Resource Allocation Based on Task Priority and Resource Consumption in Edge Computing

SummaryRecently, the deployment of novel smart network concepts, such as the Internet of things (IoT) or machine‐to‐machine communication, has gained more attention owing to its role in providing communication among various smart devices. The IoT involves a set of IoT devices (IoTDs) such as actuators and sensors that communicate with IoT applications via IoT gateways without human intervention. The IoTDs have different traffic types with various delay requirements, and we can classify them into two main groups: critical and massive IoTDs. The fundamental promising technology in the IoT is the advanced long‐term evolution (LTE‐A). In the future, the number of IoTDs attempting to access an LTE‐A network in a short period will increase rapidly and, thus, significantly reduce the performance of the LTE‐A network and affect the QoS required by variant IoT traffic. Therefore, efficient resource allocation is required.In this paper, we propose a priority‐based allocation scheme for multiclass service in IoT to efficiently share resources between critical and massive IoTD traffic based on their specific characteristics while protecting the critical IoTDs, which have a higher priority over the massive IoTDs. The performance of the proposed scheme is analyzed using the Geo/G/1 queuing system focusing on QoS guarantees and resource utilization of both critical and massive IoTDs. The distribution of service time of the proposed system is determined and, thus, the average waiting and service times are derived. The results indicate that the performance of the massive IoTDs depends on the data traffic characteristics of the critical IoTDs. Furthermore, the results emphasize the importance of the system delay analysis and demonstrate its effects on IoT configurations.

Edge computing provides cloud services at the edge of the network for Internet of Things (IoT) devices. It aims to address low latency of the network and alleviates data processing of the cloud. This “cloud-edge-device” paradigm brings convenience as well as challenges for location-privacy protection of the IoT. In the edge computing environment, the fixed edge equipment supplies computing services for adjacent IoT devices. Therefore, edge computing suffers location leakage as the connection and authentication records imply the location of IoT devices. This article focuses on the location awareness in the edge computing environment. We adopt the “deniability” of authentication to prevent location leakage when IoT devices connect to the edge nodes. In our solution, an efficient deniable authentication based on a two-user ring signature is constructed. The robustness of authentication makes the fixed edge equipment accept the legal end devices. Besides, the deniability of authentication cannot convince any third party that the fact of this authentication occurred as communication transcript is no longer an evidence for this connection. Therefore, it handles the inherent location risk in edge computing. Compared to efficient deniable authentications, our protocol saves 10.728% and 14.696% computational cost, respectively.

The proliferation of Internet of Things (IoT) devices in personal and household environments has led to a significant increase in security vulnerabilities. These devices, due to their limited computational resources, often struggle to support conventional security solutions, making them prime targets for cyberattacks. This paper explores the potential of lightweight machine learning (ML) models to enhance the security of personal IoT devices. By leveraging the power of AI, lightweight models can offer real-time threat detection and anomaly identification without compromising the device's performance or requiring extensive computational resources. The paper investigates various ML techniques that are well-suited for IoT environments, such as decision trees, k-nearest neighbours (KNN), and support vector machines (SVM), focusing on their ability to detect intrusions, unauthorized access, and other malicious activities while maintaining efficiency. Additionally, the study highlights the trade-offs between model complexity, accuracy, and resource consumption, offering practical insights for deploying ML solutions in resource-constrained IoT systems. Key challenges, including data privacy, model generalization, and the adaptability of models to diverse IoT ecosystems, are addressed. Finally, the paper discusses future directions for the integration of more advanced lightweight models, such as federated learning and edge computing, which could further enhance security capabilities while ensuring minimal impact on IoT device performance. Through this review, the paper advocates for the adoption of lightweight ML models as a feasible and scalable solution to securing personal IoT devices in an increasingly connected world.

The Internet of Things (IoT) devices is able to communicate with another IoT devices in heterogeneous environments. They are also able to create a network by their own using wireless capabilities without a centralized approach. This network is called wireless mobile ad hoc network (MANET). The MANET facilitate IoT devices to communicate with each other in an infrastructure less network of the Internet of Things environment. The IoT devices can dynamically join, create connection and exchange information among them. The role of cloud in this framework is to store and process the data by IoT devices. The communication Security has been raised as one of the most critical issues of cloud computing where resolving such an issue would result in a constant growth in the use and popularity of cloud. Our purpose of this study is to create a framework for providing the communication in an integrated framework of Cloud and MANET among IoT devices. Our main contribution links a new study that integrates cloud computing to the MANET and provides communication to the internet of things. This study can be used in the framework of the Internet of Things in future.

The Internet of Things (IoT) has had a considerable influence on our daily lives by enabling enhanced connection of devices, systems, and services that extends beyond machine-to-machine interactions and encompasses a wide range of protocols, domains, and applications. However, despite privacy concerns shown by IoT users, little has been done to reduce and protect individual information exposure. It is extremely difficult to mitigate IoT devices from reidentification threats which is why it is still a major challenge for IoT users to securely protect their information. The trust controls how we regulate privacy in our IoT platforms in the same way that it governs personal relationships. As IoT devices become increasingly linked, more data is shared across individuals, businesses, governments, and ecosystems. Technologies, sensors, machines, data, and cloud connections all rely largely on trust relationships that have been formed. With the rapid growth of additional types of IoT devices that are being introduced, it, therefore, expands privacy concerns and is difficult to develop trust with an IoT system or device without the option to regulate information privacy settings. Privacy has always been a barrier for many devices as they race for the early adoption of IoT technologies. Several Internet of Things devices or systems will continue to pose privacy threats. As a result, the main objective of this study was to examine the individual understanding of privacy and to promote information privacy protection awareness not only to IoT users but also to organizations that use IoT devices or platforms to run their day-to-day business operations. Furthermore, the objective extends to compare user knowledge and concerns about IoT privacy, as well as to identify any common attitudes and variances. However, in terms of enhancing individuals’ knowledge, an artifact was developed to educate and enhance information privacy awareness among IoT users. A pre- and postquestionnaire was generated to test and validate user knowledge regarding information privacy protection in IoT. The study was conducted using a quantitative research method. Findings indicate that IoT users’ awareness of information privacy protection turned out to be average, suggesting a need for education and awareness. Several participants stated that information privacy protection awareness is required within the community to educate, raise awareness, eliminate human error, and enable individuals to be conscious of their privacy when surfing the Internet.

Seeing is not always believing: Insights on IoT manufacturing from firmware composition analysis and vendor survey

With the advancement in science and technology, the demand for electronic Internet of Things (IoT) devices has increased to store and process digital data. With the advancement in IoT technology, we are more reliant on IoT devices to perform our regular tasks. IoT Forensics deals with the investigation of IoT devices such as smartphones, tablets, smart watches, or any device which is connected to the Internet. The data on these devices can still be retrieved via IoT forensics even if they are destroyed, resold, or misplaced. Before discarding any IoT device, we must consider how to secure the data stored on them. We are then going to discuss the several types of personal data that could be retrieved from discarded IoT devices. Finally, we are going to discuss the protection measures for the safe disposal of IoT devices.

UAV-mounted IRS assisted wireless powered mobile edge computing systems: Joint beamforming design, resource allocation and position optimization

With the advancement of 5G mobile telecommunication, various IoT (Internet of Things) devices communicate massive amounts of data by being connected to wireless networks. Since this wireless communication is vulnerable to hackers via data leakage during communication, the transmitted data should be encrypted through block ciphers to protect the data during communication. In addition, in order to encrypt the massive amounts of data securely, it is essential to apply one of secure mode of operation. Among them, CTR (CounTeR) mode is the most widely used in industrial applications. However, these IoT devices have limited resources of computing and memory compared to typical computers, so that it is challenging to process cryptographic algorithms that have computation-intensive tasks in IoT devices at high speed. Thus, it is required that cryptographic algorithms are optimized in IoT devices. In other words, optimizing cryptographic operations on these IoT devices is not only basic but also an essential effort in order to build secure IoT-based service systems. For efficient encryption on IoT devices, even though several ARX (Add-Rotate-XOR)-based ciphers have been proposed, it still necessary to improve the performance of encryption for smooth and secure IoT services. In this article, we propose the first parallel implementations of CTR mode of ARX-based ciphers: LEA (Lightweight Encryption Algorithm), HIGHT (high security and light weight), and revised CHAM on the ARMv8 platform, a popular microcontroller in various IoT applications. For the parallel implementation, we propose an efficient data parallelism technique and register scheduling, which maximizes the usage of vector registers. Through proposed techniques, we process the maximum amount of encryption simultaneously by utilizing all vector registers. Namely, in the case of HIGHT and revised CHAM-64/128 (resp. LEA, revised CHAM-128/128, and CHAM-128/256), we can execute 48 (resp. 24) encryptions simultaneously. In addition, we optimize the process of CTR mode by pre-computing and using the intermediate value of some initial rounds by utilizing the property that the nonce part of CTR mode input is fixed during encryptions. Through the pre-computation table, CTR mode is optimized up until round 4 in LEA, round 5 in HIGHT, and round 7 in revised CHAM. With the proposed parallel processing technique, our software provides 3.09%, 5.26%, and 9.52% of improved performance in LEA, HIGHT, and revised CHAM-64/128, respectively, compared to the existing parallel works in ARM-based MCU. Furthermore, with the proposed CTR mode optimization technique, our software provides the most improved performance with 8.76%, 8.62%, and 15.87% in LEA-CTR, HIGHT-CTR, and revised CHAM-CTR, respectively. This work is the fastest implementation of CTR mode on ARMv8 architecture to the best of our knowledge.

In the past decades, explosive numbers of Internet of Things (IoT) devices (objects) have been connected to the Internet, which enable users to access, control, and monitor their surrounding phenomenons at anytime and anywhere. To provide seamless interactions between the cyber world and the real world, Digital twins (DTs) of objects (IoT devices) are key enablers for real time monitoring, behaviour simulations, and predictive decisions on objects. Compared to centralized cloud computing, mobile edge computing (MEC) has been envisioning as a promising paradigm for low latency IoT applications. Accelerating the usage of DTs in MEC networks will bring unprecedented benefits to diverse services, through the co-evolution between physical objects and their virtual DTs, and DT-assisted service provisioning has attracted increasing attention recently. In this article, we consider novel DT placement and migration problems in an MEC network with the mobility assumption of objects and users, by jointly considering the freshness of DT data and the service cost of users requesting for DT data. To this end, we first propose an algorithm for the DT placement problem with the aim to minimize the sum of the DT update cost of objects and the total service cost of users requesting for DT data, through efficient DT placements and resource allocation to process user requests. We then devise an approximation algorithm with a provable approximation ratio for a special case of the DT placement problem when each user requests the DT data of only one object. Meanwhile, considering the mobility of users and objects, we devise an online, two-layer scheduling algorithm for DT migrations to further reduce the total service cost of users within a given finite time horizon. We finally evaluate the performance of the proposed algorithms through experimental simulations. The simulation results show that the proposed algorithms are promising.

The number of Internet of Things (IoT) devices has increased recently and will increase further in the future. IoT devices are vulnerable, so vendors update and distribute firmware. At the time of firmware distribution, a huge number of IoT devices may connect to the firmware server and excessive network traffic may occur. Consequently, a method using a peer-to-peer file sharing system and a blockchain has been proposed. One study proposed an update scheme considering incentives for distributors to help with updating. However, this method requires the IoT devices, which have limited processing power, to decrypt encrypted files, and the distribution nodes to pay the transaction cost. This paper proposes a firmware distribution method that provides incentives for distributors to help with distribution to reduce the gas costs, using a smart contract and access control based on update records. The additional computations performed by IoT devices and distributors key management were reduced compared to those in previous studies by using access control instead of encryption. Further, the proposed approach was implemented and evaluated using a Raspberry Pi and laptop. The evaluation demonstrated that the gas cost per update was successfully lowered compared to the costs in previous studies.

As location-aware IoT (Internet of Things) devices intend to spread across almost every application, IoT devices are going to require different GNSS (Global Navigation Satellite System) receiver design requirements. To deliver on IoT opportunities, system architects and designers need to look carefully at every aspect of system design and architecture to be able to enable the full potential of the IoT era. IoT devices are equipped with different connectivity sensors that can provide a reliable integrated location-awareness solution. IoT devices are mainly relying on GNSS chip to deliver a service when no other RF signal is available. Hence, GNSS chip is expected to maintain a robust and reliable performance even in harsh environment. The harsh environment includes multipath environment, NLOS (Non-Line of Sight) GNSS signal reception, weak GNSS signal power reception, superimposed motion (e.g., arm swing, floating platform fluctuation …etc.), operation under freezing temperature, and interference. The targeted low-cost system design along with the expected harsh operational environment derived us to face exceptional GNSS signal reception condition. This paper discusses lessons learned, and challenges faced signal acquisition, reacquisition, and tracking for several IoT applications. Different operational modes are also explored to accommodate various use cases scenarios for several IoT applications. These different power consumption operational modes allow the GNSS chip to achieve an Ultra-low power consumption which indeed required for IoT applications. This paper provides an overview about the addressed GNSS chip fabricated in a 28nm FD-SOI process. We demonstrate a system performance and power consumption comparison of this chip along with other state-of-the-art GNSS chip. We compare the positioning performance for this device alongside another state-of-the-art GNSS modules and Novatel’s tightly coupled GNSS/INS (Inertial Navigation System) reference solution at numerous scenarios ranging from walking, running, and driving at several sites under different environment.

ABSTRACTIn recent years, the emerging development of Internet of things (IoT) has created new opportunities for IoT service provider, device manufacturer and customer (end user). In agriculture, employing IoT can help reducing manpower as well as standardizing agricultural processes, thus increasing the benefit for customer who does agricultural business. Beside the opportunities, there are also issues while doing maintenance for an agricultural IoT system. One of them is how to automate the process to detect faults of IoT devices in a large deployment area. While previous studies focus on investigating algorithms as well as theoretical model to detect faults for specific IoT devices, automatically expanding of IoT management process for detecting faults of sensor/actuator has not been investigated yet. To achieve this, we should be able to deal with the relationship between IoT device manufacturer, service provider and customer. In this study, we conceptualize the knowledge of IoT devices, management process and fault detection requirement. To realize this model, we introduce a runtime system to expand the IoT management process for detecting sensor/actuator faults which is able to provide the above features. We do several experiments to show the effectiveness and usefulness of the proposed solution.

In the modern security-conscious world, Deep Packet Inspection (DPI) proxies are increasingly often used on industrial and enterprise networks to perform TLS unwrapping on all outbound connections. However, enabling TLS unwrapping requires local devices to have the DPI proxy Certificate Authority certificates installed. While for conventional computing devices this is addressed via enterprise management, it's a difficult problem for Internet of Things (IoT) devices which are generally not under enterprise management, and may not even be capable of it due to their resource-constrained nature. Thus, for typical IoT devices, being installed on a network with DPI requires either manual device configuration or custom DPI proxy configuration, both of which solutions have significant shortcomings. This poses a serious challenge to the deployment of IoT devices on DPI-enabled intranets. The authors propose a solution to this problem: a method of installing on IoT devices the CA certificates for DPI proxy CAs, as well as other security configuration (security bootstrapping). The proposed solution respects the DPI policies, while allowing the commissioning of IoT and IIoT devices without the need for additional manual configuration either at device scope or at network scope. This is accomplished by performing the bootstrap operation over unsecured connection, and downloading certificates using TLS validation at application level. The resulting solution is light-weight and secure, yet does not require validation of the DPI proxy's CA certificates in order to perform the security bootstrapping, thus avoiding the chicken-and-egg problem inherent in using TLS on DPI-enabled intranets.

The deployment of a client–server-based distributed intelligent system involves application development in both the network domain and the device domain. In the network domain, an application server (typically in the cloud) is deployed to execute the network applications. In the device domain, several Internet of Things (IoT) devices may be configured as, for example, wireless sensor networks (WSNs), and interact with each other through the application server. Developing the network and the device applications are tedious tasks that are the major costs for building a distributed intelligent system. To resolve this issue, a low-code or no-code (LCNC) approach has been purposed to automate code generation. As traditional LCNC solutions are highly generic, they tend to generate excess code and instructions, which will lack efficiency in terms of storage and processing. Fortunately, optimization of automated code generation can be achieved for IoT by taking advantage of the IoT characteristics. An IoT-based distributed intelligent system consists of the device domain (IoT devices) and the network domain (IoT server). The software of an IoT device in the device domain consists of the Device Application (DA) and the Sensor Application (SA). Most IoT LCNC approaches provide code generation in the network domain. Very few approaches automatically generate the DA code. To our knowledge, no approach supports the SA code generation. In this paper, we propose DeviceTalk, an LCNC environment for the DA and the SA code development. DeviceTalk automatically generates the code for IoT devices to speed up the software development in the device domain for a distributed intelligent system. We propose the DeviceTalk architecture, design and implementation of the code generation mechanism for the IoT devices. Then, we show how a developer can use the DeviceTalk Graphical User Interface (GUI) to exercise LCNC development of the device software.