Research on Flexible Joint MPC Optimization Control Method Based on Joint Drive Parameter Identification

Multi-vector model predictive control of permanent magnet synchronous motor can effectively overcome the shortcomings of conventional single-vector model predictive control such as large motor current ripples and limited control accuracy, but its control performance is more susceptible to the influence of motor parameter perturbation. To improve the robustness of the multi-vector predictive control algorithm under the motor parameter perturbation, a novel nonparametric three-vector model predictive current control method for permanent magnet synchronous motors is proposed in this paper. Through constructing an ultra-local predictive current model based on the input and output signals of the permanent magnet synchronous motor, the influence of motor parameter perturbation on current prediction is avoided, and a disturbance observer is designed to estimate the non-modeled and perturbed parts of the ultra-local model. In addition, the direct calculation method of vector duty cycles based on current error is introduced to suppress the influence of motor parameter uncertainty on the duty cycle calculation link, which further improves the system robustness. Finally, simulations and experiments of the proposed method are demonstrated to compare with the conventional parametric three-vector model predictive current control, and the results show that the proposed control strategy can effectively suppress the disturbances caused by the motor parameters and ensure the steady-state performance during motor operation.

The model predictive control method can be effective for converter control in distributed power generation but requires a large amount of computation, leading to a considerable time delay in the actuation. If the delay is not reflected, the system performance could get worse. This paper presents a two-step (horizon) prediction algorithm of model predictive control technique for grid-tied inverters used in wind turbine systems. The control objectives such as active and reactive power flow and switching loss reduction are reflected in the objective function of the controller. The proposed model predictive control strategy is verified numerically by using MATLAB/Simulink.

To improve the dynamic and steady-state control performance of permanent magnet synchronous motors under the three-vector model predictive current control method, this study proposes a switching current predictive control method based on the exponential moving average algorithm, which evaluates the magnitude of the change of the q-axis current slope in real time to discriminate the motor’s operating conditions and selects the optimal control method for different operating conditions. Meanwhile, the traditional three-vector model predictive current control method is improved by introducing a comparison mechanism for the q-axis current slope to select the second effective voltage vector, avoiding the secondary optimization calculation of the value function and reducing the computational complexity of the traditional method. By comparing the proposed method with the traditional three-vector model predictive current control method, the experimental results prove that the proposed method improves the system’s dynamic response and steady-state performance.

This chapter presents the results of experiments comparing different computationally efficient model predictive control (MPC) methods applied to a laboratory device, demonstrating the active vibration control (AVC) of lightly damped mechanical structures. Because of the combination of long prediction horizons, short sampling times and large actuator-disturbance asymmetry, the implementation of the predictive control strategy on lightly damped vibrating structures is highly demanding. The vibration damping effect and online timing properties of model predictive control algorithms such as infinite horizon cost dual-mode quadratic programming based MPC (QPMPC), pre-computed explicit multi-parametric programming based MPC (MPMPC), minimum-time MPMPC and the very efficient but suboptimal Newton–Raphson based MPC (NRMPC); all with guaranteed stability and constraint feasibility are analyzed in different disturbance and loading scenarios. All MPC methods along with the baseline linear quadratic (LQ) controller decrease vibration settling to equilibrium by an order of magnitude time. The damping effect of all investigated MPC strategies is comparable with a slight decrease in performance for the suboptimal minimum-time MPMPC and NRMPC controllers. Due to the excessive online computational needs of QPMPC, it is a very unlikely candidate for lightly damped vibrating systems given currently available hardware. The online timing analysis presented here demonstrates that MPMPC provides significantly shorter online execution times, however its suboptimal minimum-time version does not bring a convincing improvement. NRMPC can provide online execution times on par with linear quadratic controllers; however, its suboptimality becomes excessive with increasing prediction model orders.

Comparative Assessment of Alternative Mpc Strategies Using Real Meteorological Data and Their Enhancement for Optimal Utilization of Flexibility-Resources in Buildings

The research on grid-connected inverters (GCI) is gaining momentum as more and more focus is given to clean energy sources like solar photovoltaic (PV) and wind energy. Conventional GCI uses the proportional-integral (PI) controller in conjunction with the sinusoidal pulse width modulation (SPWM) technique for pumping power to the grid. Model predictive control (MPC) is becoming more relevant in the field of power electronics. Conventional MPC uses a single prediction horizon or single step. This paper proposes the estimation of the optimization criterion for more than one prediction horizon, termed a multistep MPC. The multistep MPC is an extension of the basic MPC. The MATLAB/Simulink simulations of the proposed multistep MPC and the conventional single step MPC are presented in this paper. The total harmonic distortion (THD) values are compared between the conventional MPC and multistep MPC for varied operating conditions. The settling time of the controllers as well as the deviations in the cost function are compared. The simulation results indicate a better performance of the multistep MPC in comparison with a conventional single horizon MPC.

This paper proposes a model predictive controller for two-stage inverter with less switching losses and capacitor current. In implementation, model predictive control (MPC) method is simple and flexible without assuming the traditional PWM block. As the capacitor current has great influence on the capacitor losses and lifetime, an adjustment before the switching signals are sent to the switches is added in the proposed MPC method to reduce the capacitor current RMS value. The decrease of capacitor current RMS value enables the reduction of capacitor losses and the increase of capacitor lifetime. Besides, the proposed method can achieve less switching losses of front-end dc-dc converter, compared with the conventional MPC method. This paper presents the detailed operational principle of proposed MPC method and compares the performance of conventional and proposed MPC methods using the same system parameters. Finally, the simulation and experimental results verified the validity and advantage of the proposed method.

In this paper, using the two control methods of model predictive control (MPC), model predictive current control (MPCC) and model predictive torque control (MPTC) is applied to the control system of permanent magnet synchronous motor(PMSM). The algorithms are based on the minimization of different cost functions, and the corresponding optimal voltage vector can be obtained. Comparison of the dynamic and steady state performance of the tested PMSM with MPCC and MPTC is elaborated. The delay compensation is considered to reduce the fluctuation of current and torque, in order to reduce the computational burden by using a single vector, comparison of two methods in the speed control system of dynamic and steady-state performance and speed tracking performance and resistance to load disturbance. The simulation results show that both MPCC and MPTC can be well applied to the PMSM driving systems with good speed tracking performance. However the MPCC can achieve less harmonics in the stator currents, and consequently the circular flux linkage trajectory is smoother, while the MPTC shows advantages in smaller ripples in the mechanical torque.

This paper proposes a highly efficient single-phase three-level neutral point clamped (NPC) converter operated by a model predictive control (MPC) method with reduced commutations of switches. The proposed method only allows switching states with none or a single commutation at the next step as candidates for future switching states for the MPC method. Because the proposed method preselects switching states with reduced commutations when selecting an optimal state at a future step, the proposed method can reduce the number of switchings and the corresponding switching losses. Although the proposed method slightly increases the peak-to-peak variations of the two dc capacitor voltages, the developed method does not deteriorate the input current quality and input power factor despite the reduced number of switching numbers and losses. Thus, the proposed method can reduce the number of switching losses and lead to high efficiency, in comparison with the conventional MPC method.

This paper presents centralized control for a wind farm using model predictive control (MPC) method. In order to solve intra-day unit commitment (UC) problem, the UC problem is solved by using the MPC method with short-term wind power forecasting. We introduce a new dynamics model for the UC with some constraints to utilize the benefits of the MPC method. The objective function considering the operation and maintenance costs is formulated by adding a new variable in order to average the operating time of each wind turbine (WT) within the whole time. The proposed method could solve the UC problems on-line using the prediction time horizon that could be selected flexibly considering time horizon based on wind power forecasting errors. From the simulation study using 10 WTs, we observed that the proposed dynamics model of UC effectively provided the optimal solution to each scenario. Numerical study will validate that the proposed method can be applied to solving the UC problem of a large scale wind farm by aggregating WTs.

This article proposes an improved model predictive control (MPC) method for high-power current-source rectifiers (CSR). Instead of introducing the virtual impedance based active damping notion into MPC framework, the predefined cost function directly takes grid-side current and capacitor voltage as the regulating objectives to suppress the $LC$ resonance and grid current distortions. The relationship and differences between the proposed cost function and its form with active damping function are analyzed in detail under normal grid conditions. Moreover, the number of discrete candidate vectors during each predictive horizon in the proposed scheme is reduced from nine to five by considering the constraint of switching states transition. Therefore the computational burden is relieved compared with conventional MPC under normal grid conditions. Finally, in order to keep sinusoidal grid current for CSR even working under severe distorted supply voltage, specific harmonic orders of grid current suppression items are added into the proposed cost function subsequently. The performance of proposed methods at low switching frequency ( $\leq$ 1 kHz) under normal and distorted grid conditions are tested through both simulation and experiments. For the implementation of all MPC methods, capacitor voltage is estimated by an observer to save hardware expense instead of using transducers.

To address the complexity of vector selection in the conventional predictive current control strategy and the reduction of control system robustness when the motor parameters change, this paper proposes a finite-set model-free three-vector predictive current control method for permanent magnet synchronous motor based on the improved sliding-mode perturbation observer. According to the mathematical model of a permanent magnet synchronous motor under perturbation, a new hyperlocal model is established, and the conventional vector traversal optimization method is optimized to obtain the necessary basic voltage vector by analyzing the function with one judgment. Meanwhile, the sliding mode perturbation observer is designed using the fast exponential convergence law to observe the unknown part. Finally, by experimentally contrasting the proposed technique with the conventional three-vector model predictive current control, the method suggested in this paper can successfully reduce the current pulsation and inhibit the system perturbation caused by the parameter change, ensuring the steady state performance of the motor, as demonstrated by the experimental comparison with the conventional three-vector model predictive current control method.

Three-phase AC/DC pulse-width-modulated (PWM) converters have been widely employed in various renewable energy systems and industrial applications, which require a high-efficiency power converter operation. This article proposes a technique to reduce switching loss in AC/DC converters by integrating a voltage vector preselection strategy to model predictive virtual flux control. The voltage vector preselection strategy preselects available voltage vectors corresponding to switching states that lead to minimum switching loss in the phase leg, which conducts the highest current. By using preselected voltage vectors, clamping intervals are generated at every fundamental period to maintain the present switching states of the power switches, resulting in the reduction in switching loss. Additionally, by using virtual flux control, the proposed approach can effectively be used under both ideal and distorted source voltage conditions. The proposed method is compared with the conventional model predictive current control and the conventional model predictive virtual flux control. Both a simulation and experiment are performed to validate the correctness and effectiveness of the proposed method, which has been found to decrease the switching loss of an AC/DC converter by up to 15% compared to conventional control schemes at a negligible increase in the input current total harmonic distortion and DC output voltage ripple.

Vienna rectifier, which is a nongenerative-boost-type rectifier, is widely employed in electric vehicle charging systems. Nevertheless, the Vienna rectifier faces the challenge of current distortion elimination, current ripple mitigation, and neutral-point (NP) voltage balance. As these problems are mutually coupled, the conventional finite control set model predictive control (FCS-MPC) methods cannot solve these problems properly. To address these issues, a three-layer double-vector FCS-MPC method is proposed. In the first layer of the proposed FCS-MPC method, the sectors are divided and the candidate vectors are selected to reduce the current distortion. In the second layer of the proposed FCS-MPC method, the double vectors with optimal duty cycles are adopted to reduce the current ripples. In the third layer of the proposed FCS-MPC method, the NP voltage is balanced by selecting the redundant p-type small vector or n-type small vector. Through the proposed method, the current distortion elimination, current ripple mitigation, and NP voltage balancing are realized at the same time. The effectiveness of the proposed method has been verified by simulation and experiment.

This paper proposes a time-lag model predictive control (MPC) method to solve the problem of communication delay in networked automatic generation control (AGC). The method uses the optimum weighting method to predict delay and the time-lag dynamic state equation of interconnected grid as the MPC prediction model. Then the deviation of predicted output is added to the objective function of rolling optimization in MPC method. The backup suboptimal control command from MPC controller can handle the loss of data packet in networked AGC. The correctness of the proposed method is verified by dynamic simulation.