and 8.8% in comparison with the proposed MLR, SVM, and ANN models. In conclusion, it appears that the PGA-based ANN model could be considered as an alternative to conventional regression models for the GMD prediction.

Chatter remains a critical limitation in milling operations, impairing surface integrity, reducing tool life, and limiting productivity. Accurate real-time prediction of chatter is essential for achieving process stability and enhancing machining efficiency. This paper provides a comparative evaluation of Support Vector Machines (SVM) and Artificial Neural Networks (ANN) combined with Variational Mode Decomposition (VMD) for the accurate identification of chatter in real-time vibration data. The milling vibration signals are decomposed into an Intrinsic Mode Functions (IMFs) with VMD to obtain chatter sensitive features. Axial depth of cut, table feed and Spindle speed data combined with these characteristics are used as input to both ANN and SVM models. The ANN model uses Tangent Sigmoid (TANSIG) activation function and six training algorithms, out of which Levenberg-Marquardt (LM) is found to produce the best results. Experimental verification proved that the prediction accuracy of 91.44% was outstripped (over 87.21%) in terms of the SVM model by the ANN model. The robustness of this framework in detecting stable, transitional, and unstable cutting zones has also been demonstrated through Stability Lobe Diagrams (SLDs) analysis. The proposed VMD-ANN approach offers an accurate and efficient solution to chatter prediction and parameter optimisation in real-time, which further contributes to higher material removal rates, better surface quality, and a longer tool life for smart manufacturing applications.

Stuck pipe incidents are one of the contributors to non-productive time (NPT), where they can result in a higher well cost. This research investigates the feasibility of applying machine learning to predict events of stuck pipes during drilling operations in petroleum fields. The predictive model aims to predict the occurrence of stuck pipes so that relevant drilling operation personnel are warned to enact a mitigation plan to prevent stuck pipes. Two machine learning methodologies were studied in this research, namely, the artificial neural network (ANN) and support vector machine (SVM). A total of 268 data sets were successfully collected through data extraction for the well drilling operation. The data also consist of the parameters with which the stuck pipes occurred during the drilling operations. These drilling parameters include information such as the properties of the drilling fluid, bottom-hole assembly (BHA) specification, state of the bore-hole and operating conditions. The R programming software was used to construct both the ANN and SVM machine learning models. The prediction performance of the machine learning models was evaluated in terms of accuracy, sensitivity and specificity. Sensitivity analysis was conducted on these two machine learning models. For the ANN, two activation functions—namely, the logistic activation function and hyperbolic tangent activation function—were tested. Additionally, all the possible combinations of network structures, from [19, 1, 1, 1, 1] to [19, 10, 10, 10, 1], were tested for each activation function. For the SVM, three kernel functions—namely, linear, Radial Basis Function (RBF) and polynomial—were tested. Apart from that, SVM hyper-parameters such as the regularization factor (C), sigma (σ) and degree (D) were used in sensitivity analysis as well. The results from the sensitivity analysis demonstrate that the best ANN model managed to achieve an 88.89% accuracy, 91.89% sensitivity and 86.36% specificity, whereas the best SVM model managed to achieve an 83.95% accuracy, 86.49% sensitivity and 81.82% specificity. Upon comparison, the ANN model is the better machine learning model in this study because its accuracy, sensitivity and specificity are consistently higher than those of the best SVM model. In conclusion, judging from the promising prediction accurateness as demonstrated in the results of this study, it is suggested that stuck pipe prediction using machine learning is indeed practical.

The paper explores the hybrid of SVM and system of Artificial Neural Network as the finest binary classification system for calculating the diabetic nature of people in comparison to Support Vector Machine (SVM). In this research, the sets of all the parameters describing the diabetic nature of a person are taken from the laboratories. This approach is chosen so that a better learning method can be used for various problems. The testing results were found to be in accordance with the accepted results that resemble with the direct diagnosis of a physician. The results of this research shows that this hybrid SVM and Artificial Neural Network (ANN) model is more precise than the SVM model. These results of the hybrid SVM and ANN model suggest that it is very effective for the classification of Diabetic and Non Diabetic nature of a person. This paper highlights the concept of Support Vector Machines and its integration with Artificial Neural Network, the two key characteristics with one being the generalization theory of the SVM model that best describes how to select a hypothesis and functions given by Kernel that introduces the idea of non-linearity without the inclusion of the actual algorithm.

Flooding causes several threats with outcomes which include peril to human and animal life, damage to property, and adversity to agricultural fields. Therefore, flood prediction is of prime importance for reducing loss of life and devastation to property. To model complex nature of hydrologic processes artificial neural network (ANN) tool is effectively being utilized for modelling different nonlinear relationships, and has proved to be an appropriate method for flood prediction. Present study investigated relative accuracy of radial basis function neural network (RBFNN) and support vector machine (SVM) models combined with Firefly Algorithm (FA) in predicting river flood discharge and contrasted with that of regular ANN, RBFNN and SVM models. Monthly river flow data of Silchar and Dholai stations located in Cachar district of Assam, India are utilized for the present study. For assessing model performance, coefficient of determination (R2), mean square error (MSE) and root mean square error (RMSE) were measured. Evaluation of outcomes shows that both RBF-FA (radial basis function - firefly algorithm) and SVM-FA (support vector machine - firefly algorithm) hybrid models give more precise forecasting results than RBFNN, FFBPNN (feed forward back propagation neural network) and SVM models. Yet, it can be observed that SVM-FA model give better forecasting outputs with R2 value 0.9818 than RBF-FA model. Results also reveal that simple SVM model performs marginally better than simple ANN model.

A machine learning approach for early warning of cyanobacterial bloom outbreaks in a freshwater reservoir

Wellbore instability is one of the most critical challenges during drilling, often manifested as wellbore collapse, shrinkage, falling rocks, and formation fracturing, which may result in complex problems such as pipe sticking, high torque, mud loss, thus impeding the drilling progress and increasing the cost of the drilling operation. Conventional wellbore stability prediction relies on some deterministic physical models, involving some empirical coefficients which are difficult to determine and often dependent on field experience. In addition, some complex factors, such as natural fractures, cannot be explicitly and quantitatively characterized in existing wellbore stability prediction models. Artificial intelligence technique has shown unique advantages in nonlinear issues. The artificial intelligence technique is used to predict wellbore stability in this study, including artificial neural networks (ANNs) and support vector machine (SVM). The logging data and drilling data were collected from the field. According to the correlation analysis between influencing factors and wellbore enlargement rate, 16 parameters were extracted, such as mud density, formation density porosity, acoustic interval transit time, weight on bit as the input data of the models, and wellbore enlargement rate as output. Both SVM and ANNs models have exceptional performance in predicting wellbore stability. When the kernel of the SVM model is Linear, predictions perform optimally. In the ANNs model prediction results, the result performs optimally when the total number of neurons is 1024 in the hidden layer. Overall, ANNs model performs better than SVM model with a coefficient of determination (R2) of 0.991, therefore it is recommended to apply ANNs to predict wellbore stability. The present analysis supplies knowledge that can be used to predict wellbore stability problems before drilling, optimize drilling parameters, and reduce drilling accidents and costs. INTRODUCTION Wellbore instability refer to a series of responses resulting from mechanical, chemical and other effects of the rock around the wellbore. Wellbore instability is one of the most critical challenges during drilling, often manifested as wellbore collapse, shrinkage, falling rocks, and formation fracturing, which may result in complex problems such as pipe sticking, high torque, mud loss, thus impeding the drilling progress and increasing the cost of the drilling operation.

ABSTRACTAlong with increase in tram traffic, gradual increase in gauge deviation is inevitable. Excessive track gauge is considered as an effective parameter in aggravating the quality of ride as well as the traffic safety of tram services. To ensure a smooth ride, reduce the risk of the train derailment and lower cost of maintenance, preventive maintenance operations are necessary which demand accurate track degradation prediction modelling. In this study, the Melbourne tram network is considered as a case study. Two types of rail tracks including straight segments and curved segments are studied. In order to develop models for gauge degradation prediction, two machine learning models including artificial neural network (ANN) and support vector machine (SVM) are applied. Two indexes including the coefficient of determination (R2) and mean squared error (MSE) are used to evaluate the performance of the proposed models. According to the results, both ANN and SVM models provide acceptable and somewhat similar outcomes. However, the performance of ANN models in predicting gauge deviation of straight segments is slightly better than SVM models. On the contrary, the performance of SVM models in predicting gauge deviation of curved segments is slightly better than ANN models.

GIS-based mineral prospectivity mapping using machine learning methods: A case study from Tongling ore district, eastern China

The present investigation introduces a robust soft computing model by comparing twelve least square support vector machine (LSSVM), six long short-term memory (LSTM), and thirty-six artificial neural network (ANN) models to predict the unconfined compressive strength (UCS) of fine-grained soil. For that purpose, a database of fine content, dry unit weight, porosity, void ratio, degree of saturation, and specific gravity results of 85 soil specimens has been compiled from the literature. 75 and 10 soil specimens were trained and tested for each model. Six training databases have been prepared to analyze the effect of quality and quantity of training database by selecting 50%, 60%, 70%, 80%, 90%, and 100% of 75 soil specimens. The performance comparison demonstrated that the LSTM model (MD 113) requires fewer training datasets (50% of 75) than the LSSVM (MD 102 and MD 108) and ANN (MD 120, MD 127, MD 136, MD139, MD 148, and MD 150) models. Also, it was observed that the nonlinear LSSVM model (MD 108) is unaffected by multicollinearity in training datasets and predicted UCS better than the linear LSSVM model (MD 102). Furthermore, the Levenberg-Marquardt neural network model (MD 120) has outperformed the other ANN models with the root mean square error (RMSE) of 5.1214 N/cm2, the mean absolute error (MAE) of 4.1379 N/cm2, and correlation (R) of 0.9836. The overall performance comparison revealed that the LSTM model is more potent than the LSSVM and ANN models. The LSTM model predicted the UCS of fine-grained soil with the RMSE of 4.7539 N/cm2, the MAE of 4.2461 N/cm2, and R of 0.9880. Conversely, cosine amplitude sensitivity analysis demonstrated that the fine content and dry unit weight influence the prediction of virgin UCS of fine-grained soils.

Flood susceptibility mapping using a novel ensemble weights-of-evidence and support vector machine models in GIS

To develop machine learning (ML) models capable of predicting ICU admission and extended length of stay (LOS) after torso (chest, abdomen, or pelvis) trauma, by using clinical and/or imaging data. This was a retrospective study of 840 adult patients admitted to a level 1 trauma center after injury to the torso over the course of 1 year. Clinical parameters included age, sex, vital signs, clinical scores, and laboratory values. Imaging data consisted of any injury present on CT. The two outcomes of interest were ICU admission and extended LOS, defined as more than the median LOS in the dataset. We developed and tested artificial neural network (ANN) and support vector machine (SVM) models, and predictive performance was evaluated by area under the receiver operating characteristic (ROC) curve (AUC). The AUCs of SVM and ANN models to predict ICU admission were up to 0.87 ± 0.03 and 0.78 ± 0.02, respectively. The AUCs of SVM and ANN models to predict extended LOS were up to 0.80 ± 0.04 and 0.81 ± 0.05, respectively. Predictions based on imaging alone or imaging with clinical parameters were consistently more accurate than those based solely on clinical parameters. The best performing models incorporated imaging findings and outperformed those with clinical findings alone. ML models have the potential to help predict outcomes in trauma by integrating clinical and imaging findings, although further research may be needed to optimize their performance. • Artificial neural network and support vector machine-based models were used to predict the intensive care unit admission and extended length of stay after trauma to the torso. • Our input data consisted of clinical parameters and CT imaging findings derived from radiology reports, and we found that combining the two significantly enhanced the prediction of both outcomes with either model. • The highest accuracy (83%) and highest area under the receiver operating characteristic curve (0.87) were obtained for artificial neural networks and support vector machines, respectively, by combining clinical and imaging features in the prediction of intensive care unit admission.

The rising machine learning (ML) models have become the preferred way for landslide detection based on remote sensing images, but the performance of these models in a sample-free area are rarely concerned in many studies. In this study, we used a cross-validation method (training model in one area and validation in another) to compare the model portability of trained ML models applied in an “off-site” area, as a consideration of the landslide detection ability of these models in sample-free areas. We integrate nighttime light imagery, multi-seasonal optical Landsat time-series and digital elevation data, and we employed support vector machines (SVM), artificial neural networks (ANN) and random forest (RF) models to classify the satellite imagery and identify landslides. Samples of two scenarios generated from two subareas of the Jiuzhaigou disaster-stricken region are used for the cross-application and accuracy evaluation of three ML models. The results revealed that when the trained models are applied in areas outside those in which they were developed, the landslide identification accuracy of these three models has declined. Especially for the SVM and ANN models, the accuracy is greatly reduced and there appears a seriously imbalanced user’s and producer’s accuracy. However, although the performance of the RF model is lower than that of SVM and ANN models in their local area, the RF model exhibits stable portability, and retains the original performance and achieves a satisfactory balance between overestimation and underestimation in “off-site” areas. An additional validation from a new area proved that the landslide detection performance of the RF model with stable portability is higher than that of the SVM and ANN models in “off-site” areas. The results suggest that evaluating the model portability through cross-application can be a useful way to determine the most suitable model for landslide detection in “off-site” areas with a similar geographic environment to model development areas, so as to maximize the accuracy of landslide detection based on limited samples.