Real-time full-field reconstruction and prediction of temperature field evolution stimulated by dynamic tunnel fires using a physics-informed neural network (PINN) assisted by online-updated sparse monitoring data

1-D coupled surface flow and transport equations revisited via the physics-informed neural network approach

Glucocorticoid-induced hypertension affects over 30% of treated patients, yet its underlying mechanisms remain unclear, particularly how glucocorticoids regulate renin within the renin-angiotensin-aldosterone system (RAAS). Modeling these dynamics is difficult because only four dose-response measurements are available at a single 24-h timepoint (36 observations total), while the system depends on roughly eleven biochemical parameters spanning minutes-long receptor interactions to days-long protein secretion. Classical parameter estimation becomes unreliable in this extremely underdetermined setting, and purely data-driven methods offer limited biological interpretability. In this paper, we introduce a physics-informed neural network (PINN) framework that integrates ELISA measurements from As4.1 juxtaglomerular cells, ordinary differential equations describing glucocorticoid receptor signaling and renin transcription, and automatic differentiation to enforce mechanistic constraints. By systematically tuning synthetic-data weights (SW in {0.2, 0.3, 0.5}), we identify an intermediate value of SW = 0.3 that provides the best overall balance between predictive accuracy, accepted ensemble size, and biologically plausible parameter estimates among the tested configurations. The framework uses adaptive constraint scheduling with a plateau ramp to reduce premature convergence and introduces calibrated plausibility thresholds reflecting experimental noise. The accepted PINN ensemble (n = 5, 50% success rate) achieved R2 = 0.803, compared with 0.759 for the SW = 0.5 baseline and −0.220 for the ODE-only baseline, with RMSE = 0.024. Key learned parameters (IC50 = 2.925 ± 0.012 mg/dL, Hill = 1.950 ± 0.009) are biologically plausible within the model assumptions, and the best single accepted model attained R2 = 0.891. Information criteria favored the PINN over the ODE model, with improvements of approximately 77× (AIC) and 5.9× (BIC). Despite training on a single timepoint, the PINN also infers full 48-h trajectories and reproduces non-monotonic dose-response behavior. This work presents, to our knowledge, the first PINN framework for glucocorticoid-mediated renin regulation and should be interpreted as a proof-of-concept approach for integrating sparse biomedical data with mechanistic constraints. The inferred parameters and temporal dynamics are best viewed as model-dependent, hypothesis-generating estimates rather than validated biological quantities.

A Physics-Informed Neural Network (PINN) was developed to solve the complex Navier-Stokes (N-S) equations for multiphase flow measurement including flowrates of individual phases in the multiphase mixture, and phase ratios. The results were compared against a mathematical based multiphase flow measurement approach and validated through a controlled loop test using oil, water, and gas. The PINN embeds fundamental fluid dynamics principles into its learning process, ensuring that the neural network adheres to the governing physical laws of motion, continuity, and conservation. Unlike traditional neural networks that rely solely on data-driven learning, PINNs incorporate fluid dynamics driven differential equations, to enhance model accuracy and reliability. This study evaluates the accuracy, efficiency, and repeatability of PINNs by comparing their results against traditional mathematical-based multiphase flow measurement (MPFM) technology and controlled test cases. The developed PINN successfully solved the Navier- Stokes (N-S) equations in their closest approximation to the original form, with minimal assumptions and simplifications, to estimate multiphase flow rates, integrating fundamental fluid dynamics principles into its learning process. The results demonstrated that the PINN-based approach achieved accuracy comparable to traditional mathematical multiphase flow measurement (MPFM) technologies, while significantly improving computational efficiency. During controlled loop tests with oil, water, and gas, the PINN model consistently captured flow dynamics with high precision, validating its effectiveness under real-world conditions. Moreover, the PINN method exhibited strong generalization capabilities, adapting to various flow regimes without the need for extensive empirical calibration. Compared to conventional MPFM technologies, PINN reduced reliance on predefined correlations and offered greater adaptability to changing fluid properties. The repeatability of results confirmed the model's reliability, positioning PINNs as a promising alternative for complex multiphase flow measurement applications. These findings highlight the potential of PINNs as an innovative, physics-guided, and data-efficient solution, effectively bridging the gap between traditional physics-based methods and modern machine learning techniques. This paper presents an innovative application of Physics-Informed Neural Networks (PINNs) for multiphase flow measurement, offering a data-driven yet physics-guided alternative to traditional mathematical MPFM technologies. By embedding fundamental physical laws into the neural network training process, the proposed approach enhances accuracy, computational efficiency, and adaptability, while minimizing reliance on extensive empirical calibration. This advancement significantly improves real-time flow monitoring, equipping practicing engineers with a more reliable, data-efficient, and scalable solution for complex multiphase flow measurement in industrial applications.

As Li-ion batteries become more essential in today's economy, tools need to be developed to accurately and rapidly diagnose a battery's internal state-of-health. Using a Li-ion battery's (high-rate) voltage response, it is proposed to determine a battery's internal state through Bayesian calibration.However, Bayesian calibration is notoriously slow and requires thousands of model runs. To accelerate parameter inference using Bayesian calibration, a surrogate model is developed to replace the underlying physics-based Li-ion model. Developing a surrogate model for rapid Bayesian calibration analysis is discussed for both the single particle model (SPM) and the pseudo two-dimensional (P2D) model.Surrogate models are constructed using physics-informed neural networks (PINNs) that encode the influence of internal properties on observed voltage responses. In practice, a neural network can be trained by: 1) using simulation results of the physics-based model (i.e., a data-loss approach); 2) using the residuals of the governing equations themselves (i.e., a physics-loss approach); or 3) using a combination of simulation results and governing equation residuals. In the present work, PINNs are developed using a variety of training losses and neural network architectures. In this analysis, it is shown that a PINN surrogate model can be reliably trained with only physics-informed loss. However, using a coupled data-informed and physics-loss approach produced the most accurate PINNs. Figure~\\ref{fig:spm_2d} illustrates the absolute relative errors of trained PINN networks using several different training losses and neural network architectures.After determining a consistent training strategy for both the SPM and P2D PINN surrogate models, the PINNs are extended to determine additional internal state-of-health parameters. As more and more parameters were introduced, the PINN training suffered from ``the curse of dimensionality", which was mitigated by using a hierarchical training approach (where a PINN trained with fewer variable model parameters was used to train a PINN with more variable model parameters).Next, the high-dimensionality PINN surrogates are then integrated into Bayesian calibration schemes to identify internal Li-ion battery properties from experimentally measured voltages. Interpreting the high-dimensional parameter posteriors is discussed with respect to model error, parameter prior choices, and experimental errors. Figure 1

Thermal deformation is a critical factor affecting the precision of machine tools, requiring accurate thermal modeling to predict temperature fields and thermal parameters. Traditional approaches, such as the Finite Element Method (FEM), require well-defined boundary conditions, which are often unknown or difficult to measure in real machining environments. This paper explores the use of Physics-informed neural networks (PINNs) as an alternative method for solving steady-state heat conduction problems in two dimensions. PINNs integrate sparse sensor data with physical laws, enabling temperature field prediction and convection coefficient estimation without the need for fully specified boundary conditions. We evaluate five different PINN models, varying the balance between data-driven and physics-informed constraints. Results show that enforcing the heat equation alone yields high accuracy in temperature prediction, but accurate convection coefficient estimation requires explicit enforcement of convection conditions. While PINNs successfully infer missing parameters, their sensitivity to temperature gradients can impact accuracy. Additionally, the need for retraining PINNs when conditions change limits real-time applicability, making them more suitable for offline thermal analysis rather than adaptive modeling in dynamic environments.

Long-distance open-channel water diversion projects, such as China’s South-to-North Water Diversion Project, have significantly mitigated regional water supply-demand imbalances. However, the hydraulic behavior of open channels during water conveyance is highly complex, particularly under abnormal conditions like extreme weather or equipment failures, which can cause abrupt hydraulic changes, rapid water level rises, and even local overtopping or other safety hazards. Therefore, global, real-time, and accurate monitoring of open-channel hydraulics is essential to ensure the project's safe and efficient operation. Hydraulic characteristics of open channels are typically obtained through hydrological monitoring systems and numerical simulations. The reasonable placement and number of monitoring sections in a hydrological system are crucial for balancing monitoring accuracy and construction costs across the entire open channel. Numerical simulation accuracy and reliability depend on clear boundary conditions, precise Manning roughness coefficients, and other key parameters. However, these parameters can vary over time and are often difficult to determine in practical applications. Physics-Informed Neural Networks (PINNs) provide an effective solution to these challenges. This study develops a PINN model to predict the hydraulic characteristics of unsteady flow in open channels by integrating sparse hydrological data with physical laws. The study also examines how the number and placement of monitoring sections affect the accuracy of hydraulic predictions for the entire channel. Results demonstrate that PINNs can achieve high-precision hydraulic predictions along the channel using data from only three optimally placed monitoring sections, with average relative L2 errors below 0.5%. PINNs exhibit strong generalization across diverse boundary conditions, accurately predicting complex flow scenarios and demonstrating significantly higher noise resistance compared to traditional methods. Even with Gaussian noise levels of 10%, PINN predictions maintain relative L2 errors within 3%. Furthermore, PINNs show substantial potential for inverting key parameters such as the Manning roughness coefficient. PINNs offer an efficient and rapid approach to hydraulic predictions for long-distance water conveyance projects, aiding in the design and optimization of monitoring systems while minimizing the number of sensors, equipment, and costs.

Assimilating field data is essential to calibrate rock properties in hydrogeological applications. While such workflows are challenging for physics‐based reservoir simulators, data‐driven Artificial Neural Networks (ANN) offer a potential solution by effectively managing noisy data to infer fluid pressure diffusion p ( x , t ). Nevertheless, the sparse observation wells in hydrogeology projects make training ANN models difficult. Therefore, we employ Physics‐Informed Neural Networks (PINN) to bridge this gap between sparse spatial data. We train both ANN and PINN on a synthetic p ( x , t ) data set within a low‐permeability porous medium containing a highly permeable material. Having an identical architecture, both models integrate direct observations of the target variable, while the PINN further optimizes the diffusion equation residual. By comparing the model output as a function of the number of observation wells, we find that the PINN outperforms the ANN when spatial observations are limited to a small number of wells. Adding noise to the training data further underscores the robustness of PINN against random measurement errors or ambient noise. Furthermore, we evaluate the effectiveness of PINN in representing a high‐permeability zone without observations inside the domain. The findings suggest that accuracy is maintained even with reduced thickness of the equivalent material, although this leads to an increase in computation time. Given the sparsity of observation wells in hydrogeological applications, PINNs potentially provide a more suitable machine learning workflow than purely data‐driven ANN for reservoir modeling.

In recent engineering applications using deep learning, physics-informed neural network (PINN) is a new development as it can exploit the underlying physics of engineering systems. The novelty of PINN lies in the use of partial differential equations (PDE) for the loss function. Most PINNs are implemented using automatic differentiation (AD) for training the PDE loss functions. A lesser well-known study is the use of finite difference method (FDM) as an alternative. Unlike an AD based PINN, an immediate benefit of using a FDM based PINN is low implementation cost. In this paper, we propose the use of finite difference method for estimating the PDE loss functions in PINN. Our work is inspired by computational analysis in electromagnetic systems that traditionally solve Laplace’s equation using successive over-relaxation. In the case of Laplace’s equation, our PINN approach can be seen as taking the Laplacian filter response of the neural network output as the loss function. Thus, the implementation of PINN can be very simple. In our experiments, we tested PINN on Laplace’s equation and Burger’s equation. We showed that using FDM, PINN consistently outperforms non-PINN based deep learning. When comparing to AD based PINNs, we showed that our method is faster to compute as well as on par in terms of error reduction.

Adaptive transfer learning for PINN

3D concrete printing (3DCP) is an innovative construction method that extrudes cementitious materials layer-by-layer to fabricate building components based on a digital model. 3DCP has gained increasing adoption globally for projects like buildings, bridges, retaining walls, and stormwater management systems. However, 3DCP places stringent demands on the rheological properties of the printable cementitious materials. Rheology is critical for the flow and buildability of fresh concrete during extrusion. The mixture must have a low yield stress for pumping, moderate viscosity to hold its shape after deposition, minimal bleeding and segregation of aggregates, as well as responsive rheology that can transition from fluid to solid state as layers are printed sequentially. In this dissertation, we aim to solve the challenges mentioned above including: (1) accurate and efficient quantification of rheological and thixotropic properties of cementitious materials, (2) evaluation of flow behavior of fresh concrete during extrusion. Using traditional experimental methods to evaluate rheological properties of cement paste is labor-intensive and time-consuming. Numerical simulations like Finite Element Method (FEM) or Computational Fluid Dynamics (CFD) can help increase the speed of finding the most suitable material for 3DCP. However, these simulation methods are costly in computing power, making them less desirable for simulating the dynamic and complex process of 3DCP. Moreover, mesh-based approaches are not suitable for complex geometries as the mesh generation would be challenging with curved boundaries, small features, holes or thin regions. Physics-Informed Neural Network (PINN) is introduced in the work as an innovative solution to simulate and model the whole process of 3DCP. It can leverage the flexibility and computational efficiency of data-based neural networks, which can accelerate the learning and convergence speed. At the same time, Partial Differential Equations (PDEs) would be embedded in the network structure to increase the accuracy of its prediction. The integrated governing physical laws can help the neural network understanding the underlying physics of the 3DCP process, potentially increasing the accuracy and reliability of simulations. A significant part of the research is dedicated to understanding the rheological and thixotropic behavior of cementitious materials, which is critical for the material design in 3DCP. We developed a Rheology-informed Neural Network, RheologyNet, where we embedded the rheological constitutive laws into the loss function. These physical laws can help the network focus on simulating the rheological properties of cementitious materials. Moreover, a thixotropic evaluation system has been established based on the proposed model to evaluate the thixotropic property of cement paste. This study is presented in Chapter 2. Then, we proposed a Navier-Stokes Informed Neural Network (NSINN) to study the flow behavior of cement paste in the 3DCP barrel and nozzle since it involves complicated Multiscale or Multiphysics behaviors, such as anisotropy and non-uniform shear rate distribution. The Navier Stokes Equation and the rheological constitutive equations are coupled and embedded into the NSINN architecture to simulate the flow behavior in the barrel during 3D-printing extrusion process. This approach demonstrates the potential of PINNs to provide high-accuracy simulations of velocity and pressure fields in a computationally efficient manner compared to traditional mesh-based models. Also, we used the NSINN to learn the relationship between the nozzle size and the printing quality. The details of the study are presented in Chapter 3. At last, a multi-subnetwork PINN architecture (MultiSubPINN) is proposed to address the limitations of traditional PINNs. This is because traditional PINNs used Fully-connected Neural Network (FNN) as main bone. It has problems like different outputs must share parameters within the network structure. However, this parameter sharing nature might lead to potential errors and decrease the model performance. The main architecture of this network is consisted of multiple separated sub-networks and the loss function of each sub-network is calculated separately to update the parameters in each sub-network. By doing this, we can ensure that the optimization for one output doesn't negatively impact others, therefore providing a more flexible, scalable, and potentially more accurate alternative for the evaluation. Besides, using randomly distributed training points in the computational domain for PINNs is a common way. However, many physical problems exhibit non-uniform behavior, with certain regions of the domain having more complex dynamics or sharper gradients than others. Randomly distributed training points might not adequately capture these regions, leading to a model that misrepresents the underlying physics in critical areas. We proposed a Physical-based sampling strategy to optimize the training of the PINNs. This study is presented in Chapter 4. In summary, this dissertation has established a new platform that is enabled by interpretable NN to accurately quantify cement paste’s rheological properties and simulate the flow behavior of 3D concrete printing process. The findings suggest that PINNs can not only improve the efficiency and accuracy of simulations but also provide a more profound understanding of the material behaviors and process dynamics critical to 3DCP. The novel PINN structure developed from this dissertation is a powerful general platform that could be applicable to a variety of material domains for complex rheological behavior predictions.

A novel sequential method to train physics informed neural networks for Allen Cahn and Cahn Hilliard equations

The accurate modeling of the Earth gravity field and geoid is critical for geodesy, yet traditional methods face limitations in handling the growing complexity and heterogeneity of modern geodetic data. To address these challenges, this study proposes a physics-informed neural network (PINN) framework for high-precision geoid modeling. The PINN employs convolutional neural networks (CNNs) to extract multi-scale features from terrestrial and airborne gravity data, which are then processed by a multilayer perceptron (MLP) to establish an accurate mapping between these features and the disturbing potential. Physical constraints, including Laplace’s equation and differential equations governing gravity anomaly and gravity disturbance, are embedded into the loss function to enhance both accuracy and interpretability. The proposed method is applied to the Colorado 1 cm geoid experiment. Compared to GNSS/leveling data of the Geoid Slope Validation Survey 2017 (GSVS17), the PINN-derived geoid model achieves a standard deviation (STD) of 2.1 cm. This represents a 12.5%–27.6% improvement over traditional methods and purely data-driven networks (DDNs). The PINN exhibits strong generalization under sparse data conditions, achieving 28.5% higher accuracy than the DDN with only 500 samples. Furthermore, analysis of geoid slopes and physical constraint contributions demonstrates that PINN’s dual physical constraints effectively balance global characteristics and localized fidelity of the geoid. This study establishes the PINN as a robust, physically interpretable machine learning approach for geoid modeling, outperforming classical methods and offering a promising pathway for gravity field estimation in regions with sparse or heterogeneous data. By bridging purely data-driven machine learning with fundamental geodetic principles, this work paves the way for future advancements in physics-informed machine learning-based geodetic modeling.

This thesis investigates two physics informed neural network (PINN) approaches for two mechanistic problems via the performance metrics of model parameter estimation and system state prediction. The PINNs are compared to Bayesian inference (BI) tested under similar conditions. The first PINN studied is the loss-based PINN, which embeds physics into a standard feedforward neural network within the loss function of this network. The second PINN investigated is the hybrid-recurrent physics informed neural network, which uses a recurrent neural network (RNN) that embeds physics in RNN architecture. The BI used as a point of comparison uses a Transitional Markov Chain Monte Carlo algorithm to estimate the posterior distributions. The applications studied are a compartmental model for an infectious disease, and a mass-spring-damper model. It is found that BI performs better in ideal data conditions and the PINNs perform better in weak data conditions.

Physics-Informed Neural Network for modeling and predicting temperature fluctuations in proton exchange membrane electrolysis

Physics-informed neural networks (PINNs) are emerging as a promising artificial intelligence approach for solving complex two-phase flow simulations. A critical challenge in these simulations is an accurate representation of the gas–liquid interface using interface tracking methods. While numerous studies in conventional computational fluid dynamics (CFD) have addressed this issue, there remains a notable absence of research within the context of PINNs-based two-phase flow simulations. Therefore, this study aims to develop a robust and generic PINNs for two-phase flow by incorporating the governing equations with three advanced interface tracking methods—specifically, the Volume of Fluid, Level Set, and Phase-Field method—into an improved PINN framework that has been previously proposed and validated. To further enhance the performance of the PINNs in simulating two-phase flow, the phase field constraints, residual connection and the time divide-and-conquer strategies are employed for restricting neural network training within the scope of physical laws. This self-adaptive and time divide-and-conquer (AT) PINNs is then optimized by minimizing both the residual and loss terms of partial differential equation. By incorporating the three different interface tracking methods, it efficiently handles high-order derivative terms and captures the phase interface. The case of single rising bubble in two-phase flow is simulated to validate the robustness and accuracy of the AT PINNs. The simulation's accuracy is evaluated by comparing its performance in terms of velocity, pressure, phase field, center of mass, and rising velocity with that of conventional PINNs and CFD benchmarks. The results indicate that the AT PINNs coupled with these interface tracking methods offers a satisfactory performance in simulating rising bubble phenomenon.