SAR Three-Dimensional Imaging Experiments with Microwave Anechoic Chamber SAR Data

In circular synthetic aperture radar (CSAR), radar collects data over a circular trajectory. This wide-angle non-linear collection geometry makes CSAR capable of obtaining both two-dimensional (2D) high resolution image and three-dimensional (3D) image. In this paper, compressive sensing technique is used in 3D CSAR imaging. Not only echo samples used in imaging are greatly reduced, but also the imaging results are with good performance. However, the consumed time of reconstruction is very long. In order to overcome this problem, graphic process unit (GPU) is furtherly used in 3D compressive sensing CSAR imaging in this paper. Simulation results show that GPU can improve the efficiency of the 3D reconstruction.

Circular synthetic aperture radar (CSAR) has attracted much attention in the field of high-resolution SAR imaging. However, the CSAR image focusing is affected by the motion deviations of platform. In the processing of experimental CSAR data to deal with motion errors, the main way is using setup calibrators, which restricts its widespread applications. In this paper, based on the estimation of motion errors, an autofocus CSAR imaging strategy is proposed without using any setup calibrator. The first step is to split the entire aperture into several subapertures, the second step is to process the data in subapertures with an autofocus backprojection method, and the last step is to obtain the final CSAR image by merging the subimages obtained from the subaperture processing. The CSAR data processing results prove that the proposed strategy can remove the motion errors accurately and acquire well-focused CSAR images.

Circular synthetic aperture radar (CSAR) has a 360° observation capability on the central observation scenario. A typical way to process CSAR imaging is to cut data into small sub-apertures because most targets are only coherent at a very small observation angle. There are many sub-aperture imaging methods after development in recent years. The back-projection algorithm is widely used because it is simple and can be applied to an arbitrary trajectory. Because of the limitation of the Nyquist sampling frequency and influence of the antenna sidelobe, azimuth ambiguity is a phenomenon that may occur in the radar imaging process. The existing researches typically choose the back-projection (BP) imaging area according to the SAR platform flight path and the antenna beam width. The limitation of the CSAR imaging area and its azimuth ambiguity region are rarely analyzed theoretically. This paper focus on the sub-aperture imaging of CSAR, based on the BP algorithm, which derives the relationship of azimuth ambiguity with CSAR parameters such as the pause repeat frequency (PRF), slant range angle, velocity of radar platform, etc. This paper proposes an equation for the calculation of the azimuth ambiguity region and analyzes the limitations, which provides theoretical support for CSAR parameter design, imaging area selection, and azimuth ambiguity analysis.

Circular synthetic aperture radar (CSAR) is a high resolution 2D and 3D imaging mode, to obtain the demand of all observation information. Circular motion trajectory make motion compensation problem is very difficult. However, existing method, such as autofocus back projection (ABP) algorithm, cannot effectively solve the problem of motion compensation in CSAR. In this paper, an autofocus algorithm based on minimum entropy is used to solve this problem. It can accurately estimate phase errors in CSAR. The simulated CSAR data are used to validate performance of minimum entropy autofocus (MEA) algorithm.

A three dimensional (3D) imaging method which is a complex-valued generalized Radon transform (CGRT)-CLEAN algorithm for circular synthetic aperture radar (CSAR) is proposed in this chapter. Based on the analysis of CSAR echo model, the echo of a scatterer in the range-azimuth domain can be modeled as a single cycle sinusoid. Inspired by the generalized Radon transform, this chapter utilizes the CGRT to estimate for scatterers’ positions. Then, combining the CGRT with CLEAN technique, the parameters of a scatterer which include position information and reflection coefficient can be obtained. Thus, a 3D image of a target can also be reconstructed. The performances of the CGRT-CLEAN method have been verified by simulations, and the results confirm the effectiveness of the proposed algorithm for processing CSAR data.

An airborne circular synthetic aperture radar system captured data for a 5 km diameter area over 31 orbits. For this challenge problem, the phase history for 56 targets was extracted from the larger data set and placed on a DVD for public release. The targets include 33 civilian vehicles of which many are repeated models, facilitating training and classification experiments. The remaining targets include an open area and 22 reflectors for scattering and calibration research. The circular synthetic aperture radar provides 360 degrees of azimuth around each target. For increased elevation content, the collection contains two nine-orbit volumetric series, where the sensor reduces altitude between each orbit. Researchers are challenged to further the art of focusing, 3D imaging, and target discrimination for circular synthetic aperture radar.

Circular synthetic aperture radar (SAR) imaging on the geosynchronous orbit has many potential advantages, such as high-resolution three-dimensional (3D) imaging and continuous surveillance of broad area. The mission considered is an L-band geosynchronous circular SAR (GEOCSAR) with full aperture measurement. Since the integration time of GEOCSAR can be as long as 24 h, the orbit altitude is about 36 000 km and the coverage may reach 1/3 of the Earth's surface. The spatial and temporal variation of the ionosphere may impose significant effects on 3D imaging performance of GEOCSAR. The effects of ionospheric spatial variation including vertical and horizontal structure, the ionospheric turbulence and the ionospheric temporal variation are discussed. The analysis shows that the temporal variation of the ionospheric electron content during the synthetic aperture and the ionospheric turbulence may severely affect the GEOCSAR focusing performance on the XY plane. The vertical and horizontal structure of the ionosphere will cause image shift, and the dispersion effect is negligible.

3D scene reconstruction from single‐pass circular synthetic aperture radar (CSAR) data has been a research hot spot in various remote sensing applications. Among existing literature, radargrammetry techniques and model assistant methods are two dominant approaches. However, the performance of these methods is limited in practical applications: radargrammetry techniques obtain merely one height value along vertical; model assistant approaches only work when valid models are given. A single‐pass CSAR 3D scene point cloud reconstruction method is proposed. First, the connection between an object and its projections in multi‐aspect SAR images is established with no auxiliary model. On the basis of the connection, voxels are classified into inner voxels (voxels beneath the target profile) and outside voxels (voxels outside of the target profile). Discarded all the outside voxels, the remained inner voxels are combined to form the 3D point cloud of the target. It is similar to the sculpturing process from a raw material to a piece of craft. Finally, a 3D scene is retrieved through assembling all reconstructed targets into a unified coordinate system. The feasibility of the proposed method is validated by the Gotcha Volumetric SAR Data Set.

This paper deals with the issue of ground moving target imaging and motion parameter estimation with an airborne dual-channel circular stripmap synthetic aperture radar (CSSAR) system. Although several methods of ground moving target motion parameter estimation have been proposed for the conventional airborne linear stripmap SAR, they cannot be applied to airborne CSSAR because the range history of a ground moving target for airborne CSSAR is different than that for airborne linear stripmap SAR. In this paper, the moving target’s range history for airborne dual-channel CSSAR and the target signal model after the displaced phase center antenna processing are derived, and a new ground moving target imaging and motion parameter estimation algorithm is developed. In this algorithm, the estimation of baseband Doppler centroid and its compensation are first performed. Then focusing is implemented in the 2-D frequency domain via phase multiplication, and the target is focused in the SAR image without azimuth displacement due to the compensation of the Doppler shift caused by its motion. Finally, the target’s motion parameters are estimated with its Doppler parameters and its position in the SAR image. Numerical simulations are conducted to validate the derived range history and the performance of the proposed algorithm.

Circular synthetic aperture radar (CSAR) can obtain more complete scattering characteristics by observing the target with different azimuth angles. Therefore, extracting the complete structure of the target from CSAR images is of great significance for accurate interpretation. At present, the artificial target extraction based on CSAR images mostly uses anisotropic scattering features. For special targets such as buildings, as the walls and the ground form dihedral corner structures, there are also obvious strong scattering features such as double-scattering lines in SAR images. Therefore, combining the strong scattering features of buildings at specific aspects with anisotropic scattering characteristics at different aspects can obtain better extraction results, and how to extract these features accurately and efficiently is the key point. Based on this, this paper proposes a novel method for building contour extraction based on CSAR images. For strong scattering features, a fast fuzzy C-means (FCM) clustering algorithm was used to extract them. For anisotropic scattering features, aspect entropy was used to characterize the anisotropy degree, and K-means clustering was combined to extract. Finally, a more accurate result is obtained by merging the two feature extraction results. In order to verify the effectiveness and practicability of the proposed method, a lot of measured data acquired by the self-developed airborne L-band and Ku-band CSAR systems were processed. The experiments show that, compared with state-of-the-art algorithms, the proposed method can obtain more accurate results in less time.

Circular synthetic aperture radar (CSAR) enables 360-degree observation of the scene. Compared with coherent imaging, noncoherent imaging can suppress speckle and obtain a large number of texture features. However, due to the existence of a man-made anisotropic targets and the unique imaging geometry of CSAR, the different subaperture images are quite different, which makes the registration very difficult. Therefore, this manuscript proposed a factorized registration strategy. First, the full aperture is divided into multiple subapertures; then the adjacent subaperture images are registered and the noncoherent superimposition of the subaperture images yields the next stage image; finally, the previous step is performed iteratively until the final imaging result is obtained. Experimental results based on Ka-band CSAR data verify the effectiveness of the strategy.

Moving target brings out the different position shifts and defocusing across the image sequences acquired by circular synthetic aperture radar (CSAR) due to the Doppler shift and range smear effects. In this paper, a novel moving target detection approach for single-channel CSAR is proposed based on deep neural network (DNN). A dual-channel densely connected convolutional network (DenseNet) in consideration of complex-valued information is exploited for distinguishing the ground clutter and moving target. In terms of limited CSAR measure data set available for training the DNN network, simulated moving target samples are generated and fused into the measured ones under the various motion parameters. Finally, experiments have demonstrated that the proposed DenseNet for single-channel CSAR system processes an accepted detection performance and effectively overcomes the insufficiency of the limited dataset applications.

In circular synthetic aperture radar (CSAR), echo data simulation can provide ideal echo data for the processing of imaging and performance analysis. However, when the target scene is large, the amount of echo data is also large according to Nyquist sampling theorem. If the traditional serial computing way based on CPU is used, then the execution time is long. In this paper, we adopt graphic processing unit (GPU) to improve the computing speed. This GPU-accelerated way can be simply described as the process that CSAR echo data with carrier information is generated on GPU, and the subsequent removal of carrier is implemented on CPU. Simulation results show the GPU- accelerated way is faster than the CPU-based way when the target scene is large.

In this article, we propose a novel method of estimation of crack orientation on a metallic surface using linearly polarized circular synthetic aperture radar (SAR) imaging. We modeled a crack using a thin linear scatterer and considered the rotation of polarization basis vectors that were designed to match a predefined orientation vector corresponding to a temporary estimate of the orientation of the linear scatterer. The radar image intensity was expected to be a maximum when the specified orientation vector exactly matched the true scatterer orientation angle; therefore, to estimate the orientation of the scatterer, we aimed to obtain the maximum intensity of the image by varying the orientation vector. We validated the proposed scheme of estimation via a numerical electromagnetic simulation using the method of moments (MoM) and laboratory measurements carried out in an anechoic chamber. In this experiment, a metallic plate with slits was used as a simple surface crack model and the root mean square error and maximum error of the angular estimation were 1.9-degree and 5.1-degree, respectively.

This paper proposes a new ground moving target imaging algorithm for high-resolution airborne circular stripmap synthetic aperture radar (CSSAR)-ground moving target indication (GMTI) systems. In the proposed algorithm, the range cell migration correction is performed in the 2D frequency domain via a phase multiplication. The azimuth compression is performed in the range Doppler domain. A key step of the proposed algorithm is to utilize an iterative strategy to achieve an accurate correction of the range cell migration. This step makes the proposed algorithm work well for high-resolution CSSAR-GMTI systems. Numerical simulations are conducted to validate the proposed algorithm.